楼上的兄弟 什么时候能出来安装说明啊
小弟我已经等不急了哈
安装不难，只要有耐心，慢就一个字，不过装后，占用系统资源不是很厉害~~~
贴个跟主机连网的图看看:
希望大家将安装的详细步骤写下来和大家一起分享。谢谢！！
请教L:我也是安装成功了，，可就是无法从硬盘启动，， 郁闷的要死，
不知道家在那个session才是对的，还是要重新编辑一个脚本 ，才行，，，
节选自 帮助文件
6.1.1 Installation, step by step
This section describes how to install Solaris using the command-line version Simics.
Select the install script to use, depeding on Solaris version to install, either peanut-sol10-cd-install1.simics for Solaris 10, peanut-sol9-cd-install1.simics for Solaris 9, or peanut-sol8-cd-install1.simics for Solaris 8.
Set the path to the CD image in the simics script. The line
$cdrom_path = "sol-10-u2-ga-sparc-v1.iso"
should be changed to reflect the location and name of the CD image for stage one of the installlation. It can either be an ISO image file, or a CD-ROM device file (Linux and Solaris host only).
Start the first installation script, for example:
$ ./simics targets/sunfire/peanut-sol10-cd-install1.simics
and wait for it to complete. This may take several hours, depending on the performance of the host machine.
When the script stops, installation from the first CD is finished, and Solaris has tried to reboot the system. Since Simics does not support system reboot for this architecture, exit Simics at this point.
If the installation is performed from a real CD, it is now time to change disc in the drive. Also make sure that the path to the CD is correct in the second install script.
Now run the second script in the same way as the first, this script may also take a few hours to complete.
When the second script has stopped, run the third and last one. This script only takes a few minutes to finish.
When the third script has stopped the installation is ready. The newly created disk image has the following file name: peanut-sol<version>-install.disk. There are also a number of persistent state files.
To boot a machine with the newly installed Solaris OS, run the peanut-common.simics and make sure that the variable $os is set to "solaris10", "solaris9" or "solaris8" depending on the operating system version installed). Add a line like the following first in that simics script:
$os = "solaris10"
An optional last step is to compress the disk image with the craff utility to save some disk space.
simics中装好solaris后，能在这个solaris中安装oracle吗
好久没来这里了！没想到我的帖子也被加精了！呵呵呵！我当时也只是感兴趣的装了一下！其实并没有装成功！没想到大家对这款软件感兴趣！有机会我想再次尝试安装一下，如果真能安装的很圆满！我会把每一步都写得很详细贴上来！不过可能又要到今年十一了！毕竟那个时候才有空：）也希望安装成功的朋友能给些注意事项！如果它真能安装成功，我想我可能会放弃使用wmare了：）
Copyright 2001 Sun Microsystems, Inc. All rights reserved
Ethernet address 10:10:10:10:10:12, Host ID: 80804a6c.
ok boot cdrom -v
Boot device: /sbus@3,0/SUNW,fas@3,8800000/sd@6,0:f File and args: -v
Bad magic number in disk label
Can't open disk label package
Can't open boot device
ok
ok boot cdrom -v
Boot device: /sbus@3,0/SUNW,fas@3,8800000/sd@6,0:f File and args: -v
Bad magic number in disk label
Can't open disk label package
Can't open boot device
是怎么回事啊？跟iso有关吗？ 我用的是u5的最新Solaris10
simulation host
simulated machines 分别指的什么？
我装成功了，simics的solaris 10默认是u2的版本，我下了全套u2的cd iso。所有的iso文件都拷贝在$\workspace\target\sunfire,peanut-sol10-cd-install1.simics会引导安装u2 cd1，peanut-sol10-cd-install2.simics会安装u2 cd2-cd5，peanut-sol10-cd-install3.simics运行后基本不安装什么。最后需要修改的文件是peanut-common.simics ，文件最开头添加$os = "solaris10"(LZ的文档有误)。