solaris 10 NTFS 分区加载
Mount NTFS / Ext2 / Ext3 / FAT 16 / FAT 32 in SolarisI
often get queries about mounting NTFS / Ext2 / Ext3 /FAT 16 /FAT 32
partions in Solaris .Follow the below steps . Note that its only
read-only support for NTFS / Ext2 / Ext3 .
* Download packages
FSWpart
FSWfsmisc
Note these are packages for x86 Solaris .
* unzip the packages and install it
root~#gzcat FSWpart.tar.gz | tar xvf -
root~#gzcat FSWfsmisc.tar.gz | tar xvf -
root~#pkgadd -d . FSWpart
root~#pkgadd -d . FSWfsmisc
* Now run the prtpart tool
root~#/usr/sbin/prtpart
It would result in following output
root~#/usr/sbin/prtpart
Fdisk information for device /dev/rdsk/c1d0p0
Block Size : 512 bytes
Controller : ide
Disk : cmdk
Capacity : 74 GB
#start block# nblocks startCylSecHd endCylSecHd OSType
1: 0000000063 0006152832 0/ 1/ 1 7e/7f/fe Diagnostic
2: 0006152895 0025173855 7f/41/ 0 ff/ff/fe WIN95 FAT32(LBA)
3: 0031328640 0052432128 ff/ff/fe ff/ff/fe Solaris x86
4: 0083760830 0072535555 ff/ff/fe ff/ff/fe DOS Extended
#start block# nblocks startCylSecHd endCylSecHd OSType
5: 0000000001 0031407012 ff/ff/fe ff/ff/fe Linux native
0: 0031407013 0001994202 ff/ff/fe ff/ff/fe DOS Extended
#start block# nblocks startCylSecHd endCylSecHd OSType
6: 0000000063 0001994139 ff/ff/fe ff/ff/fe Linux swap
0: 0033401215 0039134340 ff/ff/fe ff/ff/fe DOS Extended
#start block# nblocks startCylSecHd endCylSecHd OSType
7: 0000000063 0039134277 ff/ff/fe ff/ff/fe WIN95 FAT32(Upto 2047GB)
Now note the disk id. In the above example its "/dev/rdsk/c1d0p0"
Now run
root~#/usr/sbin/prtpart /dev/rdsk/c1d0p0 -ldevs
Fdisk information for device /dev/rdsk/c1d0p0
** NOTE **
/dev/dsk/c1d0p0 - Physical device referring to entire physical disk
/dev/dsk/c1d0p1 - p4 - Physical devices referring to the 4 primary partitions
/dev/dsk/c1d0p5 ...- Virtual devices referring to logical partitions
Virtual device names can be used to access EXT2 and NTFS on logical partitions
/dev/dsk/c1d0p1 Diagnostic
/dev/dsk/c1d0p2 WIN95 FAT32(LBA)
/dev/dsk/c1d0p3 Solaris x86
/dev/dsk/c1d0p4 DOS Extended
/dev/dsk/c1d0p5 Linux native
/dev/dsk/c1d0p6 Linux swap
/dev/dsk/c1d0p7 WIN95 FAT32(Upto 2047GB)
The above command scan you hard-disk and displays all available filesystems. Note the required filesystems to be mounted.
To mount NTFS partition use
root~#mount -F ntfs/dev/dsk/c1d0p /mnt/windows
To mount FAT 16 /FAT 32 partition use
root~#mount -F pcfs/dev/dsk/c1d0p /mnt/windows
if the above command fails you can try the below option
root~#prtpart /dev/dsk/c1d0p0 -fat
the above command should list the available PCFS / FAT partitions in colon notation, then use the same for mounting (eg)
root~#mount -F pcfs/dev/dsk/c1d0p0:d /mnt/windows
To mount Ext2 / Ext3 partitions use
root~#mount -F ext2fs /dev/dsk/c1d0p /mnt/linux
To unmount a partition use "umount "
root~#umount /mnt/linux
本文来自ChinaUnix博客，如果查看原文请点：http://blog.chinaunix.net/u/2056/showart_499221.html
页:
[1]