【E3500】找不到本地硬盘

westlife521 发表于 2009-04-13 23:14

7,0> Ecache Quick Verify
7,0> Ecache Init
7,0> Ecache RAM
7,0> Ecache Address Line
7,0> Configure Ecache Limit
7,0>Ecache Size = 00400000,Limited to 00400000
7,0>Board 7 FPU Functional Test
7,0> FPU Enable
7,0>Board 7 Board Master Select Test
7,0> Selecting a Board Master
7,0>Board 7 FireHose Devices Test
7,0>Board 7 Address Controller Test
7,0> AC Initialization
7,0> AC DTAG Init
7,0>Board 7 Dual Tags Test
7,0> AC DTAG Init
7,0>Board 7 FireHose Controller Test
7,0> FHC Initialization
7,0>WARNING FanFail State Machine Status at 000001ff.f0804010 is 00000001
7,0>Board 7 JTAG Test
7,0> Verify System Board Scan Ring
7,0>Board 7 Centerplane Test
7,0> Centerplane Join
7,0>Setting JTAG Master
7,0>Clear JTAG Master
7,0>Board 7 Setup Cache Size Test
7,0> Setting Up Cache Size
7,0>Board 7 System Master Select Test
7,0> Setting System Master
7,0>POST Master Selected (JTAG,CENTRAL)
7,0>Board 16 Clock Board Test
7,0> Clock Board Initialization
7,0> Clock Board Temperature Check
7,0>Board 16 Clock Board Serial Ports Test
7,0>Board 16 NVRAM Devices Test
7,0> M48T59 (TOD) Init
7,0>Board 7 System Board ProbeTest
7,0> Probing all CPU/Memory BDA
7,0> Probing System Boards
7,0> Probing CPU Module JTAG Rings
7,0>Setting System Clock Frequency
7,0> CPU Module mid 14 Checked in OK (speed code = 2)
7,0> CPU mid 18 Version=00170011.90000507
7,0> CPU Module mid 18 Checked in OK (speed code = 2)
7,0> CPU mid 19 Version=00170011.a0000507
7,0> CPU Module mid 19 Checked in OK (speed code = 2)
7,0> ******** Clock Reset - retesting
7,0>System Frequency (MHz),fcpu=400, fmod=200, fsys=100, fgen=400
7,0>
7,0>@(#) POST 3.9.10 1999/02/19 14:23
7,0>
SelfTest Initializing (Diag Level 40, ENV 0000ff80) IMPL 0011 MASK 90
7,0>Board 7 CPU FPROM Test
7,0> CPU/Memory Board FPROM Checksum Test
7,0>Board 7 Basic CPU Test
7,0> FPU Registers and Data Path Test
7,0> Instruction Cache Tag RAM Test
7,0> Instruction Cache Instruction RAM Test
7,0> Instruction Cache Next Field RAM Test
7,0> Instruction Cache Pre-decode RAM Test
7,0> Data Cache RAM Test
7,0> Data Cache Tags Test
7,0> DMMU Registers Access Test
7,0> DMMU TLB DATA RAM Access Test
7,0> DMMU TLB TAGS Access Test
7,0> IMMU Registers Access Test
7,0> IMMU TLB DATA RAM Access Test
7,0> IMMU TLB TAGS Access Test
7,0> Set CPU UPA Config and Init SDB Data
7,0> SRAM Mode = 22, Clock Mode = 4:1, PCON = 6fa, MCAP = 0
7,0>Board 7 MMU Enable Test
7,0> DMMU Init
7,0> IMMU Init
7,0> Mapping Selftest Enabling MMUs
7,0>Board 7 Ecache Test
7,0> Ecache Probe
7,0> Ecache Tags
7,0> Ecache Quick Verify
7,0> Ecache Init
7,0> Ecache RAM
7,0> Ecache 6N RAM Pattern Test
7,0> Ecache Address Line
7,0> Configure Ecache Limit
7,0>Ecache Size = 00400000,Limited to 00400000
7,0>Board 7 FPU Functional Test
7,0> FPU Enable
7,0>Board 7 Board Master Select Test
7,0> Selecting a Board Master
7,0>Board 7 FireHose Devices Test
7,0> PROM Datapath Test
7,0> FHC CPU SRAM Test
7,0>Board 7 Address Controller Test
7,0> AC Registers Test
7,0> AC Initialization
7,0> Memory RegistersTest
7,0> Memory Registers Initialization Test
7,0> AC DTAG Init
7,0>Board 7 Dual Tags Test
7,0> AC DTAG Test
7,0> AC DTAG Init
7,0>Board 7 FireHose Controller Test
7,0> FHC Initialization
7,0>WARNING FanFail State Machine Status at 000001ff.f0804010 is 00000001
7,0>Board 7 JTAG Test
7,0> Verify System Board Scan Ring
7,0>Board 7 Centerplane Test
7,0> Centerplane and Arbiter Check Test
7,0>Setting JTAG Master
7,0>Clear JTAG Master
7,0> Centerplane Join
7,0>Setting JTAG Master
7,0>Clear JTAG Master
7,0>Board 7 Setup Cache Size Test
7,0> Setting Up Cache Size
7,0>Board 7 System Master Select Test
7,0> Setting System Master
7,0>POST Master Selected (JTAG,CENTRAL)
7,0>Board 16 Clock Board Test
7,0> Clock Board Registers Test
7,0> Clock Board Initialization
7,0> Clock Board Temperature Check
7,0>Board 16 Clock Board Serial Ports Test
7,0> 85C30 Register Test
7,0> 85C30 Serial Ports Test
7,0> Keyboard Loopback
7,0> Mouse Loopback
7,0> Serial Port B Loopback
7,0> Remote Serial Port A Loopback
7,0> Remote Serial Port B Loopback
7,0>Board 16 NVRAM Devices Test
7,0> M48T59 (TOD) Init
7,0> M48T59 (TOD) Functional Part 1 Test
7,0> NVRAM(Non-Destructive) Test
7,0>Board 7 System Board ProbeTest
7,0> Probing all CPU/Memory BDA
7,0> Probing System Boards
7,0> Probing CPU Module JTAG Rings
7,0>Setting System Clock Frequency
7,0> CPU Module mid 14 Checked in OK (speed code = 2)
7,0> CPU mid 18 Version=00170011.90000507
7,0> CPU Module mid 18 Checked in OK (speed code = 2)
7,0> CPU mid 19 Version=00170011.a0000507
7,0> CPU Module mid 19 Checked in OK (speed code = 2)
7,0>System Frequency (MHz),fcpu=400, fmod=200, fsys=100, fgen=400
7,0>TESTING BOARD 1
7,0>Board 1 JTAG Test
7,0> Verify System Board Scan Ring
7,0>Board 1 Centerplane Test
7,0> Centerplane Check
7,0>Board 1 Address Controller Test
7,0> AC Registers Test
7,0> AC Initialization
7,0>Setting Freq to 25MHZ
7,0> Memory RegistersTest
7,0> Memory Registers Initialization Test
7,0> AC DTAG Init
7,0>Board 1 FireHose Controller Test
7,0> FHC Initialization
7,0>Board 1 NVRAM Devices Test
7,0> M48T59 (TOD) Init
7,0> M48T59 (TOD) Functional Part 1 Test
7,0> NVRAM(Non-Destructive) Test
7,0>TESTING BOARD 5
7,0>Board 5 JTAG Test
7,0> Verify System Board Scan Ring
7,0>Board 5 Centerplane Test
7,0> Centerplane Check
7,0>Board 5 Address Controller Test
7,0> AC Registers Test
7,0> AC Initialization
7,0>Setting Freq to 25MHZ
7,0> Memory RegistersTest
7,0> Memory Registers Initialization Test
7,0> AC DTAG Init
7,0>Board 5 FireHose Controller Test
7,0> FHC Initialization
7,0>WARNING FanFail State Machine Status at 000001d4.f8804010 is 00000001
7,0>Board 5 NVRAM Devices Test
7,0> M48T59 (TOD) Init
7,0> M48T59 (TOD) Functional Part 1 Test
7,0> NVRAM(Non-Destructive) Test
7,0>Re-mapping to Local Device Space
7,0>Begin Central Space Serial Port access
7,0>Enable AC Control Parity
7,0>Hotplug Trigger Test
7,0>Init Counters for Hotplug
7,0>Board 7 Cross Calls Test
7,0> Cross Calls Test
7,0>Displaying PROM Versions
7,0>Slot 1 IO Type 4 FCODE 1.8.24 1999/12/23 17:30iPOST 3.4.24 1999/12/23 17:34
7,0>Slot 5 IO Type 4 FCODE 1.8.24 1999/12/23 17:30iPOST 3.4.24 1999/12/23 17:34
7,0>Slot 7 CPU/Memory OBP 3.2.21 1999/2/19 14:33POST3.9.10 1999/2/19 14:23
7,0>Slot 9 CPU/Memory OBP 3.2.21 1999/2/19 14:33POST3.9.10 1999/2/19 14:23
7,0>Board 7 Environmental Probe Test
7,0> Environmental Probe
7,0>ERROR: TEST=Environmental Probe,SUBTEST=Environmental Probe ID=1f.1
7,0>Component under test: Board 7 System Interrupt
7,0>Peripherial Power Supply PPSS_0 Failed
7,0>ERROR: TEST=Environmental Probe,SUBTEST=Environmental Probe ID=1f.1
7,0>Component under test: Board 7 System Interrupt
7,0>Peripherial Power Supply PPSS_0 Failed
7,0>Checking Power Supply Configuration
7,0>Power is adequate, load 4 ps 2
7,0>
7,0> System Environmental Status
7,0>-----------------------------------------------------------------
7,0> SlotBoard Type Temp PS Stat    Perph PS
7,0>-----------------------------------------------------------------
7,0>0| Empty    |    |          | PP0 FAIL |
7,0>1|+IO Type 4 | <42| PS1 OK | PP1 N_PRES |
7,0>2| Empty    |    |          |          |
7,0>3| Empty    |    | PS3 FANFAIL|          |
7,0>4| Empty    |    |          |          |
7,0>5|+IO Type 4 | <42| PS5 OK |          |
7,0>6| Empty    |    |          |          |
7,0>7|+CPU/Memory| <37|          |          |
7,0>8| Empty    |    |          |          |
7,0>9|+CPU/Memory| <44|          |          |
7,0> 16| Clock Board | <42|          |          |
7,0>-----------------------------------------------------------------
7,0>
7,0> Precharge and Peripheral Power Supply Status
7,0>-----------------------------------------------------------------
7,0> V5_PCH V3_PCH V12_PCHV5_PPCHV5_AUX V12_P V5_P
7,0>-----------------------------------------------------------------
7,0> FAIL | FAIL | FAIL | FAIL | OK | FAIL | OK |
7,0>-----------------------------------------------------------------
7,0>
7,0> Miscellaneous Sensor Status
7,0>-----------------------------------------------------------------
7,0> RK_FAN AC_FAN KEY_FANCLK_33 CLK_50 NOT_BD_PRES
7,0>-----------------------------------------------------------------
7,0> FAIL | OK | OK | OK | OK | ONE |
7,0>-----------------------------------------------------------------
7,0>Reconfig memory due to POR or CLOCK RESET
7,0>Reconfig memory due to DIAG_LEVEL
7,0>Board 7 Probing Memory SIMMS Test
7,0> Probe SIMMID
7,0> Populated Memory Bank Status
7,0>          bd # Size Address Way Status
7,0>          7    256                   Normal
7,0>          7    256                   Normal
7,0>          9    256                   Normal
7,0>          9    256                   Normal
7,0>Board 7 Memory Configuration Test
7,0> Memory Interleaving
7,0> Total banks with 8MB SIMMs = 0
7,0> Total banks with 32MB SIMMs = 4
7,0> Total banks with 128MB SIMMs = 0
7,0> Total banks with 256MB SIMMs = 0
7,0> Overall memory default speed = 60ns
7,0>Do OPTIMAL INTLV
7,0> Board 7 AC rev 5 RCTIME = 1 (Tras 71)
7,0> Board 9 AC rev 5 RCTIME = 1 (Tras 71)
7,0> Board 7 AC rev 5 RCTIME = 1 (Tras 71)
7,0> Board 9 AC rev 5 RCTIME = 1 (Tras 71)
7,0> Memory Refresh Enable
7,0>Board 7 SIMMs Test
7,0> MP Memory SIMM Clear Test
7,0> Memory Size is 1024Mbytes
7,0>    CPU MID 18 clearing 00000000.00004000 to 00000000.15500000
7,0>    CPU MID 19 clearing 00000000.15500000 to 00000000.2aa00000
7,0>    CPU MID 14 clearing 00000000.2aa00000 to 00000000.40000000
7,0>    CPU MID 14 clearing 00000000.00000000 to 00000000.00004000
7,0> Memory Walking Rows and Columns Test
7,0> MP Memory SIMM (6N RAM Patterns) Test
7,0> Memory Size is 1024Mbytes
7,0>    CPU MID 18 testing 00000000.00000000 to 00000000.15500000
7,0>    CPU MID 19 testing 00000000.15500000 to 00000000.2aa00000
7,0>    CPU MID 14 testing 00000000.2aa00000 to 00000000.40000000
7,0> MP Memory SIMM (moving inverse) Test
7,0> Memory Size is 1024Mbytes
7,0>    CPU MID 18 testing 00000000.00000000 to 00000000.15500000
7,0>    CPU MID 19 testing 00000000.15500000 to 00000000.2aa00000
7,0>    CPU MID 14 testing 00000000.2aa00000 to 00000000.40000000
7,0>Slave CPU Functional Tests
7,0> Slave CPU MID 18 started
9,0>Board 9 Functional CPU 0 Test
9,0> Dcache Init
9,0> Dcache Enable Test
9,0> Dcache Functionality Test
9,0> Ecache Stress Test
9,0> Ecache Functional Test
9,0> CPU Dispatch (Multi-Scalar) Test
9,0> SPARC Atomic Instructions Test
9,0> SPARC Prefetch Instructions Test
9,0> CPU Softint Registers and Interrupts Test
9,0> Uni-Processor Cache Coherence Test
9,0> Branch Memory Test
9,0> SDB ECC CE Test
9,0> SDB ECC Uncorrectable Test
9,0> FPU Instruction Test
7,0> Slave CPU MID 19 started
9,1>Board 9 Functional CPU 1 Test
9,1> Dcache Init
9,1> Dcache Enable Test
9,1> Dcache Functionality Test
9,1> Ecache Stress Test
9,1> Ecache Functional Test
9,1> CPU Dispatch (Multi-Scalar) Test
9,1> SPARC Atomic Instructions Test
9,1> SPARC Prefetch Instructions Test
9,1> CPU Softint Registers and Interrupts Test
9,1> Uni-Processor Cache Coherence Test
9,1> Branch Memory Test
9,1> SDB ECC CE Test
9,1> SDB ECC Uncorrectable Test
9,1> FPU Instruction Test
7,0>Board 7 Functional CPU 0 Test
7,0> Dcache Init
7,0> Dcache Enable Test
7,0> Dcache Functionality Test
7,0> Ecache Stress Test
7,0> Ecache Functional Test
7,0> CPU Dispatch (Multi-Scalar) Test
7,0> SPARC Atomic Instructions Test
7,0> SPARC Prefetch Instructions Test
7,0> CPU Softint Registers and Interrupts Test
7,0> Uni-Processor Cache Coherence Test
7,0> Branch Memory Test
7,0> SDB ECC CE Test
7,0> SDB ECC Uncorrectable Test
7,0> FPU Instruction Test
7,0>TESTING IO BOARD 1
7,0>Board 1 I/O FPROM Test
7,0> I/O Board EPROM checksum Test
7,0>@(#) iPOST 3.4.24 1999/12/23 17:34
7,0> TESTING IO BOARD 1 ASICs
7,0> TESTING SysIO Port 0
7,0>Board 1 SysIO Registers Test
7,0> SysIO Register Initialization
7,0> IOMMU Registers and RAM Test
7,0> Streaming Buffer Registers and RAM Test
7,0> SBus Control and Config Registers Test
7,0> SysIO RAM Initialization
7,0>Board 1 SysIO Functional Test
7,0> Clear Interrupt Map and State Registers
7,0> SysIO InterruptsTest
7,0> SysIO Timers/Counters Test
7,0> IOMMU Virtual Address TLB Tag Compare Test
7,0> Streaming Buffer Flush Test
7,0> DMA Merge Buffer Test
7,0> SYSIO ECC Correctable Test
7,0> SYSIO ECC UnCorrectable Test
7,0> SysIO Sbus Probe Test
7,0> SysIO Register Initialization Test
7,0> SysIO RAM Initialization Test
7,0> Clear Interrupt Map and State Registers Test
7,0>Board 1 OnBoard IO Chipset (SOC) Test
7,0> SOC SRAM Test
7,0> SOC Registers Test
7,0> SOC Interrupt Test
7,0> Clear Interrupt Map and State Registers Test
7,0> TESTING SysIO Port 1
7,0>Board 1 SysIO Registers Test
7,0> SysIO Register Initialization
7,0> IOMMU Registers and RAM Test
7,0> Streaming Buffer Registers and RAM Test
7,0> SBus Control and Config Registers Test
7,0> SysIO RAM Initialization
7,0>Board 1 SysIO Functional Test
7,0> Clear Interrupt Map and State Registers
7,0> SysIO InterruptsTest
7,0> SysIO Timers/Counters Test
7,0> IOMMU Virtual Address TLB Tag Compare Test
7,0> Streaming Buffer Flush Test
7,0> DMA Merge Buffer Test
7,0> SYSIO ECC Correctable Test
7,0> SYSIO ECC UnCorrectable Test
7,0> SysIO Sbus Probe Test
7,0> SysIO Register Initialization Test
7,0> SysIO RAM Initialization Test
7,0> Clear Interrupt Map and State Registers Test
7,0>Board 1 OnBoard IO Chipset (FEPS) Test
7,0> FAS366 Registers Test
7,0> ESP FAS366 DVMA burst mode read/write Test
7,0> FAS366 FIFO TO DMA Test
7,0> DMA TO FAS366 FIFO Test
7,0> FEPS (Ethernet) Registers Test
7,0> FEPS Ethernet(BM, DP83840, Twister) Internal Loopbacks Test
7,0> SysIO Register Initialization Test
7,0> SysIO RAM Initialization Test
7,0> Clear Interrupt Map and State Registers Test
7,0>IO BOARD 1 TESTED
7,0>TESTING IO BOARD 5
7,0>Board 5 I/O FPROM Test
7,0> I/O Board EPROM checksum Test
7,0>@(#) iPOST 3.4.24 1999/12/23 17:34
7,0> TESTING IO BOARD 5 ASICs
7,0> TESTING SysIO Port 0
7,0>Board 5 SysIO Registers Test
7,0> SysIO Register Initialization
7,0> IOMMU Registers and RAM Test
7,0> Streaming Buffer Registers and RAM Test
7,0> SBus Control and Config Registers Test
7,0> SysIO RAM Initialization
7,0>Board 5 SysIO Functional Test
7,0> Clear Interrupt Map and State Registers
7,0> SysIO InterruptsTest
7,0> SysIO Timers/Counters Test
7,0> IOMMU Virtual Address TLB Tag Compare Test
7,0> Streaming Buffer Flush Test
7,0> DMA Merge Buffer Test
7,0> SYSIO ECC Correctable Test
7,0> SYSIO ECC UnCorrectable Test
7,0> SysIO Sbus Probe Test
7,0> SysIO Register Initialization Test
7,0> SysIO RAM Initialization Test
7,0> Clear Interrupt Map and State Registers Test
7,0>Board 5 OnBoard IO Chipset (SOC) Test
7,0> SOC SRAM Test
7,0> SOC Registers Test
7,0> SOC Interrupt Test
7,0> Clear Interrupt Map and State Registers Test
7,0> TESTING SysIO Port 1
7,0>Board 5 SysIO Registers Test
7,0> SysIO Register Initialization
7,0> IOMMU Registers and RAM Test
7,0> Streaming Buffer Registers and RAM Test
7,0> SBus Control and Config Registers Test
7,0> SysIO RAM Initialization
7,0>Board 5 SysIO Functional Test
7,0> Clear Interrupt Map and State Registers
7,0> SysIO InterruptsTest
7,0> SysIO Timers/Counters Test
7,0> IOMMU Virtual Address TLB Tag Compare Test
7,0> Streaming Buffer Flush Test
7,0> DMA Merge Buffer Test
7,0> SYSIO ECC Correctable Test
7,0> SYSIO ECC UnCorrectable Test
7,0> SysIO Sbus Probe Test
7,0> SysIO Register Initialization Test
7,0> SysIO RAM Initialization Test
7,0> Clear Interrupt Map and State Registers Test

westlife521 发表于 2009-04-13 23:16

7,0>Board 5 OnBoard IO Chipset (FEPS) Test
7,0> FAS366 Registers Test
7,0> ESP FAS366 DVMA burst mode read/write Test
7,0> FAS366 FIFO TO DMA Test
7,0> DMA TO FAS366 FIFO Test
7,0> FEPS (Ethernet) Registers Test
7,0> FEPS Ethernet(BM, DP83840, Twister) Internal Loopbacks Test
7,0> SysIO Register Initialization Test
7,0> SysIO RAM Initialization Test
7,0> Clear Interrupt Map and State Registers Test
7,0>IO BOARD 5 TESTED
7,0>SYSTEM LEVEL TESTING
7,0>Board 7 Cache Coherency Test
7,0> Multi-Processor Cache Coherence Test
7,0> Testing CPU MID 18
7,0> Testing CPU MID 19
7,0>Probing for Disk System boards
7,0>Board 7 System Interrupts Test
7,0> System Interrupts Test
7,0>ERROR: TEST=System Interrupts,SUBTEST=System Interrupts ID=1f.1
7,0>Component under test: Board 7 System Interrupt
7,0>Peripherial Power Supply PPSS_0 Failed
7,0>ERROR: TEST=System Interrupts,SUBTEST=System Interrupts ID=1f.1
7,0>Component under test: Board 7 System Interrupt
7,0>Peripherial Power Supply PPSS_0 Failed
7,0>Checking Power Supply Configuration
7,0>Power is adequate, load 4 ps 2
7,0>
7,0> System Environmental Status
7,0>-----------------------------------------------------------------
7,0> SlotBoard Type Temp PS Stat    Perph PS
7,0>-----------------------------------------------------------------
7,0>0| Empty    |    |          | PP0 FAIL |
7,0>1|+IO Type 4 | <42| PS1 OK | PP1 N_PRES |
7,0>2| Empty    |    |          |          |
7,0>3| Empty    |    | PS3 FANFAIL|          |
7,0>4| Empty    |    |          |          |
7,0>5|+IO Type 4 | <42| PS5 OK |          |
7,0>6| Empty    |    |          |          |
7,0>7|+CPU/Memory| <37|          |          |
7,0>8| Empty    |    |          |          |
7,0>9|+CPU/Memory| <44|          |          |
7,0> 16| Clock Board | <42|          |          |
7,0>-----------------------------------------------------------------
7,0>
7,0> Precharge and Peripheral Power Supply Status
7,0>-----------------------------------------------------------------
7,0> V5_PCH V3_PCH V12_PCHV5_PPCHV5_AUX V12_P V5_P
7,0>-----------------------------------------------------------------
7,0> FAIL | FAIL | FAIL | FAIL | OK | FAIL | OK |
7,0>-----------------------------------------------------------------
7,0>
7,0> Miscellaneous Sensor Status
7,0>-----------------------------------------------------------------
7,0> RK_FAN AC_FAN KEY_FANCLK_33 CLK_50 NOT_BD_PRES
7,0>-----------------------------------------------------------------
7,0> FAIL | OK | OK | OK | OK | ONE |
7,0>-----------------------------------------------------------------
7,0>WARNING Test skipped, Interrupts Pending
7,0> Check Board Present Test
7,0> Board Present Interrupt Test
7,0>POST Failed
7,0>
7,0> System Board Status
7,0>-----------------------------------------------------------------
7,0> Slot Board Status Board Type    Failures
7,0>-----------------------------------------------------------------
7,0>0| Not installed|          |
7,0>1| Normal       |+IO Type 4 |
7,0>2| Not installed|          |
7,0>3| Not installed|          |
7,0>4| Not installed|          |
7,0>5| Normal       |+IO Type 4 |
7,0>6| Not installed|          |
7,0>7| Normal       |+CPU/Memory|
7,0>8| Not installed|          |
7,0>9| Normal       |+CPU/Memory|
7,0> 16| Online/failure | Clock Board | PPS_DC_FAIL AC_FAIL DISK_FAN_FAIL
7,0>-----------------------------------------------------------------
7,0>
7,0> CPU Module Status
7,0>-----------------------------------------------------------------
7,0> MIDOKCacheSpeed Version
7,0>-----------------------------------------------------------------
7,0> 14 | y | 4096|400| 00170011.90000507
7,0> 18 | y | 4096|400| 00170011.90000507
7,0> 19 | y | 4096|400| 00170011.a0000507
7,0>-----------------------------------------------------------------
7,0>System Frequency (MHz),fcpu=400, fmod=200, fsys=100, fgen=400
7,0> Populated Memory Bank Status
7,0>          bd # Size Address Way Status
7,0>          7    256 0    4    Normal
7,0>          7    256 2    4    Normal
7,0>          9    256 1    4    Normal
7,0>          9    256 3    4    Normal
7,0>
7,0>
   POST COMPLETE
7,0>Entering OBP

ttya initialized
Using POST's System Configuration
Setting up memory
Starting CPU ID 18
Starting CPU ID 19
Clock board TOD does not match TOD on any IO board.
fhc ac simm-status environment sram flashprom SUNW,UltraSPARC-II
fhc ac simm-status environment sram flashprom SUNW,UltraSPARC-II SUNW,UltraSPARC-II
Probing UPA Slot at 2,0 sbus fhc ac environment flashprom eeprom sbus-speed counter-timer
Probing UPA Slot at 3,0 sbus counter-timer
Probing UPA Slot at a,0 sbus fhc ac environment flashprom eeprom sbus-speed counter-timer
Probing UPA Slot at b,0 sbus counter-timer
Probing /sbus@2,0 at d,0SUNW,socal sf ssd sf ssd
Probing /sbus@2,0 at 1,0QLGC,isp sd st
Probing /sbus@2,0 at 2,0SUNW,qfe SUNW,qfe SUNW,qfe SUNW,qfe
Probing /sbus@3,0 at 3,0SUNW,hme SUNW,fas sd st
Probing /sbus@3,0 at 0,0QLGC,isp sd st
Probing /sbus@a,0 at d,0SUNW,socal sf ssd sf ssd
Probing /sbus@a,0 at 1,0QLGC,isp invalid command
sd st
Probing /sbus@a,0 at 2,0Nothing there
Probing /sbus@b,0 at 3,0SUNW,hme SUNW,fas sd st
Probing /sbus@b,0 at 0,0Nothing there
screen not found.
Can't open input device.
Keyboard not present.Using ttya for input and output.
Using POST's System Configuration
Setting up memory
Starting CPU ID 18
Starting CPU ID 19
Clock board TOD does not match TOD on any IO board.
fhc ac simm-status environment sram flashprom SUNW,UltraSPARC-II
fhc ac simm-status environment sram flashprom SUNW,UltraSPARC-II SUNW,UltraSPARC-II
Probing UPA Slot at 2,0 sbus fhc ac environment flashprom eeprom sbus-speed counter-timer
Probing UPA Slot at 3,0 sbus counter-timer
Probing UPA Slot at a,0 sbus fhc ac environment flashprom eeprom sbus-speed counter-timer
Probing UPA Slot at b,0 sbus counter-timer
Probing /sbus@2,0 at d,0SUNW,socal sf ssd sf ssd
Probing /sbus@2,0 at 1,0QLGC,isp sd st
Probing /sbus@2,0 at 2,0SUNW,qfe SUNW,qfe SUNW,qfe SUNW,qfe
Probing /sbus@3,0 at 3,0SUNW,hme SUNW,fas sd st
Probing /sbus@3,0 at 0,0QLGC,isp sd st
Probing /sbus@a,0 at d,0SUNW,socal sf ssd sf ssd
Probing /sbus@a,0 at 1,0QLGC,isp invalid command
sd st
Probing /sbus@a,0 at 2,0Nothing there
Probing /sbus@b,0 at 3,0SUNW,hme SUNW,fas sd st
Probing /sbus@b,0 at 0,0Nothing there

5-slot Sun Enterprise E3500, No Keyboard
OpenBoot 3.2.21, 1024 MB memory installed, Serial #11149122.
Ethernet address 8:0:20:aa:1f:42, Host ID: 80aa1f42.

Port#0 received soc-status=14 loop 0 is ONLINE
login-all? failed

No ONLINE status! Please check H/W or cable.
Port#0 received soc-status=14 loop 0 is ONLINE
login-all? failed

No ONLINE status! Please check H/W or cable.
Port#0 received soc-status=14 loop 0 is ONLINE
login-all? failed

No ONLINE status! Please check H/W or cable.
Port#0 received soc-status=14 loop 0 is ONLINE
login-all? failed

No ONLINE status! Please check H/W or cable.
Port#0 received soc-status=14 loop 0 is ONLINE
login-all? failed

No ONLINE status! Please check H/W or cable.
Port#0 received soc-status=14 loop 0 is ONLINE
login-all? failed
Boot device: netFile and args:
Using Onboard Transceiver - Link Up.
Timeout waiting for ARP/RARP packet
Timeout waiting for ARP/RARP packet
Timeout waiting for ARP/RARP packet
Timeout waiting for ARP/RARP packet
Timeout waiting for ARP/RARP packet

{e} ok
{e} ok probe-scsi-all
/sbus@b,0/SUNW,fas@3,8800000

/sbus@a,0/QLGC,isp@1,10000
invalid command
Target 5
Unit 0 Disk Symbios StorEDGE A10000301
                                             ?G乕
Unit 1 Disk Symbios StorEDGE A10000301
                                             ?G乕
Unit 2 Disk Symbios StorEDGE A10000301
                                             ?G乗
Unit 3 Disk Symbios StorEDGE A10000301
                                             ?G乗
Unit 4 Disk Symbios StorEDGE A10000301
                                             ?G乗;
Unit 5 Disk Symbios StorEDGE A10000301
                                             ?G乗Z
Unit 6 Device type 20 Symbios StorEDGE A10000301          tSnl焛
Unit 7 Device type 20 Symbios StorEDGE A10000301          tSnDti

/sbus@3,0/QLGC,isp@0,10000
Target 5
Unit 0 Disk Symbios StorEDGE A10000205矴G乕
Unit 1 Disk Symbios StorEDGE A10000205矴G亶
Unit 2 Device type 20 Symbios StorEDGE A10000205          苞?3\?
Unit 3 Device type 20 Symbios StorEDGE A10000205          埾?3\?
Unit 4 Device type 20 Symbios StorEDGE A10000205          Q?3\?
Unit 5 Device type 20 Symbios StorEDGE A10000205          ??3\?
Unit 6 Device type 20 Symbios StorEDGE A10000205          苞?3\?
Unit 7 Device type 20 Symbios StorEDGE A10000205          埾?3\?

/sbus@3,0/SUNW,fas@3,8800000

/sbus@2,0/QLGC,isp@1,10000
Target 0
Unit 0 Removable Device type 8 EXABYTE EXB-220       4.114.11.008

Target 1
Unit 0 Removable Tape EXABYTE EXB-89008E030203V39e

                                 0060128735

{e} ok
{e} ok

找不到本地硬盘...............

solaris_unix 发表于 2009-04-14 09:22

看看是不是硬盘有问题了，或者是光纤环路有问题了！

bencyber 发表于 2009-04-14 10:00

电源有问题，
7,0>-----------------------------------------------------------------
7,0> V5_PCH V3_PCH V12_PCHV5_PPCHV5_AUX V12_P V5_P
7,0>-----------------------------------------------------------------
7,0> FAIL | FAIL | FAIL | FAIL | OK | FAIL | OK |
7,0>-----------------------------------------------------------------

7,0>Board 7 System Interrupts Test
7,0> System Interrupts Test
7,0>ERROR: TEST=System Interrupts,SUBTEST=System Interrupts ID=1f.1
7,0>Component under test: Board 7 System Interrupt
7,0>Peripherial Power Supply PPSS_0 Failed
7,0>ERROR: TEST=System Interrupts,SUBTEST=System Interrupts ID=1f.1
7,0>Component under test: Board 7 System Interrupt
7,0>Peripherial Power Supply PPSS_0 Failed
7,0>Checking Power Supply Configuration

easybegin 发表于 2009-04-14 10:08

主电源坏了，当然找不到硬盘了

westlife521 发表于 2009-04-14 10:55

回复 #5 easybegin 的帖子

有点不明白

为什么PPS0 故障的话，机器还能点亮，还能跑post啊，pps0不是主供电电源吗？

孔方兄 发表于 2009-04-14 10:57

E3500除了后面的电源模块外，还有前端的供电模块的；估计是这个问题；两个PS的订货编号是不一样的；

westlife521 发表于 2009-04-14 11:08

回复 #7 孔方兄的帖子

前面那个我看是空的.........

货号的话应该是这个吧

X9689A 300-1358 FDK PEX750-30 195 Watt Peripheral Power Supply (Type A129) Front Unit

Aaron.Lau 发表于 2011-04-28 15:32

我也碰到相同问题，这么解决的：

E3500的内置硬盘是fcal的，也需要至少接一条光纤线从IO板的GBIC到左边的FCAL-IB板下面的GBIC光纤口

找一条光纤线接上，如果已经接了光纤线，重新插拔一下。
确认ok probe-fcal-all能看到硬盘 ...

东方蜘蛛 发表于 2011-04-29 13:49

:luya:还有人用这古董呢，赶紧让退休了吧。。。。。顺便学习下:em15:

页: [1] 2

Chinaunix's Archiver