jl8323 发表于 2009-10-28 10:49

ids11.5 for solaris install

大家有谁装过ids11.5 for solaris?
主要是kernel调整这块。或者,....../release/en_us/0333/ids_machine_notes_11.50.txt发给我也行。
多谢!

liaosnet 发表于 2009-10-28 10:59

没这个版本~~如果你要安装,你把那个包解开就能看到这个文件....

jl8323 发表于 2009-10-28 11:56

回复 #2 liaosnet 的帖子

关键是我现在没有介质。。。。

antyison 发表于 2009-10-28 13:41

=================================
                            MACHINE SPECIFIC NOTES
                                    FOR
               IBM Informix Dynamic Server 11.50.FC4 PRODUCT RELEASE
                           ON SUN SOLARIS 64bit
                               DATE: 14 Apr 2009
                      =================================

Kernel Parameters

    a) The values of the kernel parameters that were used for testing this
       product on Solaris 9 systems are given below. These values might need
       to be tuned depending on the application and availability of system
       resources. These entries are in /etc/system.

       set semsys:seminfo_semmap=64   
       set semsys:seminfo_semmni=4096
       set semsys:seminfo_semmns=4096
       set semsys:seminfo_semmnu=4096
       set semsys:seminfo_semume=64
       set semsys:seminfo_semmsl=500
       set shmsys:shminfo_shmmax=4398046511104
       set shmsys:shminfo_shmmin=100
       set shmsys:shminfo_shmmni=500
       set shmsys:shminfo_shmseg=100

       The value of the kernel parameter "semmsl" should be set to at least
       100. This is the maximum number of semaphores per set.

    b) On Solaris 10, all System V IPC facilities are either automatically
       configured or can be controlled by resource controls.

       The following kernel parameters are either removed from or commented
       out in the /etc/system file:

         semsys:seminfo_semmap
         semsys:seminfo_semmns
         semsys:seminfo_semmnu
         semsys:seminfo_semume
         shmsys:shminfo_shmmin
         shmsys:shminfo_shmseg

       The following IPC tunables are obsolete and are replaced by new resource
       controls:

         semsys:seminfo_semmsl
         semsys:seminfo_semmni
         shmsys:shminfo_shmmax
         shmsys:shminfo_shmmni

       The resource controls that replaced the obsolete IPC tunables listed
       above have the following default values on Solaris 10:

         process.max-sem-nsems    512
         project.max-sem-ids      128
         project.max-shm-memory   1/4 of physical memory
         project.max-shm-ids      128   

       Note that the project.max-shm-memory resource control limits the
       total amount of shared memory of one project, whereas previously,
       the shmsys:shminfo_shmmax parameter limited the size of a single
       shared memory segment.

       On systems that have zones enabled, zone-wide resource controls are
       specified in the zone configuration.

       Refer to the rctladm(1m) man page for more information about
       available resource controls.

       Examples:

       1. To display the current value of project.max-shm-memory set to the
          project and system wide, where IDS is running under the default
          project, run this command:

          # prctl -n project.max-shm-memory -i project default

       2. To display the values of all the resource controls for a specific
          IDS process, run this command:
         
          # prctl <oninit pid>

       3. To set the value of project.max-shm-memory for the project default
          to 4 TB without restarting the system, run this command:

          # prctl -n project.max-shm-memory -r -v 4tb -i project default

       4. To perform the same action as in example 3, but instead use
          the projmod command to modify the attribute value for
          project.max-shm-memory in /etc/project the local source of
          project information file, run this command:

          # projmod -a -K 'project.max-shm-memory=(priv,4TB,deny)' default

    c) IDS Failure with a Large Intimate Shared Memory Page Size

       On certain hardware configurations, Solaris 10 can use very large
       memory pages for Solaris Intimate Shared Memory (ISM): 32 MB or
       256 MB instead of the previous limit of 4 MB. IDS uses Solaris ISM
       for shared memory segments that are forced to be memory-resident by
       the RESIDENT configuration parameter, however IDS might experience
       problems if 32 MB or 256 MB pages are used by Solaris (APAR
       36804462).

       If you receive a message that contiguous shared memory segment
       allocation failed and the value of the SHMBASE configuration
       parameter is the same as its value in onconfig.std, then IDS might
       fail unexpectedly. To prevent this problem, set the Solaris 10
       operating system mmu_ism_pagesize configuration parameter to limit
       the memory pages to 4 MB for ISM. To set this parameter, edit the
       /etc/system file and add the following line:

         set mmu_ism_pagesize = 4194304

       Then restart the Solaris computer.

jl8323 发表于 2009-10-28 14:13

回复 #4 antyison 的帖子

3ks a lot :em09:
页: [1]
查看完整版本: ids11.5 for solaris install