brocade 48k交换机扩容端口板和路由板
1、 准备工作，扩容前准备好扩容所需备件。2块48口端口板，2块FR4-18i路由板，4个电源模块，防静电环，十字螺丝刀
---------------------------------------扩容前------------------------------------------------
B48K:admin> slotshow
Slot Blade Type ID Status
---------------------------------
1 SW BLADE 36 ENABLED
2 SW BLADE 36 ENABLED
3 SW BLADE 36 ENABLED
4 SW BLADE 36 ENABLED
5 CP BLADE 16 ENABLED
6 CP BLADE 16 ENABLED
7 SW BLADE 36 ENABLED
8 UNKNOWN VACANT
9 UNKNOWN VACANT
10 UNKNOWN VACANT
B48K:admin>
B48K:admin> psshow
Power Supply #1 is OK
DELTA DPS1001AB-1EM 23020000603 01 FL2L9024956
Power Supply #2 is OK
DELTA DPS1001AB-1EM 23020000603 01 FL2L9024962
Power Supply #3 is absent
Power Supply #4 is absent
B48K:admin>
---------------------------------------硬件扩容----------------------------------------------
1、 由于要使用FR4-18i板，所以必须先扩容Power Supply 3,4。
2、 扩容8号slot 48口端口板
3、 扩容10号solot FR4-18i板
---------------------------------------扩容后------------------------------------------------
1、在线扩容2个电源模块后，登陆交换机查看信息
B48K:admin> psshow
Power Supply #1 is OK
DELTA DPS1001AB-1EM 23020000603 01 FL2L9024956
Power Supply #2 is OK
DELTA DPS1001AB-1EM 23020000603 01 FL2L9024962
Power Supply #3 is OK
DELTA DPS1001AB-1EM 23020000603 03 FL2L945DD14
Power Supply #4 is OK
DELTA DPS1001AB-1EM 23020000603 02 FL2L945DBDB
B48K:admin>
2、在线扩容48口端口板及路由板后
B48K:admin> slotshow
Slot Blade Type ID Status
---------------------------------
1 SW BLADE 36 ENABLED
2 SW BLADE 36 ENABLED
3 SW BLADE 36 ENABLED
4 SW BLADE 36 ENABLED
5 CP BLADE 16 ENABLED
6 CP BLADE 16 ENABLED
7 SW BLADE 36 ENABLED
8 SW BLADE 36 DIAG RUNNING POST1
9 UNKNOWN VACANT
10 AP BLADE 24 DIAG RUNNING POST2
B48K:admin>
此时可以看到板卡正在自动跑POST。使用switchshow会看到48口端口板端口状态如下：
80 8 0 015000 id 4G No_Light TestingDisabled
81 8 1 015100 id 4G No_Light TestingDisabled
82 8 2 015200 id 4G No_Light TestingDisabled
83 8 3 015300 id 4G No_Light TestingDisabled
84 8 4 015400 id 4G No_Light TestingDisabled
85 8 5 015500 id 4G No_Light TestingDisabled
3、待POST完成后，新扩容板状态正常
B48K:admin> slotshow
Slot Blade Type ID Status
---------------------------------
1 SW BLADE 36 ENABLED
2 SW BLADE 36 ENABLED
3 SW BLADE 36 ENABLED
4 SW BLADE 36 ENABLED
5 CP BLADE 16 ENABLED
6 CP BLADE 16 ENABLED
7 SW BLADE 36 ENABLED
8 SW BLADE 36 ENABLED
9 UNKNOWN VACANT
10 AP BLADE 24 ENABLED
B48K:admin>
48口端口板POST时间大概在2个小时左右，FR4-18i板POST时间大概30分钟。
4、查看FR4-18i路由板firmware如下
B48K:admin> firmwareshow
Slot Name Appl Primary/Secondary Versions Status
------------------------------------------------------------------------
5CP0 FOS v5.3.0c STANDBY
v5.3.0c
6CP1 FOS v5.3.0c ACTIVE *
v5.3.0c
10FR4-18iFOS v5.3.0c
v5.3.0c
B48K:admin>
在将FR4-18i路由板插入到交换机后，FR4-18i板卡会自动从CP板download firmware。在messages中会看到如下信息：
2010/05/27-00:16:42, , 2765,, WARNING, SilkWorm48000, Firmware is being downloaded to the blade in slot 10.
Type <CR> to continue, Q<CR> to stop:
2010/05/27-00:16:40, , 2764,, INFO, SilkWorm48000, Connection established between CP and blade in slot 10.
Type <CR> to continue, Q<CR> to stop:
2010/05/27-00:15:46, , 2763,, INFO, B48K, Four power supplies are now required for 2X redundancy, Switch Status Policy values changed.
Type <CR> to continue, Q<CR> to stop:
2010/05/27-00:15:42, , 2762,, INFO, SilkWorm48000, FRU Slot 10 insertion detected.
Type <CR> to continue, Q<CR> to stop:
5、新加的FR4-18i路由板需要到brocade网站申请license，否则看到该板卡端口为Disabled (Persistent)状态
112 10 0 017000 id N4 No_Light Disabled (Persistent)
113 10 1 017100 id N4 No_Light Disabled (Persistent)
114 10 2 017200 id N4 No_Light Disabled (Persistent)
115 10 3 017300 id N4 No_Light Disabled (Persistent)
116 10 4 017400 id N4 No_Light Disabled (Persistent)
117 10 5 017500 id N4 No_Light Disabled (Persistent)
6、license申请方法
登陆https://www.switchkeyactivation.com/slkInternet/brocade网站，brocade license是与交换机WWN/Serial Number所绑定的，需要和随机附带的license盘中的Transaction Key到上述网站申请。所以在申请前请反复好核对好交换机的WWN和Serial Number，避免申请错误。
7、将申请的license添加到交换机
B48K:admin> licenseadd "b9dQS9bQbScIeRTu"
adding license-key
B48K:admin>
B48K:admin> licenseshow
bQeSzScRdecRfT03:
Web license
cSQbzdddezdTRc0j:
Zoning license
zSzQdSced0T0ReM:
Fabric license
b9dQS9bQbSeAeRTo:
Fabric Watch license
b9dQS9bQbSgAeRTq:
Performance Monitor license
b9dQS9bQbSkAeRTu:
Trunking license
b9dQS9bQbScIeRTu:
High-Performance Extension over FCIP/FC license
B48K:admin>
8、将FR4-18i端口从Disabled (Persistent)状态改为正常状态
B48K:admin> portcfgpersistentenable 10/0
B48K:admin>
更改后状态如下：
112 10 0 017000 id N4 No_Light 上传PDF文档供大家下载，谢谢！ 顶，谢谢分享~~~~ 不错，学习一下. 好贴收藏 写的很好啊 学习，收藏了:em27: :em03: 回复 1# asx_liu
:em03: 正需要呢 呵呵有没有级联扩容的文档啊 好东西