HP9000 IP配置后运行速度变慢
本来运行地好好的 后来公司改了网段 重新配置IP后 无论是登陆还是使用SAM等命令 都要等很长时间屏幕才回有输出，求解救！ 是不是配置了dns啊 检查/etc/hosts里面主机名对应的IP是否改正确了？还有/etc/nsswitch.conf里面host那一行用files在dns前面（如果用dns的话），如下面：hosts: files dns
先谢了，我试试看:em27::em27: # ls
#hosts inetd pvchange
#pam_user.conf inetd.conf pvcreate
.java inetd.conf.old pvdisplay
.pwd.lock inetsvcs.conf pvmove
MANPATH init pwck
PATH inittab quot
SHLIB_PATH insf quotacheck
SnmpAgent.d install quotaoff
TIMEZONE ioconfig quotaon
X11 ioctl.syscon rarpd.conf
acct ioinit rc.config
aliases ioscan rc.config.d
arp iscan rc.log
asx issue rc.log.old
audeventstab itemap rdump
audomon kbdlang reboot
auto_master killall repquota
auto_parms.log labelit resolv.conf
auto_parms.log.old lanconfig restore
backup lanscan rmboot
backup.cfg last rmsf
bcheckrc lastb rmt
bootpd link rmtab
bootpquery linkloop route
bootptab local rpc
boottab lp rrestore
btmp lsdev sam
catman lssf savecore
checklist lvchange sbtab
chroot lvcreate scsictl
clri lvdisplay services
cmcluster lvextend services.window
conf lvlnboot set_parms
config lvmconf setboot_tests
convertfs lvmmigrate setmnt
copyright lvmrc setprivgrp
cron lvmtab sfd.pid
csh.login lvreduce shutdown
cue.dm lvremove shutdown.allow
d.cshrc lvrmboot shutdownlog
d.exrc magic skel
d.login mail smtpd
d.profile mediainit snmpd
dce.clean mkboot snmpd.conf
dce.rm mkfs stcp.conf
dce.unconfig mklost+found swapinfo
dce_com_env mknod swapon
dce_com_utils mksf switch
dce_config mnttab syncer
dce_config_env motive.conf sysdef
dce_config_utils mount syslog.conf
dcopy mrouted.conf syslog.pid
default msmod syslogd
devnm mvdir tar
diskinfo named telnetd
disksecn named-xfer termcap
disktab ncheck translate
dmesg net tsconvert
dpp netconfig ttytype
dt netfmt tunefs
dump netgroup umount
dumpdates netid unlink
edquota nettl ups_conf
eisa nettlgen.conf ups_mond
eisa_config networks utmp
ems_inittab.old newfs utmpx
envd nsswitch.compat uucp
envd.conf nsswitch.files uucpd
extendfs nsswitch.hp_defaultsvgcfgbackup
fbackup nsswitch.ldap vgcfgrestore
fbackuprdr nsswitch.nis vgchange
fbackupwrtr nsswitch.nisplus vgcreate
ff ntp.conf vgdisplay
frecover ocd vgexport
freeze ocdebug vgextend
fsck oldnettlgen.conf vgimport
fsclean opt vgreduce
fsdb pam.conf vgremove
fstab pam.krb5 vgscan
ftpd pam.ldap vhelp
fuser pam.ldap.trusted volcopy
gated.conf pam_user.conf vtdaemon
getty passwd vtdaemonlog
gettydefs ping vtgateway
getx25 power_onoff vtserver
group powerfail vue
grpck powerfail.cfg vx
gss ppp wall
hba.conf pre_init_rc whodo
hosts prmconf wtmp
hosts.old profile ximian
hpC2400 protocols xtab
hparray ptydaemon yp
ifconfig ptydaemonlog ypbind
ifconfig.muxids publickey zoneinfo
# more nsswitch.files
#
# /etc/nsswitch.files:
#
# @(#)B.11.11_LR
#
# An example file that could be copied over to /etc/nsswitch.conf; it
# does not use any name services.
#
passwd: files
group: files
hosts: files
services: files
networks: files
protocols: files
rpc: files
publickey: files
netgroup: files
automount: files
aliases: files
貌似没有nsswitch.conf是在files后面加dns么
host对应的IP是正确的 more /etc/hosts
然后nslookup hosts # more /etc/hosts
## Configured using SAM by root on Wed May 11 16:22:05 2011
## Configured using SAM by root on Mon May 30 13:40:35 2011
# @(#)B.11.11_LRhosts $Revision: 1.9.214.1 $ $Date: 96/10/08 13:20:01 $
#
# The form for each entry is:
# <internet address> <official hostname> <aliases>
#
# For example:
# 192.1.2.34 hpfcrmloghost
#
# See the hosts(4) manual page for more information.
# Note: The entries cannot be preceded by a space.
# The format described in this file is the correct format.
# The original Berkeley manual page contains an error in
# the format description.
#
127.0.0.1 localhost loopback
172.30.12.30 L1000
:em27::em27:
# nslookup hosts
*** Can't find server name for address 172.30.12.254: Timed out
*** Default servers are not available
Using /etc/hosts on:L1000
looking up FILES
*** No address information is available for "hosts"
这是什么呢 出错了？:em29::em29: #cp /etc/nsswitch.files /etc/nsswitch.conf
页:
[1]