lgatuk
发表于 2014-01-13 08:25
回复 10# lbseraph
mark一下 收藏
woailili9
发表于 2014-01-13 11:17
回复 10# lbseraph
十分感谢
woailili9
发表于 2014-01-13 13:44
回复 10# lbseraph
还有请问下版主 在MP里面可以将分区设置为开机加电不自动启动的么?
有的话请问是哪个里面我查了下MP的常用命令好像没找到这个啊
lbseraph
发表于 2014-01-13 14:17
回复 13# woailili9
低端点的小机是PR这个MP命令,你查一下rx8640的是不是也是这个。我手头没Cell的机器,你不行就MP:CM> help里面挨个找一下,这个是属于power restore policy的。
lgatuk
发表于 2014-01-13 14:35
回复 14# lbseraph
HE:hpiLO-> li
li
==== MP Help: Command Menu List =============================================
BLADE: Display BLADE parameters PC: Remote Power Control
CA: Configure asynch/serial ports PM: Power Management
DATE: Display Date PR: Power Restore Configuration
DC: Default Configuration PS: Power management module Status
DI: DIsconnect users RS: Reset System through RST signal
DF: Display FRU Information SA: Set MP Access
DNS : Configure DHCP and DNS SO: Security Options
FW: Upgrade MP firmware SS: System processors Status
HE: Display Help SYSREV: Display System firmware Revs.
ID: System Information SYSSET: System Settings
IT: Modify MP inactivity timeouts TC: Reset system via INIT
LC: Configure LAN, SSH and Web portsTE: TEll- send a msg. to other users
LDAP: Configure Directory parameters UC: User Configuration
LM: License Management WHO : Display connected MP users
LOC : Locator UID LEDs display WOL : Wake-On-LAN
LS: LAN Status WSMAN : WSMAN notification settings
NPAR : nPartition Configuration XD: Diagnostics and reset of MP
OEMSYSSET: OEM System Settings
lbseraph
发表于 2014-01-13 14:41
lgatuk 发表于 2014-01-13 14:35 static/image/common/back.gif
PR: Power Restore Configuration
不过你这个是Blade的机器吧?:wink:
lgatuk
发表于 2014-01-13 15:34
回复 16# lbseraph
厉害
8640得去机房看 现在没有时间 改天传上来
woailili9
发表于 2014-01-13 20:29
十分感谢以上两位的热心帮助谢谢!!!
woailili9
发表于 2014-01-14 09:44
回复 16# lbseraph
一开始情况(1月12日更换CPU之前)
MP:VWR (<cr>,<sp>,+,-,?,F,L,J,D,K,R,T,A,C,U,^B) >
32267 SFW0,0,02 4b001d3500e008e8 01000000524a5077 MEM_NON_DEST_TEST
32267 10/01/2013 04:32:55
32266 SFW0,0,0 *3 648015b500e008e6 00ffff0001ffff15 BOOT_CPU_DECONFIG_NO_POWER
32266 10/01/2013 04:32:55
32265 SFW0,0,0 *3 648015b500e008e4 00ffff0001ffff15 BOOT_CPU_DECONFIG_NO_POWER
32265 10/01/2013 04:32:55
32264 SFW0,0,0 *3 6480087500e008e2 00ffff0001ffff15 BOOT_CPU_DECONFIG
32264 10/01/2013 04:32:55
32263 SFW0,0,0 *3 648015b500e008e0 00ffff0001ffff15 BOOT_CPU_DECONFIG_NO_POWER
32263 10/01/2013 04:32:55
32262 SFW0,0,0 *3 648015b500e008de 00ffff0001ffff15 BOOT_CPU_DECONFIG_NO_POWER
32262 10/01/2013 04:32:55
32261 SFW0,0,0 *3 6480087500e008dc 00ffff0001ffff15 BOOT_CPU_DECONFIG
32261 10/01/2013 04:32:55
32260 SFW0,0,0 *3 648015b500e008da 00ffff0001ffff15 BOOT_CPU_DECONFIG_NO_POWER
32260 10/01/2013 04:32:44
32259 SFW0,0,0 *3 648015b500e008d8 00ffff0001ffff15 BOOT_CPU_DECONFIG_NO_POWER
32259 10/01/2013 04:32:44
32258 SFW0,0,0 *3 6480087500e008d6 00ffff0001ffff15 BOOT_CPU_DECONFIG
32258 10/01/2013 04:32:44
32257 SFW0,0,02 5680110b00e008d4 0000000000000003 BOOT_INFO_REGARDING_CPU_NUM
32257 10/01/2013 04:32:44
Log Entry 32266: 10/01/2013 04:32:55
Alert level 3:Warning
Keyword:BOOT_CPU_DECONFIG_NO_POWER
Firmware is deconfiguring a CPU due to no power to CPU.The physical location o
Reporting Entity:System Firmware located in cabinet 0, slot 0, cpu 0
Physical Location:Processor source detail 0x5 cabinet 0 cell 0
0x648015b500e008e6 0x00ffff0001ffff15
0x6b0015b500e008e7 0x01000000524a5077
MP:VWR (<cr>,<sp>,+,-,?,F,L,J,D,K,R,T,A,C,U,^B) >
Log Entry 32265: 10/01/2013 04:32:55
Alert level 3:Warning
Keyword:BOOT_CPU_DECONFIG_NO_POWER
Firmware is deconfiguring a CPU due to no power to CPU.The physical location o
Reporting Entity:System Firmware located in cabinet 0, slot 0, cpu 0
Physical Location:Processor source detail 0x5 cabinet 0 cell 0
0x648015b500e008e4 0x00ffff0001ffff15
0x6b0015b500e008e5 0x01000000524a5077
MP:CM> ps
Display detailed status of the selected MP bus device.
The following MP bus devices were found:
+---+----+-----+-------+-------+-----------+
| | | | | | |
| | | Sys | |IO | Bulk Pwr|
|Cab| MP |Bkpln| Cells |Chassis| Supplies|
| # |MS| |0 1 2 3| 0 1 |0 1 2 3 4 5|
+---+----+-----+-------+-------+-----------+
| 0 |**|*|* * * *| * * |* * * * * *|
| 8 |**|*|- - - -| * * |* * - - - -|
+---+----+-----+-------+-------+-----------+
You may display detailed power and hardware status for the following items:
T - Cabinet
S - System Backplane
G - MP (Core I/O)
P - IO Chassis
C - Cell
Select Device: g
HW status for MP : No Fault Detected
Complex model string: 9000/800/rp8440
MP is not failed over
Cabinet LED is Green
Battery state is good
Last MP software reset occurred WED FEB 01 00:40:33 2051
MP firmware rev B.002.005.012 built on Aug 23 2007 14:34:46
MP:CM>
MP:CM> ps
Display detailed status of the selected MP bus device.
The following MP bus devices were found:
+---+----+-----+-------+-------+-----------+
| | | | | | |
| | | Sys | |IO | Bulk Pwr|
|Cab| MP |Bkpln| Cells |Chassis| Supplies|
| # |MS| |0 1 2 3| 0 1 |0 1 2 3 4 5|
+---+----+-----+-------+-------+-----------+
| 0 |**|*|* * * *| * * |* * * * * *|
| 8 |**|*|- - - -| * * |* * - - - -|
+---+----+-----+-------+-------+-----------+
You may display detailed power and hardware status for the following items:
T - Cabinet
S - System Backplane
G - MP (Core I/O)
P - IO Chassis
C - Cell
Select Device: t
Enter cabinet number (0 or 8):
... Not a valid cabinet number for this device ...
Enter cabinet number (0 or 8): 0
HW status for rp8440 cabinet : NO FAILURE DETECTED
Master/Slave failover is Enabled
Power switch is on
Right Door is closed
Top Door is closed
Left Door is closed
Total Power Available 6000 VA
Total Power Needed 3527 VA
Power Redundancy : redundant
Power Viability : viable
Power Status
---------------+-----+-------+-------+-----------+
| | | | |
| Sys | |IO | Bulk Pwr|
|Bkpln| Cells |Chassis| Supplies|
| |0 1 2 3| 0 1 |0 1 2 3 4 5|
---------------+-----+-------+-------+-----------+
Populated |*|* * * *| * * |* * * * * *|
Enabled |*|* * * *| * * |* * * * * *|
Power OK |*|* * * *| * * |* * * * * *|
Warning/Fault | | | | |
Attention LED | | | | |
AC Line status:
Line A0 NOT PRESENT
Line B0 Present
Line A1 Present
Line B1 NOT PRESENT
-- Press <CR> to continue, or 'Q' to Quit --
Front Fan Speed : normal
Rear Fan speed : normal
I/O Bay Fan Speed : normal
Temperature state : normal
Main Fan Redundancy : redundant
I/O Fan Redundancy : redundant
Overtemp Shutdown Enabled
| BPS | PCI |
| Fans | Fans |
| 0 1 2 3 4 5 | 0 1 2 3 4 5 |
+-----------+-------------+-------------+
Populated | * * * * * * | * * * * * * |
Failing | | |
Failed | | |
| Standby/Main Fans |
| 1 1 1 1 1 1 1 1 1 1 2 |
| 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 |
+-----------+-------------------------------------------+
Populated | * * * * * * * * * * * * * * * * * * * * * |
Failing | |
Failed | |
|Cell Fans |
| CPU C |
| 0 1 2 3C |
+-----------+------------+
Cell 0 | |
Populated | * * * * |
Failing | |
Failed | |
Cell 1 | |
Populated | * * * * |
Failing | |
Failed | |
Cell 2 | |
Populated | * * * ** |
Failing | |
Failed | |
Cell 3 | |
Populated | * * * ** |
Failing | |
Failed | |
MP:CM>
MP:CM> ps
Display detailed status of the selected MP bus device.
The following MP bus devices were found:
+---+----+-----+-------+-------+-----------+
| | | | | | |
| | | Sys | |IO | Bulk Pwr|
|Cab| MP |Bkpln| Cells |Chassis| Supplies|
| # |MS| |0 1 2 3| 0 1 |0 1 2 3 4 5|
+---+----+-----+-------+-------+-----------+
| 0 |**|*|* * * *| * * |* * * * * *|
| 8 |**|*|- - - -| * * |* * - - - -|
+---+----+-----+-------+-------+-----------+
You may display detailed power and hardware status for the following items:
T - Cabinet
S - System Backplane
G - MP (Core I/O)
P - IO Chassis
C - Cell
Select Device: c
Enter cell number: 0
HW status for Cell 0 : NO FAILURE DETECTED
Power status : on, no fault
Faults above are latched. They are cleared just before the cell is powered on.
Boot is not blocked
PDH memory is shared
Processor Compatibility : OK
RIO cable status : connected
RIO cable connection physical location : PCI Domain 0
Core cell is cell 0
Attention Led is off
PDHC status Leds :***-
CPU Module Slot 0 1 2 3
Populated P P P
Local 48V Good * * *
Power Enabled * *
Power Good * *
(* - True, P - Processor, T - Terminator)
| DIMM Presence |
| |
| Side: | A | B |
|Echelon: |01234567|01234567|
+---------+--------+--------+
| |*** *** |
1 1 1 1 1 1
VRM's 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5
Present : * * * * * * * * * * * * * * * *
Enabled : * * * * * * * * * * * * * * * *
Pwr Good : * * * * * * * * * * * * * * * *
Front Side Bus Freq. : 267 MHz
CPU Core Freq. : 1068 MHz
CPU Part Number : PA8900
System Boot Rom (SFW) firmware rev 043.006.000
PDH controller (PDHC) firmware rev B.023.003.038 built WED APR 18 21:43:36 2007
1月12日更换CPU第一步骤:将新申请的CPU更换上CPU1。然后新更换上去的CPU不认。
HW status for Cell 0 : FAILURE DETECTED
Power status : on, no fault
Faults above are latched. They are cleared just before the cell is powered on.
Boot is blocked
PDH memory is not shared
Processor Compatibility : FAULT
RIO cable status : connected
RIO cable connection physical location : PCI Domain 0
Core cell is INVALID
Attention Led is off
PDHC status Leds :--*-
CPU Module Slot 0 1 2 3
Populated P P P
Local 48V Good * *
Power Enabled * *
Power Good * *
(* - True, P - Processor, T - Terminator)
| DIMM Presence |
| |
| Side: | A | B |
|Echelon: |01234567|01234567|
+---------+--------+--------+
| |*** *** |
1 1 1 1 1 1
VRM's 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5
Present : * * * * * * * * * * * * * * * *
Enabled : * * * * * * * * * * * * * * * *
Pwr Good : * * * * * * * * * * * * * * * *
Front Side Bus Freq. : 267 MHz
CPU Core Freq. : 1068 MHz
CPU Part Number : PA8900
System Boot Rom (SFW) firmware rev 043.006.000
PDH controller (PDHC) firmware rev B.023.003.038 built WED APR 18 21:43:36 2007
第二步骤:将新更换上去的1号CPU和2号CPU调换位置后:
MP:CM> ps
Display detailed status of the selected MP bus device.
The following MP bus devices were found:
+---+----+-----+-------+-------+-----------+
| | | | | | |
| | | Sys | |IO | Bulk Pwr|
|Cab| MP |Bkpln| Cells |Chassis| Supplies|
| # |MS| |0 1 2 3| 0 1 |0 1 2 3 4 5|
+---+----+-----+-------+-------+-----------+
| 0 |**|*|* * * *| * * |* * * * * *|
| 8 |**|*|- - - -| * * |* * - - - -|
+---+----+-----+-------+-------+-----------+
You may display detailed power and hardware status for the following items:
T - Cabinet
S - System Backplane
G - MP (Core I/O)
P - IO Chassis
C - Cell
Select Device: c
Enter cell number: 0
HW status for Cell 0 : FAILURE DETECTED
Power status : on, no fault
Faults above are latched. They are cleared just before the cell is powered on.
Boot is blocked
PDH memory is not shared
Processor Compatibility : FAULT
RIO cable status : connected
RIO cable connection physical location : PCI Domain 0
Core cell is INVALID
Attention Led is off
PDHC status Leds :--*-
CPU Module Slot 0 1 2 3
Populated P P P
Local 48V Good * * *
Power Enabled * * *
Power Good * * *
(* - True, P - Processor, T - Terminator)
| DIMM Presence |
| |
| Side: | A | B |
|Echelon: |01234567|01234567|
+---------+--------+--------+
| |*** *** |
1 1 1 1 1 1
VRM's 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5
Present : * * * * * * * * * * * * * * * *
Enabled : * * * * * * * * * * * * * * * *
Pwr Good : * * * * * * * * * * * * * * * *
Front Side Bus Freq. : 267 MHz
CPU Core Freq. : 1068 MHz
CPU Part Number : PA8900
System Boot Rom (SFW) firmware rev 043.006.000
PDH controller (PDHC) firmware rev B.023.003.038 built WED APR 18 21:43:36 2007
MP:CM>
MP:CM> ps
Display detailed status of the selected MP bus device.
The following MP bus devices were found:
+---+----+-----+-------+-------+-----------+
| | | | | | |
| | | Sys | |IO | Bulk Pwr|
|Cab| MP |Bkpln| Cells |Chassis| Supplies|
| # |MS| |0 1 2 3| 0 1 |0 1 2 3 4 5|
+---+----+-----+-------+-------+-----------+
| 0 |**|*|* * * *| * * |* * * * * *|
| 8 |**|*|- - - -| * * |* * - - - -|
+---+----+-----+-------+-------+-----------+
You may display detailed power and hardware status for the following items:
T - Cabinet
S - System Backplane
G - MP (Core I/O)
P - IO Chassis
C - Cell
Select Device: c
Enter cell number: 1
HW status for Cell 1 : FAILURE DETECTED
Power status : on, no fault
Faults above are latched. They are cleared just before the cell is powered on.
Boot is blocked
PDH memory is shared
Processor Compatibility : OK
RIO cable status : connected
RIO cable connection physical location : PCI Domain 1
Core cell is INVALID
Attention Led is off
PDHC status Leds :-***
CPU Module Slot 0 1 2 3
Populated P P P
Local 48V Good * * *
Power Enabled * * *
Power Good * * *
(* - True, P - Processor, T - Terminator)
| DIMM Presence |
| |
| Side: | A | B |
|Echelon: |01234567|01234567|
+---------+--------+--------+
| |*** *** |
1 1 1 1 1 1
VRM's 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5
Present : * * * * * * * * * * * * * * * *
Enabled : * * * * * * * * * * * * * * * *
Pwr Good : * * * * * * * * * * * * * * * *
Front Side Bus Freq. : 267 MHz
CPU Core Freq. : 1068 MHz
CPU Part Number : PA8900
System Boot Rom (SFW) firmware rev 043.006.000
PDH controller (PDHC) firmware rev B.023.003.038 built WED APR 18 21:43:36 2007
U: Unfiltered
MP:VWR (<cr>,<sp>,+,-,?,F,L,J,D,K,R,T,A,C,U,^B) >
32609 SFW0,1,02 4b001d3510e00b83 0100000052d16831 MEM_NON_DEST_TEST
32609 01/11/2014 15:50:09
32608 SFW0,1,02 4380149b10e00b81 0000000000000003 BOOT_RESET_HCELL_TYPE
32608 01/11/2014 15:49:32
32607 SFW0,1,02 4380149a10e00b7f 00000782ff81cbc8 BOOT_RESET_HCELL_CALLER
32607 01/11/2014 15:49:32
32606 SFW0,1,0 *3 7780126310e00b7d 0000000000000000 BOOT_FIND_CORE_CELL_CONFIG_SELECT_ERR
32606 01/11/2014 15:49:32
32605 SFW0,1,0 *3 63800a5510e00b7b 0000000000000002 BOOT_PD_RENDEZ_TIMEOUT
32605 01/11/2014 15:49:27
32604 SFW0,2,02 4b001d3520e00b7a 0100000052d1655b MEM_NON_DEST_TEST
32604 01/11/2014 15:38:03
32603 SFW0,3,02 4b001d3530e00b79 0100000052d1655b MEM_NON_DEST_TEST
32603 01/11/2014 15:38:03
32602 SFW0,1,02 4b001d3510e00b78 0100000052d1654f MEM_NON_DEST_TEST
32602 01/11/2014 15:37:51
32601 PDHC 0,3 2 4480198703e00b76 00ffff03ff04ff12 CC_FAN_OK
32601 01/11/2014 15:37:33
32600 PDHC 0,2 2 4480198702e00b74 00ffff02ff04ff12 CC_FAN_OK
32600 01/11/2014 15:37:31
32599 PDHC 0,1 2 4480198701e00b72 00ffff01ff04ff12 CC_FAN_OK
32599 01/11/2014 15:37:29
32591 PDHC 0,0 *7 f680112400e00b62 0000000000000008 PDHC_CELL_INCOMPATIBLE
32591 01/11/2014 15:37:10
32590 MP 0 2 44800ee700e00b60 00ffffffff01ff68 CELL_ON
32590 01/11/2014 15:37:09
32589 MP 0 2 44800ee700e00b5e 00ffffffff00ff68 CELL_ON
32589 01/11/2014 15:37:08
32588 MP 0 2 44801cf200e00b5c 0000ffffffffff43 IOBP_PWR_REDUNDANT
32588 01/11/2014 15:37:07
32587 MP 0 2 448019da00e00b5a 000000ffffffff69 IOBP_ON
32587 01/11/2014 15:37:07
32586 MP 0 2 44801cf200e00b58 0000ffffffffff43 IOBP_PWR_REDUNDANT
32586 01/11/2014 15:37:07
32585 MP 0 2 448019da00e00b56 000001ffffffff69 IOBP_ON
32585 01/11/2014 15:37:07
32584 CLU0 2 4480194800e00b54 00ffffffff00ff60 SYS_BKP_CLK_HSO2RCS_GOOD
32584 01/11/2014 15:37:07
32583 CLU0 2 4480194800e00b52 00ffffffff01ff60 SYS_BKP_CLK_HSO2RCS_GOOD
32583 01/11/2014 15:37:07
32582 MP 0 2 448019d800e00b50 000000ffffffff69 MAIN_BP_ON
32582 01/11/2014 15:37:07
32581 MP 8 2 44801cf208e00b4e 0800ffffffffff43 IOBP_PWR_REDUNDANT
32581 01/11/2014 15:36:57
32580 MP 8 2 448019da08e00b4c 080000ffffffff69 IOBP_ON
32580 01/11/2014 15:36:57
32579 MP 8 2 44801cf208e00b4a 0800ffffffffff43 IOBP_PWR_REDUNDANT
32579 01/11/2014 15:36:57
32578 MP 8 2 448019da08e00b48 080001ffffffff69 IOBP_ON
32578 01/11/2014 15:36:57
32577 MP 8 2 448019d808e00b46 080000ffffffff69 MAIN_BP_ON
32577 01/11/2014 15:36:57
MP:VWR (<cr>,<sp>,+,-,?,F,L,J,D,K,R,T,A,C,U,^B) >
32576 PDHC 0,3 2 448013c303e00b44 00ffff03ffffff94 CELL_EJECTORS_LATCHED
32576 01/11/2014 15:35:08
32575 PDHC 0,2 2 448013c302e00b42 00ffff02ffffff94 CELL_EJECTORS_LATCHED
32575 01/11/2014 15:35:07
32574 PDHC 0,1 2 448013c301e00b40 00ffff01ffffff94 CELL_EJECTORS_LATCHED
32574 01/11/2014 15:35:06
32573 PDHC 0,0 *7 f680112400e00b3e 0000000000000008 PDHC_CELL_INCOMPATIBLE
32573 01/11/2014 15:35:05
32572 PDHC 0,0 2 448013c300e00b3c 00ffff00ffffff94 CELL_EJECTORS_LATCHED
32572 01/11/2014 15:35:05
32571 PDHC 0,3 2 568019d303e00b3a 0000000000000000 PDHC_INFO
32571 01/11/2014 15:35:05
32570 PDHC 0,3 2 568019d303e00b38 003c73b8002513f0 PDHC_INFO
32570 01/11/2014 15:35:05
32569 PDHC 0,3 2 568019d303e00b36 0000020b00000005 PDHC_INFO
32569 01/11/2014 15:35:05
32568 PDHC 0,3 2 568019d303e00b34 003c71a800261544 PDHC_INFO
32568 01/11/2014 15:35:05
32567 PDHC 0,3 2 568019d303e00b32 000000b700000005 PDHC_INFO
32567 01/11/2014 15:35:05
32566 PDHC 0,3 2 568019d303e00b30 003ca32400249548 PDHC_INFO
32566 01/11/2014 15:35:05
MP MAIN MENU:
CO: Consoles
VFP: Virtual Front Panel
CM: Command Menu
CL: Console Logs
SL: Show Event Logs
FW: Firmware Update
HE: Help
X: Exit Connection
MP> co
Partitions available:
# Name
-------
0)Partition 0 - UX
1)Partition 1 - UX
2)Partition 2 - UX
Q)Quit
Please select partition number: 0
Connecting to OS Console: Partition 0 - UX
(Use <Ctrl-b> to return to main menu.)
- - - - - - - - - - Prior Console Output - - - - - - - - - -
1A 0xffffc0f4000Cpu configured, not flagged to be deconfigured
1B 0xffffc0f5000Cpu configured, not flagged to be deconfigured
2A 0xffffc0f8000Cpu configured, not flagged to be deconfigured
2B 0xffffc0f9000Cpu configured, not flagged to be deconfigured
这种情况是不是CPU没换好呢?硬件没换好?
lbseraph
发表于 2014-01-14 16:41
回复 19# woailili9
你说的CPU是指整个Cell板吧?