wjxlcc 发表于 2013-01-05 14:33

请大家帮我看看是什么问题

lom>console
lom>screen not found.
Can't open input device.
Keyboard not present.Using ttya for input and output.

Netra t 1400/1405 (4 X UltraSPARC-II 440MHz), No Keyboard
OpenBoot 3.31, 4096 MB memory installed, Serial #51545403.
Ethernet address 0:3:ba:12:85:3b, Host ID: 8312853b.



Rebooting with command: boot                                          
Boot device: disk0:File and args:
SunOS Release 5.10 Version Generic_118822-18 64-bit
Copyright 1983-2005 Sun Microsystems, Inc.All rights reserved.
Use is subject to license terms.
WARNING: Error writing ufs log state
WARNING: ufs log for / changed state to Error
WARNING: Please umount(1M) / and run fsck(1M)
WARNING: Failed to install "power" driver.

panic/thread=180e000: mod_hold_stub: Couldn't load stub module misc/strplumb

000000000180b890 genunix:mod_hold_stub+1f0 (0, 185e000, 18a7bc8, 60000d268d0, 1817010, 0)
%l0-3: 0000000000000002 0000000000000004 0000000001854fbc 0000000000000000
%l4-7: 0000000000000000 0000000001854f94 0000000001854c00 0000000000000000
000000000180b940 unix:stubs_common_code+30 (0, 7c5b7, 18aa400, 18ad400, 11ddc00, 1819400)
%l0-3: 000000000180b209 000000000180b2e1 00000000ff000000 0000000000000001
%l4-7: 0000000000000000 0000000001817020 0000000000000000 0000060000d3f890
000000000180ba10 genunix:main+e8 (1813d08, 0, 1835b00, 18a7800, 180e000, 1813c00)
%l0-3: 0000000070002000 0000000000000001 000000000180c000 000000000180e000
%l4-7: 0000000000000001 0000000001072800 0000000000000060 0000000000000000

syncing file systems... done
skipping system dump - no dump device configured
rebooting...
Resetting ...

screen not found.
Can't open input device.
Keyboard not present.Using ttya for input and output.

Netra t 1400/1405 (4 X UltraSPARC-II 440MHz), No Keyboard
OpenBoot 3.31, 4096 MB memory installed, Serial #51545403.
Ethernet address 0:3:ba:12:85:3b, Host ID: 8312853b.



Rebooting with command: boot                                          
Boot device: disk0:File and args:
-
Type'go' to resume


已换cpu0后，还是报cpu0 panic；这次拆下cpu0后报cpu1 panic，换回旧cpu0，还是报cpu0 panic；
>但用cdrom可以启动到单用户

znnnz 发表于 2013-01-05 14:35

@wjxlcc


既然已经串口了，就顺手做个最大化自检，排除了CPU内村官等，就是硬盘导致的panic了。

wjxlcc 发表于 2013-01-05 14:47

回复 2# znnnz


    客户那边没做最大化自检，会不会是主板有问题。

znnnz 发表于 2013-01-05 14:55

@wjxlcc


主板可能性最小

wjxlcc 发表于 2013-01-05 14:57

回复 4# znnnz


    嗯知道了 谢谢大哥了

东方蜘蛛 发表于 2013-01-05 17:48

先做POST，没问题就是OS有问题。
页: [1]
查看完整版本: 请大家帮我看看是什么问题