ko模块加载后，UBI文件系统出错~UBI error: ubi_io_read: error -1 跪求解！！！
在linux系统中装载ko模块驱动后，出现ubi_error, 求解：atmel_nand atmel_nand: Too many error.
atmel_nand atmel_nand: Too many error.
atmel_nand atmel_nand: Too many error.
atmel_nand atmel_nand: Too many error.
UBI error: ubi_io_read: error -1 while reading 2828 bytes from PEB 37:63024, rea
d 464 bytes
UBIFS error (pid 34: try_read_node: cannot read node type 1 from LEB 35:58928,
error -1
atmel_nand atmel_nand: Too many error.
atmel_nand atmel_nand: Too many error.
atmel_nand atmel_nand: Too many error.
atmel_nand atmel_nand: Too many error.
UBI error: ubi_io_read: error -1 while reading 2828 bytes from PEB 37:63024, rea
d 464 bytes
UBIFS error (pid 34: ubifs_read_node: cannot read node 1 from LEB 35:58928, er
ror -1
UBIFS error (pid 34: do_readpage: cannot read page 55 of inode 1212, error -1
atmel_nand atmel_nand: Too many error.
atmel_nand atmel_nand: Too many error.
atmel_nand atmel_nand: Too many error.
atmel_nand atmel_nand: Too many error.
UBI error: ubi_io_read: error -1 while reading 2828 bytes from PEB 37:63024, rea
d 464 bytes
UBIFS error (pid 34: try_read_node: cannot read node type 1 from LEB 35:58928,
error -1
atmel_nand atmel_nand: Too many error.
atmel_nand atmel_nand: Too many error.
atmel_nand atmel_nand: Too many error.
atmel_nand atmel_nand: Too many error.
UBI error: ubi_io_read: error -1 while reading 2828 bytes from PEB 37:63024, rea
d 464 bytes
UBIFS error (pid 34: ubifs_read_node: cannot read node 1 from LEB 35:58928, er
ror -1
UBIFS error (pid 34: do_readpage: cannot read page 55 of inode 1212, error -1
This is driver release
Bus error
atmel_nand atmel_nand: Too many error.
UBIFS error (pid 340): ubifs_read_node: bad node type (125 but expected 9)
UBIFS error (pid 340): ubifs_read_node: bad node at LEB 49:56024, LEB mapping st
atus 1
UBIFS error (pid 340): ubifs_iget: failed to read inode 174, error -22
UBIFS error (pid 340): ubifs_lookup: dead directory entry '.ash_history', error
-22
UBIFS warning (pid 340): ubifs_ro_mode: switched to read-only mode, error -22
UBIFS error (pid 340): ubifs_read_node: bad node type (181 but expected 9)
UBIFS error (pid 340): ubifs_read_node: bad node at LEB 44:6336, LEB mapping sta
tus 1
UBIFS error (pid 340): do_readpage: cannot read page 5 of inode 133, error -22
UBIFS error (pid 340): ubifs_read_node: bad node type (181 but expected 9)
UBIFS error (pid 340): ubifs_read_node: bad node at LEB 44:6336, LEB mapping sta
tus 1
UBIFS error (pid 340): do_readpage: cannot read page 5 of inode 133, error -22
Configure net done
Set seaech library in /etc/profile
Set user path in /etc/profile
Configure environment done
UBIFS error (pid 352): ubifs_read_node: bad node type (16 but expected 9)
UBIFS error (pid 352): ubifs_read_node: bad node at LEB 44:6528, LEB mapping sta
tus 1
UBIFS error (pid 352): do_readpage: cannot read page 20 of inode 133, error -22
UBIFS error (pid 352): ubifs_read_node: bad node type (16 but expected 9)
UBIFS error (pid 352): ubifs_read_node: bad node at LEB 44:6528, LEB mapping sta
tus 1
UBIFS error (pid 352): do_readpage: cannot read page 20 of inode 133, error -22
Bus error
Load .ko module done
rm: can't remove '/dev/fpga': Read-only file system
mknod: /dev/fpga: File exists
Create device file done
This is driver open
fpga_write: Enter
fpga_write: fpga Image install is being processing@@@@@@ count(0x661edc)
iLen = 6692572
Fpga install done!
fpga_write: fpga Image install over @@@@@@
bspClock1Config: test len(26)clock1 reference clock source is EXT-10MHz
start to config clock1 ......clock unlock!
RRU_DEBUG##
页:
[1]