xujinjunWY 发表于 2014-04-10 10:36

刀片机出现橙色报警错误，日志如下，望各位大虾帮忙分析下，是什么原因导致的

0 I Audit 04/10/14 10:16:07 0x0000007a Remote login successful for user 'USERID' from Web at IP 192.168.70.111
1 I SERVPROC 04/10/14 10:05:46 0x00017108 Ethernet interface is now active.
2 E Blade_01 04/08/14 02:57:28 0x806f0212 (System Event) system hardware failure
3 I Blade_01 04/08/14 02:57:28 0x10000002 SYS F/W: Firmware. See procedure FSPSP04 then FSPSP06 (500C3897 B181F126 030000F0 53AE1510 C13920FF 400000FF 00000000 FFFFFFFF 00000000 00000000)
4 I Blade_01 04/08/14 02:57:28 0x806f0212 Recovery (System Event) system hardware failure
5 E Blade_01 03/31/14 16:57:08 0x806f0212 (System Event) system hardware failure
6 I Blade_01 03/31/14 16:57:08 0x10000002 SYS F/W: Firmware. See procedure FSPSP04 then FSPSP06 (500C0EDE B181F126 030000F0 53AE1510 C13920FF 400000FF 00000000 FFFFFFFF 00000000 00000000)
7 I Blade_01 03/31/14 16:57:08 0x806f0212 Recovery (System Event) system hardware failure
8 E Blade_01 03/24/14 06:56:47 0x806f0212 (System Event) system hardware failure
9 I Blade_01 03/24/14 06:56:47 0x10000002 SYS F/W: Firmware. See procedure FSPSP04 then FSPSP06 (500BE525 B181F126 030000F0 53AE1510 C13920FF 400000FF 00000000 FFFFFFFF 00000000 00000000)
10 I Blade_01 03/24/14 06:56:47 0x806f0212 Recovery (System Event) system hardware failure
11 E Blade_01 03/16/14 20:56:27 0x806f0212 (System Event) system hardware failure
12 I Blade_01 03/16/14 20:56:27 0x10000002 SYS F/W: Firmware. See procedure FSPSP04 then FSPSP06 (500BBB6C B181F126 030000F0 53AE1510 C13920FF 400000FF 00000000 FFFFFFFF 00000000 00000000)
13 I Audit 03/10/14 16:26:08 0x0001601a Remote logoff successful for user 'USERID' from Web at IP 192.168.70.111
14 I SERVPROC 03/10/14 16:21:16 0x00017109 Ethernet interface is no longer active.
15 I Audit 03/10/14 16:20:38 0x0001600b All system messages deleted from event log by 'USERID'.
16 I SERVPROC 03/10/14 16:20:38 0x00000071 Recovery Event log 75% full
17 I Audit 03/10/14 16:20:38 0x0001601b All audit messages deleted from event log by 'USERID'.

xujinjunWY 发表于 2014-09-04 10:55

回复 1# xujinjunWY


   

sellthetime 发表于 2014-09-10 09:00

看这些只能看到说system hardware failure ，硬件故障

xujinjunWY 发表于 2014-09-15 10:53

是的，初步却断可能是cpu有问题，后来重新启动了下刀片，自检成功，不报警了回复 3# sellthetime


   
页: [1]
查看完整版本: 刀片机出现橙色报警错误，日志如下，望各位大虾帮忙分析下，是什么原因导致的