rx4640安装HP-UX 11.31出错
本帖最后由 lbseraph 于 2014-05-23 17:05 编辑请教：
弄了台4640想学习，安装rhel一切正常，装ux就报这个I/O error
* Installing fileset "Networking.100BT-KRN,r=B.11.31" (15 of 2173).
* Installing fileset "Networking.INTL100-KRN,r=B.11.31" (16 of 2173).
* Installing fileset "Networking.NMS2-KRN,r=B.11.31" (17 of 2173).
* Installing fileset "Networking.PPP2-KRN,r=B.11.31" (18 of 2173).
* Installing fileset "Networking.NW-ENG-A-MAN,r=B.11.31" (19 of 2173).
* Installing fileset "Networking.LAN-PRG,r=B.11.31" (20 of 2173).
* Installing fileset "Networking.NET-RUN-64,r=B.11.31" (21 of 2173).
* Installing fileset "Networking.NET-PRG,r=B.11.31" (22 of 2173).
* Installing fileset "Streams.STREAMS2-RUN,r=B.11.31" (23 of 2173).
* Installing fileset "Streams.STREAMS-RUN,r=B.11.31" (24 of 2173).
* Installing fileset "Streams.STREAMS2-KRN,r=B.11.31" (25 of 2173).
Synchronous Page I/O error occurred while paging to/from disk
device 0x1f000000, 1K block #5296662, 8192 bytes of 8192 bytes not paged, page addr =dead31.e00000013988a000,bflag =40000f, bp = e000000155385380
ERROR: File "/tmp/ign_configure/SD_CDROM/Streams/STREAMS2-KRN.2/usr/conf/mod/clone":I/O error (5).Cannot copy it to file "/usr/conf/mod/clone".
Synchronous Page I/O error occurred while paging to/from disk
device 0x1f000000, 1K block #5296672, 8192 bytes of 8192 bytes not paged, page addr =dead31.e00000013988a000,bflag =40000f, bp = e000000155385380
Synchronous Page I/O error occurred while paging to/from disk
device 0x1f000000, 1K block #5296680, 8192 bytes of 8192 bytes not paged, page addr =dead31.e000000139884000,bflag =40000f, bp = e000000155385c80
ERROR: File "/tmp/ign_configure/SD_CDROM/Streams/STREAMS2-KRN.2/usr/conf/mod/echo":I/O error (5).Cannot copy it to file "/usr/conf/mod/echo".
ERROR: File "/tmp/ign_configure/SD_CDROM/Streams/STREAMS2-KRN.2/usr/conf/mod/ffs":I/O error (5).Cannot copy it to file "/usr/conf/mod/ffs".
ERROR: Failed installing fileset "Streams.STREAMS2-KRN,r=B.11.31".Check the above output for details.
* Installing fileset "Streams.STREAMS2-KRN,r=B.11.31" (25 of 2173).
ERROR: The internal uncompression routine (funzip) detected data corruption in file "/tmp/ign_configure/SD_CDROM/Streams/STREAMS2-KRN.2/usr/conf/mod/clone" while
uncompressing it into file "/usr/conf/mod/clone".
ERROR: File "/tmp/ign_configure/SD_CDROM/Streams/STREAMS2-KRN.2/usr/conf/mod/echo":Error 0 (0).Cannot copy it to file "/usr/conf/mod/echo".
ERROR: Failed installing fileset "Streams.STREAMS2-KRN,r=B.11.31".Check the above output for details.
* Installing fileset "Streams.STREAMS2-KRN,r=B.11.31" (25 of 2173).
ERROR: The internal uncompression routine (funzip) detected data corruption in file "/tmp/ign_configure/SD_CDROM/Streams/STREAMS2-KRN.2/usr/conf/mod/clone" while
uncompressing it into file "/usr/conf/mod/clone".
ERROR: File "/tmp/ign_configure/SD_CDROM/Streams/STREAMS2-KRN.2/usr/conf/mod/echo":Error 0 (0).Cannot copy it to file "/usr/conf/mod/echo".
ERROR: Failed installing fileset "Streams.STREAMS2-KRN,r=B.11.31".Check the above output for details.
* Installing fileset "Streams.STREAMS2-KRN,r=B.11.31" (25 of 2173).
ERROR: The internal uncompression routine (funzip) detected data corruption in file "/tmp/ign_configure/SD_CDROM/Streams/STREAMS2-KRN.2/usr/conf/mod/clone" while
uncompressing it into file "/usr/conf/mod/clone".
ERROR: File "/tmp/ign_configure/SD_CDROM/Streams/STREAMS2-KRN.2/usr/conf/mod/echo":Error 0 (0).Cannot copy it to file "/usr/conf/mod/echo".
ERROR: Failed installing fileset "Streams.STREAMS2-KRN,r=B.11.31".Check the above output for details.
ERROR: The Install Phase has suspended.
ERROR: Aborting the Install Phase.
NOTE: More information may be found in the Software Manager logfile using the command "swm job log -v 000001".
=======01/01/98 01:38:19 UTCEND Software Install failed with 15 errors. (user=root)(jobid=000001)
ERROR: Software load had one or more errors.
=======01/01/98 01:38:19 UTCThe operating system software has not been successfully loaded. The swm install(1M) application was not completed or failed to load
some key files. (exit status was = 1).
1: Change the install server and/or depot information.
2: Retry software load process (non-interactive mode).
3: Retry software load process (interactive mode).
4: Run a shell.
Shell> info -b all
SYSTEM INFORMATION
Date/Time:Jan1, 199802:04:52(19:98:01:01:02:04:52)
Manufacturer:hp
Product Name:server rx4640
Product Number:AB372A
Serial Number:USE*******
UUID:08E7F463-****
System Bus Frequency:200 MHz
PROCESSOR MODULE INFORMATION
# of L3 L4 Family/
CPU Logical Cache Cache Model Processor
ModuleCPUs Speed Size Size (hex.) RevState
-------------------------------------------------------
0 1 1.5 GHz 6 MB None 1F/01 B1 Active
1 1 1.5 GHz 6 MB None 1F/01 B1 Active
MEMORY INFORMATION
---- DIMM A --------- DIMM B --------- DIMM C --------- DIMM D -----
Press ENTER to continue, 'q' to exit:
DIMM Current DIMM Current DIMM Current DIMM Current
--------- ---------------- ---------------- ---------------- ----------
0 2048MB Active2048MB Active2048MB Active2048MB Active
1 ---- ---- ---- ----
2 ---- ---- ---- ----
3 ---- ---- ---- ----
4 ---- ---- ---- ----
5 ---- ---- ---- ----
6 ---- ---- ---- ----
7 ---- ---- ---- ----
Active Memory : 8192 MB
Installed Memory : 8192 MB
I/O INFORMATION
BOOTABLE DEVICES
OrderMedia TypePath
------------------------------------------------------
1 CDROM Acpi(HWP0002,0)/Pci(3|0)/Ata(Primary,Master)/CDROM(Entry0)
Press ENTER to continue, 'q' to exit:
2 HARDDRIVE Acpi(HWP0002,100)/Pci(1|0)/Pci(4|0)/Scsi(Pun0,Lun0)/HD(Part1,SigC5DFA466-8245-11D1-8000-D6217B60E588)
3 HARDDRIVE Acpi(HWP0002,100)/Pci(1|0)/Pci(4|0)/Scsi(Pun0,Lun0)/HD(Part3,SigC5DFA4B6-8245-11D1-8000-D6217B60E588)
SegBusDevFncVendorDevice Slot
# # # # ID ID # Path
--------------------------------------
00 00 01 000x103C0x1290 XXAcpi(HWP0002,0)/Pci(1|0)
00 00 01 010x103C0x1048 XXAcpi(HWP0002,0)/Pci(1|1)
00 00 02 000x10330x0035 XXAcpi(HWP0002,0)/Pci(2|0)
00 00 02 010x10330x0035 XXAcpi(HWP0002,0)/Pci(2|1)
00 00 02 020x10330x00E0 XXAcpi(HWP0002,0)/Pci(2|2)
00 00 03 000x10950x0649 XXAcpi(HWP0002,0)/Pci(3|0)
00 00 04 000x10020x5159 XXAcpi(HWP0002,0)/Pci(4|0)
00 20 01 000x10140x01A7 01Acpi(HWP0002,100)/Pci(1|0)
00 21 04 000x0E110x0046 01Acpi(HWP0002,100)/Pci(1|0)/Pci(4|0)
00 20 02 000x80860x1079 02Acpi(HWP0002,100)/Pci(2|0)
00 20 02 010x80860x1079 02Acpi(HWP0002,100)/Pci(2|1)
Press ENTER to continue, 'q' to exit:
Fast initialization: Enabled
System Wake-On-LAN:Enabled
BOOT INFORMATION
Monarch CPU:
CurrentPreferred
Monarch Monarch
CPU CPU
Module/ Module/
Logical Logical Warnings
------------------------
0/0 0/0
AutoBoot: ON - Timeout is : 10 sec
Boottest:
BOOTTEST Settings Default Variable
OS is not speedy boot aware.
Press ENTER to continue, 'q' to exit:
Selftest Setting
--------- --------------
early_cpu Run this test
late_cpu Run this test
platform Run this test
chipset Run this test
io_hw Run this test
mem_init Run this test
mem_test Run this test
LAN Address Information:
LAN Address Path
---------------------------------------------------------
*Mac(0012799E3022)Acpi(HWP0002,100)/Pci(2|0)/Mac(0012799E3022)
Mac(0012799E3023)Acpi(HWP0002,100)/Pci(2|1)/Mac(0012799E3023)
FIRMWARE INFORMATION
System Firmware Revision: 4.29
PAL_A: 7.31/5.37
PAL_B: 5.72
Press ENTER to continue, 'q' to exit:
EFI Spec: 1.10
EFI Intel Drop: 14.62
EFI Build: 5.48
SAL Spec: 3.01
SAL_A: 2.00
SAL_B: 4.29
POSSE: 0.20
ACPI: 7.00
SMBIOS: 2.3.2a
BMC Revision: 4.06
IPMI: 1.00
Management Processor Revision: E.03.32
Updatable EFI Drivers:
Floating-Point Software Assistance Handler:00000118
Broadcom Gigabit Ethernet Driver: 0007000A
SCSI Bus Driver: 00000021
SCSI Tape Driver: 00000020
Usb Ohci Driver: 00000033
USB Bus Driver: 00000014
USB Bot Mass Storage Driver: 00000014
Generic USB Mass Storage Driver: 00000015
WARNING AND STOP BOOT INFORMATION
Press ENTER to continue, 'q' to exit:
CHIP REVISION INFORMATION
Chip Logical Device Chip
Type ID ID Revision
------------------- ------- ------ --------
Memory Controller 0 122b 0023
Root Bridge 0 1229 0023
Host Bridge 0000 122e 0032
Host Bridge 0001 122e 0032
Host Bridge 0002 122e 0032
Host Bridge 0004 122e 0032
HotPlug Controller 0 0 0110
Host Bridge 0005 122e 0032
HotPlug Controller 0 0 0110
Host Bridge 0006 122e 0032
Other Bridge 0 0 0002
Other Bridge 0 0 0008
Baseboard MC 0 0 0406
回复 1# 杨杨得益
是通过光盘安装的还是Ignite-UX？从报错看是无法从路径/tmp/ign_configure/SD_CDROM下面正常读取文件，如果是光盘安装的话检查光盘文件是否能正常读取。
回复 3# lbseraph
光盘安装，光盘在PC可以正常读取，我换套试试 这种情况无非就检查光驱或光盘了，交叉测试下吧～ 估计是介质有问题，换一个试试看
页:
[1]