关于SUN E4900的开机步骤
各位大哥，有台闲置了一段时间的SUN Fire E4900，现在想重新用来做测试机，但是原来的维护人员不在了，现在不知道怎么开机。
我通过串口线接到sc0卡上后，得到的输出见下面（telnet ip地址也是一样的情况），只有Type0for Platform Shell，没有看到有Domain的选择，请问应该怎么进入并启动Domain啊？
Hardware Reset...
@(#) SYSTEM CONTROLLER(SC) POST 43 2005/02/22 15:29
PSR = 0x044010e5
PCR = 0x04004000
Memory size = 128MB
SelfTest running at DiagLevel:0x20
SC Boot PROM Test
BootPROM CheckSum Test
IU Test
IU instruction set Test
Little endian access Test
FPU Test
FPU instruction set Test
SparcReferenceMMU Test
SRMMU TLB RAM Test
SRMMU TLB Read miss Test
SRMMU page probe Test
SRMMU segment probe Test
SRMMU regionprobe Test
SRMMU context probe Test
IIep Internal Cache Test
DCACHE RAM access Test
DCACHE TAG access Test
DCACHE Read miss Test
DCACHE Read hit Test
DCACHE Write miss Test
DCACHE Write hit Test
ICACHE RAM access Test
ICACHE TAG access Test
ICACHE miss Test
ICACHE hit Test
ICACHE TAG flush Test
PCIC Test
PCIC Probe Test
PCIC Config Register Access Test
PCIMaster Abort Test
PCIC Init Test
Memory Test
Memory Address Test
MemBankAddrTest: start address = 0x00010000
MemBankAddrTest: start address = 0x04000000
MemBankAddrTest: start address = 0x08000000
MemBankAddrTest: start address = 0x0c000000
RIO Ebus Test
Rio Ebus Probe Test
RIO EthernetTest
Rio Enet Probe Test
Rio Ethernet Int Loopbacks Test
DUART(16552) InterSC Test
Loopback Test
COM3 port
COM4 port
Interrupt Test
COM3 port Intr #2
COM4 port Intr #2
System Clock Test
System Clock verify Test
Board0 Clock is selected
75MHZ Fixed Crystal is the selected Clock Source
CLK(Self) :0x0000ffff CLK(Other) : 0x0000ffff
REF : 0x0000221d
CLOCK(SELF) FREQ : 74.99 MHZ
CLOCK(OTHER)FREQ : 75.4 MHZ
SBBC PCI Controller Test
SBBC PCI Config Space probe Test
SBBC Internal Reg Access Test
SBBC Interrupts Test
Port1 interrupt generation TestsINTR #14
Port0 interrupt generation TestsINTR #14
SBBC Device0 Test
PS Fail Reg(SBBC Dev0) Test
SBBC Device1 Test
SRAM (SBBC Dev1) Test
Memory Address Test (Non-destructive)
SBBC Device2 Test
BId&MFG Reg (SBBC Dev2) Test
SBBC Device3 Test
FRU Prsnt Reg (SBBC Dev3) Test
SBBC Device5 Test
EPLD (SBBC Dev5) Test
TOD(M48T59) Test
TOD Init Test
TOD Functional Test
TOD NVRAM(Non-Destructive) Test
TOD Interrupts Test
I2C Register Access Test
Enable Mux Register Test
Channel MuxRegister Test
Add CommandRegister Test
Data Register Test
Local I2C AT24C64 Test
EEPROM Device Test
performing eeprom sequential read
Local I2C PCF8591 Test
VOLT_AD Device Test
channel Voltage(0x0000009B) :1.51
channel Voltage(0x0000009A) :3.30
channel Voltage(0x00000099) :4.98
channel Voltage(0x00000000) :0.0
Local I2C LM75 Test
TEMP0(IIep)Device Test
Temperature : 39.0 Degree(C)
Local I2C LM75 Test
TEMP1(Rio) Device Test
Temperature : 38.50 Degree(C)
Local I2C LM75 Test
TEMP2(CBH) Device Test
Temperature : 44.0 Degree(C)
Local I2C PCF8574 Test
Sc CSR Device Test
Console Bus Hub Test
CBH Register Access Test
POST Complete.
ERI Device Present
Getting MAC address for SSC1
MAC address is 0:3:ba:7:cc:e3
Hostname: SF4900A-SC1
Address: 192.168.0.11
Netmask: 255.255.255.0
Attached TCP/IP interface to eri unit 0
Attaching interface lo0...done
Gateway:
interrupt: 100 Mbps full duplex link up
Copyright 2005 Sun Microsystems, Inc.All rights reserved.
Use is subject to license terms.
Sun Fire System Firmware
RTOS version: 43
ScApp version: 5.19.2 Build_01
SC POST diag level: min
The date is Tuesday, May 27, 2014, 2:13:25 PM GMT.
May 27 14:13:27 SF4900A-SC1 Platform.SC: Boot: ScApp 5.19.2, RTOS 43
May 27 14:13:29 SF4900A-SC1 Platform.SC: SBBC Reset Reason(s): Power On Reset
May 27 14:13:29 SF4900A-SC1 Platform.SC: Initializing the SC SRAM
May 27 14:13:33 SF4900A-SC1 Platform.SC: Clock Source: 75MHz
May 27 14:13:46 SF4900A-SC1 Platform.SC: Spare System Controller
May 27 14:13:47 SF4900A-SC1 Platform.SC: Starting telnet server ...
System Controller 'SF4900A-SC1':
Type0for Platform Shell
Input: May 27 14:13:47 SF4900A-SC1 Platform.SC: SC Failover: enabled but not active.
System Controller 'SF4900A-SC1':
Type0for Platform Shell
Input: 0
Platform Shell - Spare System Controller
SF4900A-SC1:sc>
SF4900A-SC1:sc> help
Platform Shell commands:
connections -- show connections to this system controller
disconnect -- disconnect this connection or a specified connection
flashupdate -- update firmware
help -- show help for a command or list of commands
history -- show command history
password -- set system controller password
reboot -- reboot the system controller
restartssh -- restart SSH server (SSH must be enabled)
setdate -- set the date and time for this system controller
setfailover -- set automatic/manual SC failover
setupplatform -- configure system controller
showdate -- show the current date and time for this system controller
showenvironment -- show system controller environmental information
showfailover -- show SC Failover information
showfru -- show FRUID information
showlogs -- show the logs
showplatform -- show system controller configuration and information
showsc -- show system controller version and uptime
ssh-keygen -- generate SSH host keys or show SSH host key fingerprint
SC> console -d a
Connected to Domain A
Domain Shell for Domain A
SC0:A> setkeyswitch on SF4900A-SC1:sc> showb
输出贴出来看看 本帖最后由 freebug 于 2014-05-27 17:10 编辑
回复 2# kwtip
试过了，console命令报错：Command not found
我看过help里面也没有console命令啊：
Platform Shell commands:
connections -- show connections to this system controller
disconnect -- disconnect this connection or a specified connection
flashupdate -- update firmware
help -- show help for a command or list of commands
history -- show command history
password -- set system controller password
reboot -- reboot the system controller
restartssh -- restart SSH server (SSH must be enabled)
setdate -- set the date and time for this system controller
setfailover -- set automatic/manual SC failover
setupplatform -- configure system controller
showdate -- show the current date and time for this system controller
showenvironment -- show system controller environmental information
showfailover -- show SC Failover information
showfru -- show FRUID information
showlogs -- show the logs
showplatform -- show system controller configuration and information
showsc -- show system controller version and uptime
ssh-keygen -- generate SSH host keys or show SSH host key fingerprint
换一个sc的串口接，可能接到的sc1是slave 你连的这个slave sc，主sc显示0~4共5个选项。你可以接到另一个SC，或者用setfailover把主sc切过来。
然后再把domain 加电 回复 6# calcm
您这建议比较靠谱，lz@freebug请参考。
多谢~~~回头试试再来汇报给大家结果 多谢~~~回头试试再来汇报给大家结果 后来换到sc0启动就好了，多谢大家！
自己总结了一下，菜鸟新手不要笑，
E4900的启动过程大概分成三个过程：
a.硬件加电过程，通过启动钥匙开启，大概需要5~10分钟，可以通过并口接主sc出观察输出
b.Domain虚拟加电及自检过程，通过sc登陆到domain A（单分区结构）上用setkeyswitch on命令开启，大概需要15~30分钟
c.操作系统启动及自检过程，通过在{8} ok提示下，输入boot或boot -x（非cluster模式）来启动，大概需要5分钟
页:
[1]
2