网络摄像头不能连接电脑
以下是摄像机启动信息:请大神分析下,这个摄像头的问题出在哪里!!U-Boot 2010.06 (Aug 25 2015 - 18:11:46)
DRAM:128 MiB
Check spi flash controller v350... Found
Spi(cs1) ID: 0xC2 0x20 0x17 0xC2 0x20 0x17
Spi(cs1): Block:64KB Chip:8MB Name:"MX25L6406E"
MMC: MMC FLASH INIT: No card on slot!
In: serial
Out: serial
Err: serial
No mmc storage device found!
Hit any key to stop autoboot:1 0
saveaddr: 83fff000
Hisilicon ETH net controler
MAC: 00-00-23-34-45-66
retry: 3
retry: 2
retry: 1
Up/Down PHY not link.
8192 KiB hi_sfc at 0:0 is now current device
## Booting kernel from Legacy Image at 82000000 ...
Image Name:
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1511532 Bytes = 1.4 MiB
Load Address: 82000000
Entry Point:82000040
XIP Kernel Image ... OK
OK
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
Linux version 3.0.8 (root@linux-ay3x.site) (gcc version 4.4.1 (Hisilicon_v100(gcc4.4-290+uclibc_0.9.32.1+eabi+linuxpthread)) ) #18 Mon Sep 21 10:00:30 CST 2015
CPU: ARM926EJ-S revision 5 (ARMv5TEJ), cr=00053177
CPU: VIVT data cache, VIVT instruction cache
Machine: hi3518
Memory policy: ECC disabled, Data cache writeback
AXI bus clock 200000000.
Built 1 zonelists in Zone order, mobility grouping on.Total pages: 9906
Kernel command line: mem=39M console=ttyAMA0,115200 root=/dev/mtdblock2 mtdparts=hi_sfc:256K(boot),4672K(appfs),1024K(rootfs),1728K(ker),512K(config),8M@0(flash)
PID hash table entries: 256 (order: -2, 1024 bytes)
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 39MB = 39MB total
Memory: 35472k/35472k available, 4464k reserved, 0K highmem
Virtual kernel memory layout:
vector: 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap: 0xfff00000 - 0xfffe0000 ( 896 kB)
DMA : 0xffc00000 - 0xffe00000 ( 2 MB)
vmalloc : 0xc2800000 - 0xfe000000 ( 952 MB)
lowmem: 0xc0000000 - 0xc2700000 (39 MB)
modules : 0xbf000000 - 0xc0000000 (16 MB)
.init : 0xc0008000 - 0xc0024000 ( 112 kB)
.text : 0xc0024000 - 0xc03c7000 (3724 kB)
.data : 0xc03c8000 - 0xc03e3f00 ( 112 kB)
.bss : 0xc03e3f24 - 0xc03f5e20 (72 kB)
SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
NR_IRQS:32 nr_irqs:32 32
sched_clock: 32 bits at 100MHz, resolution 10ns, wraps every 42949ms
Console: colour dummy device 80x30
Calibrating delay loop... 218.72 BogoMIPS (lpj=1093632)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
Serial: AMBA PL011 UART driver
uart:0: ttyAMA0 at MMIO 0x20080000 (irq = 5) is a PL011 rev2
console enabled
uart:1: ttyAMA1 at MMIO 0x20090000 (irq = 5) is a PL011 rev2
bio: create slab <bio-0> at 0
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
cfg80211: Calling CRDA to update world regulatory domain
Switching to clocksource timer1
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
squashfs: version 4.0 (2009/01/31) Phillip Lougher
JFFS2 version 2.2. (NAND) 漏 2001-2006 Red Hat, Inc.
msgmni has been set to 69
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
io scheduler noop registered
io scheduler deadline registered (default)
io scheduler cfq registered
brd: module loaded
Spi id table Version 1.22
Spi(cs1) ID: 0xC2 0x20 0x17 0xC2 0x20 0x17
SPI FLASH start_up_mode is 3 Bytes
Spi(cs1):
Block:64KB
Chip:8MB
Name:"MX25L6406E"
spi size: 8MB
chip num: 1
6 cmdlinepart partitions found on MTD device hi_sfc
Creating 6 MTD partitions on "hi_sfc":
0x000000000000-0x000000040000 : "boot"
0x000000040000-0x0000004d0000 : "appfs"
0x0000004d0000-0x0000005d0000 : "rootfs"
0x0000005d0000-0x000000780000 : "ker"
0x000000780000-0x000000800000 : "config"
0x000000000000-0x000000800000 : "flash"
Fixed MDIO Bus: probed
himii: probed
phy_id = 0x2430c54
phy_id = 0xffffffff
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
hiusb-ehci hiusb-ehci.0: HIUSB EHCI
hiusb-ehci hiusb-ehci.0: new USB bus registered, assigned bus number 1
hiusb-ehci hiusb-ehci.0: irq 15, io mem 0x100b0000
hiusb-ehci hiusb-ehci.0: USB 0.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
hiusb-ohci hiusb-ohci.0: HIUSB OHCI
hiusb-ohci hiusb-ohci.0: new USB bus registered, assigned bus number 2
hiusb-ohci hiusb-ohci.0: irq 16, io mem 0x100a0000
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
mousedev: PS/2 mouse device common for all mice
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 10
NET: Registered protocol family 17
NET: Registered protocol family 15
lib80211: common routines for IEEE802.11 drivers
drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
?VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
Freeing init memory: 112K
: /etc/init.d/S00devs
: /etc/init.d/S01udev
udevd (433): /proc/433/oom_adj is deprecated, please use /proc/433/oom_score_adj instead.
Hisilicon Media Memory Zone Manager
hi3518_base: module license 'Proprietary' taints kernel.
Disabling lock debugging due to kernel taint
Hisilicon UMAP device driver interface: v3.00
pa:82700000, va:c2a80000
load sys.ko ...OK!
load viu.ko ...OK!
ISP Mod init!
load vpss.ko ....OK!
load venc.ko ...OK!
load group.ko ...OK!
load chnl.ko ...OK!
load h264e.ko ...OK!
load jpege.ko ...OK!
load rc.ko ...OK!
load region.ko ....OK!
load vda.ko ....OK!
hi_i2c init is ok!
init gpio-i2c-sony ok!
gyd test sensor is imx138_new1\n
Kernel: ssp initial ok!
*** Board tools : ver0.0.1_20120501***
: {source/utils/cmdshell.c:166}cmdstr:himm
0x201d0400: 0x00000091 --> 0x00000099
*** Board tools : ver0.0.1_20120501***
: {source/utils/cmdshell.c:166}cmdstr:himm
0x201d0020: 0x00000000 --> 0x00000008
acodec inited!
insert audio
==== Your input Sensor type is ar0130 ====
GPIO I2C module is load.
*** Board tools : ver0.0.1_20120501***
: {source/utils/cmdshell.c:166}cmdstr:himm
0x200f00bc: 0x00000000 --> 0x00000000
*** Board tools : ver0.0.1_20120501***
: {source/utils/cmdshell.c:166}cmdstr:himm
0x200f00c0: 0x00000000 --> 0x00000000
*** Board tools : ver0.0.1_20120501***
: {source/utils/cmdshell.c:166}cmdstr:himm
0x200f0020: 0x00000000 --> 0x00000000
*** Board tools : ver0.0.1_20120501***
: {source/utils/cmdshell.c:166}cmdstr:himm
0x200f0138: 0x00000000 --> 0x00000000
*** Board tools : ver0.0.1_20120501***
: {source/utils/cmdshell.c:166}cmdstr:himm
0x200f0024: 0x00000001 --> 0x00000000
*** Board tools : ver0.0.1_20120501***
: {source/utils/cmdshell.c:166}cmdstr:himm
0x200f002c: 0x00000001 --> 0x00000000
insmod: can't insert '/home/ipc_drv/extdrv/jvs_gpio.ko': No such file or directory
ADDRCONF(NETDEV_UP): eth0: link is not ready
cp: can't stat '/etc/ppp/*': No such file or directory
/etc/network is not a mountpoint
route: SIOCDELRT: No such process
route: SIOCDELRT: No such process
interface info here...
iface = eth0
inet = dhcp
ip = 192.168.0.254
netmask = 255.255.255.0
gateway = 192.168.0.1
dns = 8.8.8.8
killall: udhcpc: no process killed
killall: wpa_supplicant: no process killed
iface eth0 udhcpc
/home/bashrc.sh: line 53: hwclock: not found
udhcpc (v1.16.1) started
(none) login: Sending discover...
/progs/html/cgi-bin/snapshot is not a mountpoint
SQUASHFS error: xz_dec_run error, data probably corrupt
SQUASHFS error: squashfs_read_data failed to read block 0x11cf38
SQUASHFS error: Unable to read data cache entry
SQUASHFS error: Unable to read page, block 11cf38, size 199d0
SQUASHFS error: Unable to read data cache entry
SQUASHFS error: Unable to read page, block 11cf38, size 199d0
SQUASHFS error: Unable to read data cache entry
SQUASHFS error: Unable to read page, block 11cf38, size 199d0
SQUASHFS error: Unable to read data cache entry
SQUASHFS error: Unable to read page, block 11cf38, size 199d0
SQUASHFS error: Unable to read data cache entry
SQUASHFS error: Unable to read page, block 11cf38, size 199d0
cp: read error: Input/output error
Segmentation fault
umount: /dev/mtdblock1 busy - remounted read-only
umount: /dev/mtdblock1 busy - remounted read-only
umount: tmpfs busy - remounted read-only
umount: tmpfs busy - remounted read-only
The system is going down NOW!
Received SIGTERM
Sent SIGTERM to all processes
Sent SIGKILL to all processes
Requesting system reboot
Restarting system.
U-Boot 2010.06 (Aug 25 2015 - 18:11:46)
DRAM:128 MiB
Check spi flash controller v350... Found
Spi(cs1) ID: 0xC2 0x20 0x17 0xC2 0x20 0x17
Spi(cs1): Block:64KB Chip:8MB Name:"MX25L6406E"
MMC: MMC FLASH INIT: No card on slot!
In: serial
Out: serial
Err: serial
No mmc storage device found!
Hit any key to stop autoboot:1 0
saveaddr: 83fff000
Hisilicon ETH net controler
MAC: 00-00-23-34-45-66
retry: 3
retry: 2
retry: 1
Up/Down PHY not link.
8192 KiB hi_sfc at 0:0 is now current device
## Booting kernel from Legacy Image at 82000000 ...
Image Name:
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1511532 Bytes = 1.4 MiB
Load Address: 82000000
Entry Point:82000040
XIP Kernel Image ... OK
OK
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
Linux version 3.0.8 (root@linux-ay3x.site) (gcc version 4.4.1 (Hisilicon_v100(gcc4.4-290+uclibc_0.9.32.1+eabi+linuxpthread)) ) #18 Mon Sep 21 10:00:30 CST 2015
CPU: ARM926EJ-S revision 5 (ARMv5TEJ), cr=00053177
CPU: VIVT data cache, VIVT instruction cache
Machine: hi3518
Memory policy: ECC disabled, Data cache writeback
AXI bus clock 200000000.
Built 1 zonelists in Zone order, mobility grouping on.Total pages: 9906
Kernel command line: mem=39M console=ttyAMA0,115200 root=/dev/mtdblock2 mtdparts=hi_sfc:256K(boot),4672K(appfs),1024K(rootfs),1728K(ker),512K(config),8M@0(flash)
PID hash table entries: 256 (order: -2, 1024 bytes)
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 39MB = 39MB total
Memory: 35472k/35472k available, 4464k reserved, 0K highmem
Virtual kernel memory layout:
vector: 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap: 0xfff00000 - 0xfffe0000 ( 896 kB)
DMA : 0xffc00000 - 0xffe00000 ( 2 MB)
vmalloc : 0xc2800000 - 0xfe000000 ( 952 MB)
lowmem: 0xc0000000 - 0xc2700000 (39 MB)
modules : 0xbf000000 - 0xc0000000 (16 MB)
.init : 0xc0008000 - 0xc0024000 ( 112 kB)
.text : 0xc0024000 - 0xc03c7000 (3724 kB)
.data : 0xc03c8000 - 0xc03e3f00 ( 112 kB)
.bss : 0xc03e3f24 - 0xc03f5e20 (72 kB)
SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
NR_IRQS:32 nr_irqs:32 32
sched_clock: 32 bits at 100MHz, resolution 10ns, wraps every 42949ms
Console: colour dummy device 80x30
Calibrating delay loop... 218.72 BogoMIPS (lpj=1093632)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
Serial: AMBA PL011 UART driver
uart:0: ttyAMA0 at MMIO 0x20080000 (irq = 5) is a PL011 rev2
console enabled
uart:1: ttyAMA1 at MMIO 0x20090000 (irq = 5) is a PL011 rev2
bio: create slab <bio-0> at 0
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
cfg80211: Calling CRDA to update world regulatory domain
Switching to clocksource timer1
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
squashfs: version 4.0 (2009/01/31) Phillip Lougher
JFFS2 version 2.2. (NAND) 漏 2001-2006 Red Hat, Inc.
msgmni has been set to 69
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
io scheduler noop registered
io scheduler deadline registered (default)
io scheduler cfq registered
brd: module loaded
Spi id table Version 1.22
Spi(cs1) ID: 0xC2 0x20 0x17 0xC2 0x20 0x17
SPI FLASH start_up_mode is 3 Bytes
Spi(cs1):
Block:64KB
Chip:8MB
Name:"MX25L6406E"
spi size: 8MB
chip num: 1
6 cmdlinepart partitions found on MTD device hi_sfc
Creating 6 MTD partitions on "hi_sfc":
0x000000000000-0x000000040000 : "boot"
0x000000040000-0x0000004d0000 : "appfs"
0x0000004d0000-0x0000005d0000 : "rootfs"
0x0000005d0000-0x000000780000 : "ker"
0x000000780000-0x000000800000 : "config"
0x000000000000-0x000000800000 : "flash"
Fixed MDIO Bus: probed
himii: probed
phy_id = 0x2430c54
phy_id = 0xffffffff
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
hiusb-ehci hiusb-ehci.0: HIUSB EHCI
hiusb-ehci hiusb-ehci.0: new USB bus registered, assigned bus number 1
hiusb-ehci hiusb-ehci.0: irq 15, io mem 0x100b0000
hiusb-ehci hiusb-ehci.0: USB 0.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
hiusb-ohci hiusb-ohci.0: HIUSB OHCI
hiusb-ohci hiusb-ohci.0: new USB bus registered, assigned bus number 2
hiusb-ohci hiusb-ohci.0: irq 16, io mem 0x100a0000
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
mousedev: PS/2 mouse device common for all mice
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 10
NET: Registered protocol family 17
NET: Registered protocol family 15
lib80211: common routines for IEEE802.11 drivers
drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
?VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
Freeing init memory: 112K
: /etc/init.d/S00devs
: /etc/init.d/S01udev
udevd (433): /proc/433/oom_adj is deprecated, please use /proc/433/oom_score_adj instead.
Hisilicon Media Memory Zone Manager
hi3518_base: module license 'Proprietary' taints kernel.
Disabling lock debugging due to kernel taint
Hisilicon UMAP device driver interface: v3.00
pa:82700000, va:c2a80000
load sys.ko ...OK!
load viu.ko ...OK!
ISP Mod init!
load vpss.ko ....OK!
load venc.ko ...OK!
load group.ko ...OK!
load chnl.ko ...OK!
load h264e.ko ...OK!
load jpege.ko ...OK!
load rc.ko ...OK!
load region.ko ....OK!
load vda.ko ....OK!
hi_i2c init is ok!
init gpio-i2c-sony ok!
gyd test sensor is imx138_new1\n
Kernel: ssp initial ok!
*** Board tools : ver0.0.1_20120501***
: {source/utils/cmdshell.c:166}cmdstr:himm
0x201d0400: 0x00000091 --> 0x00000099
*** Board tools : ver0.0.1_20120501***
: {source/utils/cmdshell.c:166}cmdstr:himm
0x201d0020: 0x00000008 --> 0x00000008
acodec inited!
insert audio
==== Your input Sensor type is ar0130 ====
GPIO I2C module is load.
*** Board tools : ver0.0.1_20120501***
: {source/utils/cmdshell.c:166}cmdstr:himm
0x200f00bc: 0x00000000 --> 0x00000000
*** Board tools : ver0.0.1_20120501***
: {source/utils/cmdshell.c:166}cmdstr:himm
0x200f00c0: 0x00000000 --> 0x00000000
*** Board tools : ver0.0.1_20120501***
: {source/utils/cmdshell.c:166}cmdstr:himm
0x200f0020: 0x00000000 --> 0x00000000
*** Board tools : ver0.0.1_20120501***
: {source/utils/cmdshell.c:166}cmdstr:himm
0x200f0138: 0x00000000 --> 0x00000000
*** Board tools : ver0.0.1_20120501***
: {source/utils/cmdshell.c:166}cmdstr:himm
0x200f0024: 0x00000001 --> 0x00000000
*** Board tools : ver0.0.1_20120501***
: {source/utils/cmdshell.c:166}cmdstr:himm
0x200f002c: 0x00000001 --> 0x00000000
insmod: can't insert '/home/ipc_drv/extdrv/jvs_gpio.ko': No such file or directory
ADDRCONF(NETDEV_UP): eth0: link is not ready
cp: can't stat '/etc/ppp/*': No such file or directory
/etc/network is not a mountpoint
route: SIOCDELRT: No such process
route: SIOCDELRT: No such process
interface info here...
iface = eth0
inet = dhcp
ip = 192.168.0.254
netmask = 255.255.255.0
gateway = 192.168.0.1
dns = 8.8.8.8
killall: udhcpc: no process killed
killall: wpa_supplicant: no process killed
iface eth0 udhcpc
/home/bashrc.sh: line 53: hwclock: not found
udhcpc (v1.16.1) started
Sending discover...
(none) login: /progs/html/cgi-bin/snapshot is not a mountpoint
Sending discover...
/tmp/sctrl cmd= to enable debug
/tmp/sctrl log= to set syslog level
open dev failed!,not support!
【SDK.Version:"Hi3518_MPP_V1.0.A.1"】
building date: Dec 18 2015: 11:56:37
y=2015,m=3,d=27
-------------------------------------bUSEAEC:0
check id ruuning high 255,low 255
>>>>LK test sensor type is SENSOR_AR0130
Aptina AR0130 sensor 960P30fps init success!
Sending discover...
Aptina AR0130 sensor 960P30fps init success!
main start AI and AO
sampleRate=8000,bitWidth=1
pageaddr:4006e000,dgbaddr:4006e000,size:0
set mic gain 0x00021212(0x4)
system: himm 0x20050068 0x00021212
*** Board tools : ver0.0.1_20120501***
: {source/utils/cmdshell.c:166}cmdstr:himm
0x20050068: 0x00FE2C2C --> 0x00021212
check id ruuning high 255,low 255
>>>>LK test sensor type is SENSOR_AR0130
get sensor ID :3
check inet: dhcp
-------Jmp4pkg date: 2015-01-05Ver: 1.0.1.17
zrtsp start......
schedule10
schedule20
sch1TimeStart6:0
sch1TimeEnd18:0
sch2TimeStart18:0
sch2TimeEnd6:0
vencw: 1280x720
=====>>>REC_MIN_MB_SPACE_NEEDED=2048/8*600=150
osd pos x=0,y=0,fontSize=32,18
linenum=0
dooralarm not support
IP auto adapt open!
>>>>>>>>>>>>>>>>>>MY ID IS:a1d646
Start create MLAN
mptzosd_init:af not support!
vencw: 1280x720
restart here:connection: 0
=====>>>REC_MIN_MB_SPACE_NEEDED=2048/8*600=150
=====>>>REC_MIN_MB_SPACE_NEEDED=2048/8*600=150
system: killall thttpd
killall: thttpd: no process killed
system: /progs/bin/thttpd -d /progs/html/ -c "/cgi-bin/*|/onvif/*" -u root -T utf-8&
=====>>>REC_MIN_MB_SPACE_NEEDED=2048/8*600=150
dooralarm not support
Failed open /etc/conf.d/jovision/presetpos.cfg, because: No such file or directory
NO support Af!
NOt support pu&c!
dooralarm not support
Trun to DayMode...
jvserver************v2.0.78.10
### tinyonvif built: Jun 16 2015: 10:57:32
ovdistar
*******
ZNPNP_INIT
*********
### libgb28181 built: Nov 16 2015: 01:04:35
ipc sdk dll loading error.
:346 setsockopt error! errstr: No such device
===ov pid:779
ZNPNP RecvBroadcase Wait ...
ALL PORT USED:8099,554,23,8127,6666,8732,40741,3702,9100,9104,9106,6072,8899,1998,17
dooralarm not support
system: insmod /home/ipc_drv/extdrv/wdt.ko default_margin=60 nodeamon=1
Hisilicon Watchdog Timer: 0.01 initialized. default_margin=60 sec (nowayout= 0, nodeamon= 1)
gethostbyname error:111, try ngethostbyname..
gethostbyname error:111, try ngethostbyname..
gethostbyname error:111, try ngethostbyname..
gethostbyname error:111, try ngethostbyname..
gethostbyname error:111, try ngethostbyname..
gethostbyname error:111, try ngethostbyname..
gethostbyname error:111, try ngethostbyname..
gethostbyname error:111, try ngethostbyname..
gethostbyname error:111, try ngethostbyname..
页:
[1]