菜鸟100问
目录Packages 和 Ports
软件安装卸载工具41 多线程下载ports里的包42 从ports中查找软件43 硬盘空间特紧张44~45 portupgrade47~49 portsnap 简单使用50 Packages 和 Ports精华51 初学者必须知道的事52~59
Shell
命令解释程序Shell60 Shell精华61 Shell常见问题62~63 硬盘安装FreeBSD66 环境设定67 ee编辑器68 vi编辑器69
FreeBSD基础应用
基础应用精华71 基础应用集锦72~76 基础应用补充79~80 全能服务器基础应用篇81~88 基础应用小技巧89~90 基本系統指令介紹91 FreeBSD目录说明92 摘录Handbook读书笔记-第3章93~95
防火墙
防火墙基础100 PF 防火墙101 PF学习笔记102~120
FreeBSD6.1没路由器, ADSL拨号上网, ISP动态分配IP, RTL8139
检查过网线,网卡也在启动时显示出来,
就是modem死活地不通,modem指示灯不闪.
怎么回事?希望详细些!
以下是我的ppp.conf
default:
set log Phase Chat LCP IPCP CCP tun command
ident user-ppp VERSION (built COMPILATIONDATE)
set device PPPoE:r10
set speed sync
set mru 1492
set mtu 1492
set ctsrts off
set timeout 30
disable lqr
deny lqr
add default HISADDR
enable dns
adsl:
set authname *********@******
set authkey **********
set dial
set login
set ifaddr 10.0.0.1/0 10.0.0.2/0
[ 本帖最后由 minok 于 2006-12-10 11:16 编辑 ] reset一下你的modem 拨号以后是什么提示啊 把配置文件精简些可能会更好,
如 set mru 1492
set mtu 1492 default:
set log Phase Chat LCP IPCP CCP tun command
ident user-ppp VERSION (built COMPILATIONDATE)
set device PPPoE:r10
set speed sync
set mru 1492
set mtu 1492
set ctsrts off
you should use "tab " maybe
"tab" set * default:
set log Phase tun command # you can add more detailed logging if you wish
set ifaddr 10.0.0.1/0 10.0.0.2/0
name_of_service_provider:
set device PPPoE:xl1 # replace xl1 with your Ethernet device
set authname YOURLOGINNAME
set authkey YOURPASSWORD
set dial
set login
add default HISADDR
it is in handbook , you can rewrite over it .
have a good time! 原帖由 limutian 于 2006-11-8 12:11 发表
default:
set log Phase tun command # you can add more detailed logging if you wish
set ifaddr 10.0.0.1/0 10.0.0.2/0
name_of_service_provider:
set device PPPoE:xl1 # repl ...
已按照这方法做了,<tab> set *还是连不上modem,另外我发现网卡没配置好,
出现以下问题:
# ppp –ddial adsl
Working in ddial mode
Using interface: tun0
# ifconfig
r10: flags=8802<BROADCAST,SIMPLEX,MULTICAST> mtu 1500
options=8<VLAN_MTU>
ether 00:e0:4c:20:0c:57
media: Ethernet autoselect (10baseT/UTP)
status: active
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384
inet6 ::1 prefixlen 128
inet6 fe80::1%lo0 prefixlen 64 scopeid 0x2
inet 127.0.0.1 netmask 0xff000000
tun0: flags=8051<UP,POINTOPOINT,RUNNING,MULTICAST> mtu 1500
Opened by PID 191
当我选网卡为DHCP时,即/etc/rc.conf 并加入下面的设置：
ifconfig_r10="DHCP"
可以接通modem,依然无法拨号.
该如何做?请指教 set device PPPoE:r10
rl0 吧不是r10
应该有日志的看看把 多谢各位指教,终于可以上网了,特别感谢limutian 提出错误
是我大意了,呵呵,以后一定检查清楚.
# ifconfig
rl0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
options=8<VLAN_MTU>
inet6 fe80::2e0:4cff:fe20:c57%rl0 prefixlen 64 scopeid 0x1
ether 00:e0:4c:20:0c:57
media: Ethernet autoselect (100baseTX <full-duplex>)
status: active
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384
inet6 ::1 prefixlen 128
inet6 fe80::1%lo0 prefixlen 64 scopeid 0x2
inet 127.0.0.1 netmask 0xff000000
tun0: flags=8051<UP,POINTOPOINT,RUNNING,MULTICAST> mtu 1492
inet 218.72.106.94 --> 61.174.64.21 netmask 0xffffffff
Opened by PID 191 我已装好ports不知为什么无法安装软件包,例如:
# cd /usr/ports/chinese/kde3-i18n-zh_CN
# make install clean
(错误信息.........略)
***Error code 1
Stop in /usr/ports/chinese/kde3-i18n-zh_CN.
就下载不了,是DNS问题还是其它? (错误信息.........略)