Chinaunix

标题: E20k + QLA2460 (FW v1.24 ) + HDS9990 +sol10u7 + MPXIO san boot安装成功 [打印本页]

作者: IT业的民工 时间: 2009-06-01 15:35
标题: E20k + QLA2460 (FW v1.24 ) + HDS9990 +sol10u7 + MPXIO san boot安装成功
UFS rootfs:

Sun Fire E20K, using IOSRAM based Console
Copyright 2007 Sun Microsystems, Inc.  All rights reserved.
OpenBoot 4.22.32, 16384 MB memory installed, Serial #44701348.
Ethernet address 0:0:be:aa:16:a4, Host ID: 82aa16a4.

{40} ok devalias
net                   /pci@7c,70.0000/pci@1/network@3,1
man-net                /pci@7c,70.0000/pci@1/network@3,1
hds-lun0-a             /pci@7c,600000/SUNW,qlc@1/fp@0,0/disk@w50060e80044ee372,0:a
hds-lun1-a             /pci@7c,600000/SUNW,qlc@1/fp@0,0/disk@w50060e80044ee372,1:a
hds-lun2-a             /pci@7c,600000/SUNW,qlc@1/fp@0,0/disk@w50060e80044ee372,2:a
hds-lun3-a             /pci@7c,600000/SUNW,qlc@1/fp@0,0/disk@w50060e80044ee372,3:a
hds-lun0-b             /pci@7d,600000/SUNW,qlc@1/fp@0,0/disk@w50060e80044ee362,0:a
hds-lun1-b             /pci@7d,600000/SUNW,qlc@1/fp@0,0/disk@w50060e80044ee362,1:a
hds-lun2-b             /pci@7d,600000/SUNW,qlc@1/fp@0,0/disk@w50060e80044ee362,2:a
hds-lun3-b             /pci@7d,600000/SUNW,qlc@1/fp@0,0/disk@w50060e80044ee362,3:a
name                   aliases
{40} ok
Rebooting with command: boot hds-lun2-a
Boot device: /pci@7c,600000/SUNW,qlc@1/fp@0,0/disk@w50060e80044ee372,2:a  File and args:
QLogic QLA2460 Host Adapter Driver(SPARC): 1.24  11/15/06
Firmware version 4.00.26
SunOS Release 5.10 Version Generic_139555-08 64-bit
Copyright 1983-2009 Sun Microsystems, Inc.  All rights reserved.
Use is subject to license terms.
Hostname: e20k-2-e
SUNW,eri0 : 100 Mbps half duplex link up
SUNW,eri0 : No response from Ethernet network : Link down -- cable problem?/dev/rdsk/c0t50060E80044EE372d2s4 is clean
Reading ZFS config: done.
SUNW,eri0 : 100 Mbps half duplex link up

e20k-2-e console login: May 25 17:06:52 e20k-2-e sendmail[594]: My unqualified host name (e20k-2-e) unknown; sleeping for retry
May 25 17:06:52 e20k-2-e sendmail[595]: My unqualified host name (e20k-2-e) unknown; sleeping for retry
May 25 17:07:52 e20k-2-e sendmail[594]: unable to qualify my own domain name (e20k-2-e) -- using short name
May 25 17:07:52 e20k-2-e sendmail[595]: unable to qualify my own domain name (e20k-2-e) -- using short name

e20k-2-e console login: root
Password:
Last login: Wed May 20 12:40:37 on console
May 25 17:11:38 e20k-2-e login: ROOT LOGIN /dev/console
Sun Microsystems Inc. SunOS 5.10    Generic January 2005
# df -k
文件系统             千字节用了可用容量    挂接在
/dev/dsk/c0t50060E80044EE372d2s0
                  32274285 4743524 27208019 15% /
/devices                0    0    0    0% /devices
ctfs                      0    0    0    0% /system/contract
proc                      0    0    0    0% /proc
mnttab                   0    0    0    0% /etc/mnttab
swap                30039848 1600 30038248    1% /etc/svc/volatile
objfs                   0    0    0    0% /system/object
sharefs                   0    0    0    0% /etc/dfs/sharetab
/platform/sun4u-us3/lib/libc_psr/libc_psr_hwcap2.so.1
                  32274285 4743524 27208019 15% /platform/sun4u-us3/lib/libc_psr.so.1
/platform/sun4u-us3/lib/sparcv9/libc_psr/libc_psr_hwcap2.so.1
                  32274285 4743524 27208019 15% /platform/sun4u-us3/lib/sparcv9/libc_psr.so.1
fd                      0    0    0    0% /dev/fd
/dev/dsk/c0t50060E80044EE372d2s3
                  1988719 71494 1857564    4% /var
swap                30038352    104 30038248    1% /tmp
swap                30038288    40 30038248    1% /var/run
/dev/dsk/c0t50060E80044EE372d2s4
                  7060637 7025 6983006    1% /export/home
# format
Searching for disks...done

AVAILABLE DISK SELECTIONS:
   0. c0t50060E80044EE372d0 <HITACHI-OPEN-V-SUN-5008 cyl 15666 alt 2 hd 15 sec 512>
      /pci@7c,600000/SUNW,qlc@1/fp@0,0/ssd@w50060e80044ee372,0
   1. c0t50060E80044EE372d1 <HITACHI-OPEN-V-SUN-5008 cyl 15666 alt 2 hd 15 sec 512>
      /pci@7c,600000/SUNW,qlc@1/fp@0,0/ssd@w50060e80044ee372,1
   2. c0t50060E80044EE372d2 <HITACHI-OPEN-V-SUN-5008 cyl 15666 alt 2 hd 15 sec 512>
      /pci@7c,600000/SUNW,qlc@1/fp@0,0/ssd@w50060e80044ee372,2
   3. c0t50060E80044EE372d3 <HITACHI-OPEN-V-SUN-5008 cyl 15666 alt 2 hd 15 sec 512>
      /pci@7c,600000/SUNW,qlc@1/fp@0,0/ssd@w50060e80044ee372,3
   4. c1t50060E80044EE362d0 <HITACHI-OPEN-V-SUN-5008 cyl 15666 alt 2 hd 15 sec 512>
      /pci@7d,600000/SUNW,qlc@1/fp@0,0/ssd@w50060e80044ee362,0
   5. c1t50060E80044EE362d1 <HITACHI-OPEN-V-SUN-5008 cyl 15666 alt 2 hd 15 sec 512>
      /pci@7d,600000/SUNW,qlc@1/fp@0,0/ssd@w50060e80044ee362,1
   6. c1t50060E80044EE362d2 <HITACHI-OPEN-V-SUN-5008 cyl 15666 alt 2 hd 15 sec 512>
      /pci@7d,600000/SUNW,qlc@1/fp@0,0/ssd@w50060e80044ee362,2
   7. c1t50060E80044EE362d3 <HITACHI-OPEN-V-SUN-5008 cyl 15666 alt 2 hd 15 sec 512>
      /pci@7d,600000/SUNW,qlc@1/fp@0,0/ssd@w50060e80044ee362,3
Specify disk (enter its number): ^D
# cat /etc/vfstab
#device       device       mount          FS    fsck mount mount
#to mount    to fsck       point          type pass at boot options
#
fd    -    /dev/fd fd    -    no    -
/proc -    /proc proc -    no    -
/dev/dsk/c0t50060E80044EE372d2s1       -    -    swap -    no    -
/dev/dsk/c0t50060E80044EE372d2s0       /dev/rdsk/c0t50060E80044EE372d2s0    /    ufs    1    no    -
/dev/dsk/c0t50060E80044EE372d2s3       /dev/rdsk/c0t50060E80044EE372d2s3    /var ufs    1    no    -
/dev/dsk/c0t50060E80044EE372d2s4       /dev/rdsk/c0t50060E80044EE372d2s4    /export/home ufs    2    yes    -
/devices       -    /devices       devfs -    no    -
sharefs -    /etc/dfs/sharetab    sharefs -    no    -
ctfs -    /system/contract       ctfs -    no    -
objfs -    /system/object  objfs -    no    -
swap -    /tmp tmpfs -    yes    -
# stmsboot  -e

警告：可以对每个受支持的具有多路径功能的控制器执行 stmsboot
      已在主机中检测到。在系统中，这些控制器为

/pci@7c,600000/SUNW,qlc@1/fp@0,0
/pci@7d,600000/SUNW,qlc@1/fp@0,0
/pci@7d,600000/SUNW,qlc@1,1/fp@0,0

如果您不希望对这些控制器执行操作，请退出 stmsboot
并使用 -D { fp | mpt } 重新调用以指定要针对哪些控制器
来修改多路径配置。

是否继续？[y/n]（缺省值：Y） y
警告：此操作将需要重新引导。
是否要继续？[y/n]（缺省值：y）y
这些更改将在重新引导系统后生效。
现在就重新引导系统吗？ [y/n]（缺省值：y） y
May 25 17:13:50 e20k-2-e reboot: rebooted by root
updating /platform/sun4u/boot_archive
May 25 17:13:56 e20k-2-e syslogd: going down on signal 15
May 25 17:13:56 /usr/lib/snmp/snmpdx: received signal 15
syncing file systems... done
rebooting...

Resetting...

Sun Fire E20K, using IOSRAM based Console
Copyright 2007 Sun Microsystems, Inc.  All rights reserved.
OpenBoot 4.22.32, 16384 MB memory installed, Serial #44701348.
Ethernet address 0:0:be:aa:16:a4, Host ID: 82aa16a4.

Rebooting with command: boot hds-lun2-a
Boot device: /pci@7c,600000/SUNW,qlc@1/fp@0,0/disk@w50060e80044ee372,2:a  File and args:
QLogic QLA2460 Host Adapter Driver(SPARC): 1.24  11/15/06
Firmware version 4.00.26
SunOS Release 5.10 Version Generic_139555-08 64-bit
Copyright 1983-2009 Sun Microsystems, Inc.  All rights reserved.
Use is subject to license terms.
Hostname: e20k-2-e
SUNW,eri0 : 100 Mbps half duplex link up
stmsboot: configuring devices

stmsboot: vfstab has been updated
The / file system (/dev/rdsk/c3t60060E80044EE30000004EE3000000BFd0s0) is being checked.
/dev/rdsk/c3t60060E80044EE30000004EE3000000BFd0s4 is clean
Reading ZFS config: done.

e20k-2-e console login: rootMay 25 17:27:06 e20k-2-e sendmail[624]: My unqualified host name (e20k-2-e) unknown; sleeping for retry
May 25 17:27:06 e20k-2-e sendmail[625]: My unqualified host name (e20k-2-e) unknown; sleeping for retry

Password:
Last login: Mon May 25 17:11:38 on console
May 25 17:27:07 e20k-2-e login: ROOT LOGIN /dev/console
Sun Microsystems Inc. SunOS 5.10    Generic January 2005
# df -h
文件系统             大小用了可用容量    挂接在
/dev/dsk/c3t60060E80044EE30000004EE3000000BFd0s0
                     31G 4.4G 26G 15% /
/devices                0K    0K    0K    0% /devices
ctfs                   0K    0K    0K    0% /system/contract
proc                   0K    0K    0K    0% /proc
mnttab                0K    0K    0K    0% /etc/mnttab
swap                   29G 1.6M 29G    1% /etc/svc/volatile
objfs                   0K    0K    0K    0% /system/object
sharefs                0K    0K    0K    0% /etc/dfs/sharetab
/platform/sun4u-us3/lib/libc_psr/libc_psr_hwcap2.so.1
                     31G 4.4G 26G 15% /platform/sun4u-us3/lib/libc_psr.so.1
/platform/sun4u-us3/lib/sparcv9/libc_psr/libc_psr_hwcap2.so.1
                     31G 4.4G 26G 15% /platform/sun4u-us3/lib/sparcv9/libc_psr.so.1
fd                      0K    0K    0K    0% /dev/fd
/dev/dsk/c3t60060E80044EE30000004EE3000000BFd0s3
                     1.9G 70M 1.8G    4% /var
swap                   29G 32K 29G    1% /tmp
swap                   29G 32K 29G    1% /var/run
/dev/dsk/c3t60060E80044EE30000004EE3000000BFd0s4
                     6.7G 6.9M 6.7G    1% /export/home
# cat /etc/vfstab
#device       device       mount          FS    fsck mount mount
#to mount    to fsck       point          type pass at boot options
#
fd    -    /dev/fd fd    -    no    -
/proc -    /proc proc -    no    -
/dev/dsk/c3t60060E80044EE30000004EE3000000BFd0s1       -    -    swap -    no    -
/dev/dsk/c3t60060E80044EE30000004EE3000000BFd0s0       /dev/rdsk/c3t60060E80044EE30000004EE3000000BFd0s0    /    ufs    1    no    -
/dev/dsk/c3t60060E80044EE30000004EE3000000BFd0s3       /dev/rdsk/c3t60060E80044EE30000004EE3000000BFd0s3    /var ufs    1    no    -
/dev/dsk/c3t60060E80044EE30000004EE3000000BFd0s4       /dev/rdsk/c3t60060E80044EE30000004EE3000000BFd0s4    /export/home ufs    2    yes    -
/devices       -    /devices       devfs -    no    -
sharefs -    /etc/dfs/sharetab    sharefs -    no    -
ctfs -    /system/contract       ctfs -    no    -
objfs -    /system/object  objfs -    no    -
swap -    /tmp tmpfs -    yes    -
#

# format
Searching for disks...done

AVAILABLE DISK SELECTIONS:
   0. c3t60060E80044EE30000004EE3000000B2d0 <HITACHI-OPEN-V-SUN-5008 cyl 15666 alt 2 hd 15 sec 512>
      /scsi_vhci/ssd@g60060e80044ee30000004ee3000000b2
   1. c3t60060E80044EE30000004EE3000000B9d0 <HITACHI-OPEN-V-SUN-5008 cyl 15666 alt 2 hd 15 sec 512>
      /scsi_vhci/ssd@g60060e80044ee30000004ee3000000b9
   2. c3t60060E80044EE30000004EE3000000BFd0 <HITACHI-OPEN-V-SUN-5008 cyl 15666 alt 2 hd 15 sec 512>
      /scsi_vhci/ssd@g60060e80044ee30000004ee3000000bf
   3. c3t60060E80044EE30000004EE3000000C7d0 <HITACHI-OPEN-V-SUN-5008 cyl 15666 alt 2 hd 15 sec 512>
      /scsi_vhci/ssd@g60060e80044ee30000004ee3000000c7
Specify disk (enter its number): ^D
# luxadm display /dev/rdsk/c3t60060E80044EE30000004EE3000000B2d0s2
DEVICE PROPERTIES for disk: /dev/rdsk/c3t60060E80044EE30000004EE3000000B2d0s2
  Vendor:             HITACHI
  Product ID:          OPEN-V    -SUN
  Revision:          5008
  Serial Num:          50 04EE300B2
  Unformatted capacity: 58757.812 MBytes
  Write Cache:       Enabled
  Read Cache:          Enabled
Minimum prefetch: 0x0
Maximum prefetch: 0x0
  Device Type:       Disk device
  Path(s):

  /dev/rdsk/c3t60060E80044EE30000004EE3000000B2d0s2
  /devices/scsi_vhci/ssd@g60060e80044ee30000004ee3000000b2:c,raw
Controller          /devices/pci@7c,600000/SUNW,qlc@1/fp@0,0
Device Address             50060e80044ee372,0
Host controller port WWN 2100001b320b8ec5
Class                      primary
State                      ONLINE
Controller          /devices/pci@7d,600000/SUNW,qlc@1/fp@0,0
Device Address             50060e80044ee362,0
Host controller port WWN 2100001b320bc537
Class                      primary
State                      ONLINE

ZFS rootfs :

# format
Searching for disks...done

AVAILABLE DISK SELECTIONS:
   0. c0t50060E80044EE372d0 <HITACHI-OPEN-V-SUN-5008 cyl 15666 alt 2 hd 15 sec 512>
      /pci@7c,600000/SUNW,qlc@1/fp@0,0/ssd@w50060e80044ee372,0
   1. c0t50060E80044EE372d1 <HITACHI-OPEN-V-SUN-5008 cyl 15666 alt 2 hd 15 sec 512>
      /pci@7c,600000/SUNW,qlc@1/fp@0,0/ssd@w50060e80044ee372,1
   2. c0t50060E80044EE372d2 <HITACHI-OPEN-V-SUN-5008 cyl 15666 alt 2 hd 15 sec 512>
      /pci@7c,600000/SUNW,qlc@1/fp@0,0/ssd@w50060e80044ee372,2
   3. c0t50060E80044EE372d3 <HITACHI-OPEN-V-SUN-5008 cyl 15666 alt 2 hd 15 sec 512>
      /pci@7c,600000/SUNW,qlc@1/fp@0,0/ssd@w50060e80044ee372,3
   4. c1t50060E80044EE362d0 <HITACHI-OPEN-V-SUN-5008 cyl 15666 alt 2 hd 15 sec 512>
      /pci@7d,600000/SUNW,qlc@1/fp@0,0/ssd@w50060e80044ee362,0
   5. c1t50060E80044EE362d1 <HITACHI-OPEN-V-SUN-5008 cyl 15666 alt 2 hd 15 sec 512>
      /pci@7d,600000/SUNW,qlc@1/fp@0,0/ssd@w50060e80044ee362,1
   6. c1t50060E80044EE362d2 <HITACHI-OPEN-V-SUN-5008 cyl 15666 alt 2 hd 15 sec 512>
      /pci@7d,600000/SUNW,qlc@1/fp@0,0/ssd@w50060e80044ee362,2
   7. c1t50060E80044EE362d3 <HITACHI-OPEN-V-SUN-5008 cyl 15666 alt 2 hd 15 sec 512>
      /pci@7d,600000/SUNW,qlc@1/fp@0,0/ssd@w50060e80044ee362,3
Specify disk (enter its number): ^D
# df -k
文件系统             千字节用了可用容量    挂接在
rpool/ROOT/s10s_u7wos_08
                  58834944 4924932 20275471 20% /
/devices                0    0    0    0% /devices
ctfs                      0    0    0    0% /system/contract
proc                      0    0    0    0% /proc
mnttab                   0    0    0    0% /etc/mnttab
swap                29944496    696 29943800    1% /etc/svc/volatile
objfs                   0    0    0    0% /system/object
sharefs                   0    0    0    0% /etc/dfs/sharetab
/platform/sun4u-us3/lib/libc_psr/libc_psr_hwcap2.so.1
                  25200403 4924932 20275471 20% /platform/sun4u-us3/lib/libc_psr.so.1
/platform/sun4u-us3/lib/sparcv9/libc_psr/libc_psr_hwcap2.so.1
                  25200403 4924932 20275471 20% /platform/sun4u-us3/lib/sparcv9/libc_psr.so.1
fd                      0    0    0    0% /dev/fd
rpool/ROOT/s10s_u7wos_08/var
                  58834944 74638 20275471    1% /var
swap                29943872    72 29943800    1% /tmp
swap                29943832    32 29943800    1% /var/run
rpool/export       58834944    20 20275471    1% /export
rpool/export/home 58834944    18 20275471    1% /export/home
rpool             58834944    94 20275471    1% /rpool
# zpool list
NAME SIZE USED  AVAIL CAP  HEALTH  ALTROOT
rpool 57G  20.8G  36.2G 36%  ONLINE  -
# zfs list
NAME                         USED  AVAIL  REFER  MOUNTPOINT
rpool                      36.8G  19.3G 94K  /rpool
rpool/ROOT                   4.77G  19.3G 18K  legacy
rpool/ROOT/s10s_u7wos_08    4.77G  19.3G  4.70G  /
rpool/ROOT/s10s_u7wos_08/var  72.9M  19.3G  72.9M  /var
rpool/dump                   16.0G  19.3G  16.0G  -
rpool/export                   38K  19.3G 20K  /export
rpool/export/home             18K  19.3G 18K  /export/home
rpool/swap                   16G  35.3G 16K  -

# stmsboot -L
stmsboot: MPxIO is not enabled
# stmsboot -e

警告：可以对每个受支持的具有多路径功能的控制器执行 stmsboot
      已在主机中检测到。在系统中，这些控制器为

/pci@7c,600000/SUNW,qlc@1/fp@0,0
/pci@7d,600000/SUNW,qlc@1/fp@0,0
/pci@7d,600000/SUNW,qlc@1,1/fp@0,0

如果您不希望对这些控制器执行操作，请退出 stmsboot
并使用 -D { fp | mpt } 重新调用以指定要针对哪些控制器
来修改多路径配置。

是否继续？[y/n]（缺省值：Y） y
警告：此操作将需要重新引导。
是否要继续？[y/n]（缺省值：y）y
这些更改将在重新引导系统后生效。
现在就重新引导系统吗？ [y/n]（缺省值：y） y
May 19 10:25:41 e20k-2-e reboot: rebooted by root
updating /platform/sun4u/boot_archive
May 19 10:25:48 e20k-2-e syslogd: going down on signal 15
syncing file systems... done
rebooting...

Resetting...

Sun Fire E20K, using IOSRAM based Console
Copyright 2007 Sun Microsystems, Inc.  All rights reserved.
OpenBoot 4.22.32, 16384 MB memory installed, Serial #44701348.
Ethernet address 0:0:be:aa:16:a4, Host ID: 82aa16a4.

Rebooting with command: boot
QLogic QLA2460 Host Adapter Driver(SPARC): 1.24  11/15/06
Firmware version 4.00.26
Boot device: /pci@7c,600000/SUNW,qlc@1/fp@0,0/disk@w50060e80044ee372,0:a  File and args:
SunOS Release 5.10 Version Generic_139555-08 64-bit
Copyright 1983-2009 Sun Microsystems, Inc.  All rights reserved.
Use is subject to license terms.
stmsboot: Root is on ZFS
stmsboot: configuring devices
Hostname: e20k-2-e
SUNW,eri0 : 100 Mbps half duplex link up

stmsboot: vfstab has been updated
stmsboot: dump on ZFS, no dumpadm update required
Reading ZFS config: done.
Mounting ZFS filesystems: (6/6)

e20k-2-e console login: rootMay 19 10:29:22 e20k-2-e sendmail[598]: My unqualified host name (e20k-2-e) unknown; sleeping for retry
May 19 10:29:22 e20k-2-e sendmail[597]: My unqualified host name (e20k-2-e) unknown; sleeping for retry

Password:
Last login: Tue May 19 10:16:08 on console
May 19 10:29:23 e20k-2-e login: ROOT LOGIN /dev/console
Sun Microsystems Inc. SunOS 5.10    Generic January 2005
# format
Searching for disks...done

AVAILABLE DISK SELECTIONS:
   0. c3t60060E80044EE30000004EE3000000B2d0 <HITACHI-OPEN-V-SUN-5008 cyl 15666 alt 2 hd 15 sec 512>
      /scsi_vhci/ssd@g60060e80044ee30000004ee3000000b2
   1. c3t60060E80044EE30000004EE3000000B9d0 <HITACHI-OPEN-V-SUN-5008 cyl 15666 alt 2 hd 15 sec 512>
      /scsi_vhci/ssd@g60060e80044ee30000004ee3000000b9
   2. c3t60060E80044EE30000004EE3000000BFd0 <HITACHI-OPEN-V-SUN-5008 cyl 15666 alt 2 hd 15 sec 512>
      /scsi_vhci/ssd@g60060e80044ee30000004ee3000000bf
   3. c3t60060E80044EE30000004EE3000000C7d0 <HITACHI-OPEN-V-SUN-5008 cyl 15666 alt 2 hd 15 sec 512>
      /scsi_vhci/ssd@g60060e80044ee30000004ee3000000c7
Specify disk (enter its number): ^D
# May 19 10:30:22 e20k-2-e sendmail[597]: unable to qualify my own domain name (e20k-2-e) -- using short name
May 19 10:30:22 e20k-2-e sendmail[598]: unable to qualify my own domain name (e20k-2-e) -- using short name
May 19 10:30:22 e20k-2-e sendmail[597]: [ID 702911 mail.alert] unable to qualify my own domain name (e20k-2-e) -- using short name
May 19 10:30:22 e20k-2-e sendmail[598]: [ID 702911 mail.alert] unable to qualify my own domain name (e20k-2-e) -- using short name

#
#

[ 本帖最后由 IT业的民工于 2009-6-1 21:45 编辑 ]

作者: IT业的民工 时间: 2009-06-01 15:38
把 E20K（san boot domain）上的一块HBA拔出来插的到E6900 上因为不想在调整hds上的map，启动在E20k 上安装好的solaris

ChassisSerialNumber 0740AK207D

Sun Fire E6900
OpenFirmware version 5.20.10 (05/21/08 16:12)
Copyright 2008 Sun Microsystems, Inc.  All rights reserved.
Use is subject to license terms.
SmartFirmware, Copyright (C) 1996-2001.  All rights reserved.
16384 MB memory installed, Serial #71398120.
Ethernet address 0:14:4f:41:72:e8, Host ID: 844172e8.

Rebooting with command: boot -sr
QLogic QLA2462 Host Adapter Driver(SPARC): 1.24  11/15/06
Firmware version 4 .0 0 .26
SunOS Release 5.10 Version Generic_139555-08 64-bit
Copyright 1983-2009 Sun Microsystems, Inc.  All rights reserved.
Use is subject to license terms.
Hardware watchdog enabled
Booting to milestone "milestone/single-user:default".
Failed to plumb IPv4 interface(s): dman0
Jun  1 10:12:13 svc.startd[7]: svc:/network/physical:default: Method "/lib/svc/method/net-physical" failed with exit status 96.
Jun  1 10:12:13 svc.startd[7]: network/physical:default misconfigured: transitioned to maintenance (see 'svcs -xv' for details)
Hostname: e20k-2-e
Configuring devices.
Requesting System Maintenance Mode
SINGLE USER MODE

Root password for system maintenance (control-d to bypass): svc.startd: Returning to milestone all.
/dev/rdsk/c3t60060E80044EE30000004EE3000000BFd0s4 is clean
Reading ZFS config: done.

e20k-2-e console login: Jun  1 10:13:06 svc.startd[7]: svc:/platform/sun4u/dcs:default: Method "/lib/svc/method/svc-dcs" failed with exit status 96.
Jun  1 10:13:07 svc.startd[7]: platform/sun4u/dcs:default misconfigured: transitioned to maintenance (see 'svcs -xv' for details)
Jun  1 10:13:07 svc.startd[7]: svc:/system/cvc:default: Method "/lib/svc/method/svc-cvcd" failed with exit status 96.
Jun  1 10:13:07 svc.startd[7]: system/cvc:default misconfigured: transitioned to maintenance (see 'svcs -xv' for details)
Jun  1 10:13:09 e20k-2-e sendmail[493]: My unqualified host name (e20k-2-e) unknown; sleeping for retry
Jun  1 10:13:09 e20k-2-e sendmail[494]: My unqualified host name (e20k-2-e) unknown; sleeping for retry

e20k-2-e console login: root
Password:
Last login: Sun May 31 17:40:04 on console
Jun  1 10:13:14 e20k-2-e login: ROOT LOGIN /dev/console
Sun Microsystems Inc. SunOS 5.10    Generic January 2005
# format
Searching for disks...done

AVAILABLE DISK SELECTIONS:
   0. c3t60060E80044EE30000004EE3000000B2d0 <HITACHI-OPEN-V-SUN-5008 cyl 15666 alt 2 hd 15 sec 512>
      /scsi_vhci/ssd@g60060e80044ee30000004ee3000000b2
   1. c3t60060E80044EE30000004EE3000000B9d0 <HITACHI-OPEN-V-SUN-5008 cyl 15666 alt 2 hd 15 sec 512>
      /scsi_vhci/ssd@g60060e80044ee30000004ee3000000b9
   2. c3t60060E80044EE30000004EE3000000BFd0 <HITACHI-OPEN-V-SUN-5008 cyl 15666 alt 2 hd 15 sec 512>
      /scsi_vhci/ssd@g60060e80044ee30000004ee3000000bf
   3. c3t60060E80044EE30000004EE3000000C7d0 <HITACHI-OPEN-V-SUN-5008 cyl 15666 alt 2 hd 15 sec 512>
      /scsi_vhci/ssd@g60060e80044ee30000004ee3000000c7
   4. c4t0d0 <SUN146G cyl 14087 alt 2 hd 24 sec 848>
      /ssm@0,0/pci@19,700000/pci@1/scsi@2/sd@0,0
   5. c4t1d0 <SUN146G cyl 14087 alt 2 hd 24 sec 848>
      /ssm@0,0/pci@19,700000/pci@1/scsi@2/sd@1,0
Specify disk (enter its number): ^D
# luxadm probe
No Network Array enclosures found in /dev/es

Found Fibre Channel device(s):
  Node WWN:50060e80044ee362  Device Type

isk device
Logical Path:/dev/rdsk/c3t60060E80044EE30000004EE3000000B2d0s2
Node WWN:50060e80044ee362 Device Type

isk device
Logical Path:/dev/rdsk/c3t60060E80044EE30000004EE3000000B9d0s2
Node WWN:50060e80044ee362 Device Type

isk device
Logical Path:/dev/rdsk/c3t60060E80044EE30000004EE3000000BFd0s2
Node WWN:50060e80044ee362 Device Type

isk device
Logical Path:/dev/rdsk/c3t60060E80044EE30000004EE3000000C7d0s2
#
# zpool import rpool
Jun  1 10:14:09 e20k-2-e sendmail[494]: unable to qualify my own domain name (e20k-2-e) -- using short name
Jun  1 10:14:09 e20k-2-e sendmail[493]: unable to qualify my own domain name (e20k-2-e) -- using short name
Jun  1 10:14:09 e20k-2-e sendmail[494]: [ID 702911 mail.alert] unable to qualify my own domain name (e20k-2-e) -- using short name
Jun  1 10:14:09 e20k-2-e sendmail[493]: [ID 702911 mail.alert] unable to qualify my own domain name (e20k-2-e) -- using short name
无法导入 'rpool'：其他系统可能正在使用池，该池最后由 Mon May 25 16:02:49 2009
上的 e20k-2-e（主机标识：0x82aa16a4）访问使用 '-f' 强制导入
# zpool import -f rpool
cannot mount '/export': directory is not empty
cannot mount '/export/home': directory is not empty
# zpool status
  池：rpool
状态：ONLINE
清理：未请求
配置：

      NAME                                     STATE    READ WRITE CKSUM
      rpool                                     ONLINE    0    0    0
      c3t60060E80044EE30000004EE3000000B2d0s0  ONLINE    0    0    0

错误：无已知的数据错误
# init 0
# svc.startd: The system is coming down.  Please wait.
svc.startd: 98 system services are now being stopped.
Jun  1 10:14:51 e20k-2-e syslogd: going down on signal 15
svc.startd: The system is down.
syncing file systems... done
NOTICE: f_client_exit: Program terminated!
debugger entered.
{216} ok reset-all
ChassisSerialNumber 0740AK207D

Sun Fire E6900
OpenFirmware version 5.20.10 (05/21/08 16:12)
Copyright 2008 Sun Microsystems, Inc.  All rights reserved.
Use is subject to license terms.
SmartFirmware, Copyright (C) 1996-2001.  All rights reserved.
16384 MB memory installed, Serial #71398120.
Ethernet address 0:14:4f:41:72:e8, Host ID: 844172e8.

{14} ok boot hds-lun0-b
QLogic QLA2462 Host Adapter Driver(SPARC): 1.24  11/15/06
Firmware version 4 .0 0 .26
SunOS Release 5.10 Version Generic_139555-08 64-bit
Copyright 1983-2009 Sun Microsystems, Inc.  All rights reserved.
Use is subject to license terms.
Hardware watchdog enabled
Failed to plumb IPv4 interface(s): dman0
Jun  1 10:24:26 svc.startd[7]: svc:/network/physical:default: Method "/lib/svc/method/net-physical" failed with exit status 96.
Jun  1 10:24:26 svc.startd[7]: network/physical:default misconfigured: transitioned to maintenance (see 'svcs -xv' for details)
Hostname: e20k-2-e
Jun  1 10:25:02 svc.startd[7]: svc:/system/cvc:default: Method "/lib/svc/method/svc-cvcd" failed with exit status 96.
Jun  1 10:25:02 svc.startd[7]: system/cvc:default misconfigured: transitioned to maintenance (see 'svcs -xv' for details)
Jun  1 10:25:02 svc.startd[7]: svc:/platform/sun4u/dcs:default: Method "/lib/svc/method/svc-dcs" failed with exit status 96.
Jun  1 10:25:02 svc.startd[7]: platform/sun4u/dcs:default misconfigured: transitioned to maintenance (see 'svcs -xv' for details)
Reading ZFS config: done.
Mounting ZFS filesystems: (6/6)

e20k-2-e console login: Jun  1 10:25:15 e20k-2-e picld[184]: SUNW_piclmemcfg init mc failed!

e20k-2-e console login: root
Password:
Jun  1 10:25:37 e20k-2-e login: ROOT LOGIN /dev/console
Last login: Mon May 25 15:59:08 on console
Sun Microsystems Inc. SunOS 5.10    Generic January 2005
# zpool status
  池：rpool
状态：ONLINE
清理：未请求
配置：

      NAME                                     STATE    READ WRITE CKSUM
      rpool                                     ONLINE    0    0    0
      c3t60060E80044EE30000004EE3000000B2d0s0  ONLINE    0    0    0

错误：无已知的数据错误
# format
Searching for disks...done

AVAILABLE DISK SELECTIONS:
   0. c3t60060E80044EE30000004EE3000000B2d0 <HITACHI-OPEN-V-SUN-5008 cyl 15666 alt 2 hd 15 sec 512>
      /scsi_vhci/ssd@g60060e80044ee30000004ee3000000b2
   1. c3t60060E80044EE30000004EE3000000B9d0 <HITACHI-OPEN-V-SUN-5008 cyl 15666 alt 2 hd 15 sec 512>
      /scsi_vhci/ssd@g60060e80044ee30000004ee3000000b9
   2. c3t60060E80044EE30000004EE3000000BFd0 <HITACHI-OPEN-V-SUN-5008 cyl 15666 alt 2 hd 15 sec 512>
      /scsi_vhci/ssd@g60060e80044ee30000004ee3000000bf
   3. c3t60060E80044EE30000004EE3000000C7d0 <HITACHI-OPEN-V-SUN-5008 cyl 15666 alt 2 hd 15 sec 512>
      /scsi_vhci/ssd@g60060e80044ee30000004ee3000000c7
Specify disk (enter its number): ^D
# uname -a
SunOS e20k-2-e 5.10 Generic_139555-08 sun4u sparc SUNW,Sun-Fire
# uanem -i
uanem: 没找到
# uanem -i
uanem: 没找到
# uname -i
SUNW,Sun-Fire
# prtidag
prtidag: 没找到
# prtdiag
系统配置：  Sun Microsystems  sun4u Sun Fire E6900
系统时钟频率：150 MHz
内存大小：16384 兆字节

========================= CPUs ===============================================

         CPU    Run E$ CPU    CPU
FRU Name ID    MHz MB Impl. Mask
----------  -------  ----  ----  -------  ----

========================= Memory Configuration ===============================

                  Logical  Logical  Logical
            Port  Bank    Bank    Bank       DIMM Interleave  Interleave
FRU Name       ID Num    Size    Status    Size Factor    Segment
-------------  ----  ----    ------ -----------  ------  ----------  ----------
/N0/SB5/P0/B0 20 0    1024MB pass       512MB 16-way    0
/N0/SB5/P0/B1 20 1    1024MB pass       512MB 16-way    0
/N0/SB5/P0/B0 20 2    1024MB pass       512MB 16-way    0
/N0/SB5/P0/B1 20 3    1024MB pass       512MB 16-way    0
/N0/SB5/P1/B0 21 0    1024MB pass       512MB 16-way    0
/N0/SB5/P1/B1 21 1    1024MB pass       512MB 16-way    0
/N0/SB5/P1/B0 21 2    1024MB pass       512MB 16-way    0
/N0/SB5/P1/B1 21 3    1024MB pass       512MB 16-way    0
/N0/SB5/P2/B0 22 0    1024MB pass       512MB 16-way    0
/N0/SB5/P2/B1 22 1    1024MB pass       512MB 16-way    0
/N0/SB5/P2/B0 22 2    1024MB pass       512MB 16-way    0
/N0/SB5/P2/B1 22 3    1024MB pass       512MB 16-way    0
/N0/SB5/P3/B0 23 0    1024MB pass       512MB 16-way    0
/N0/SB5/P3/B1 23 1    1024MB pass       512MB 16-way    0
/N0/SB5/P3/B0 23 2    1024MB pass       512MB 16-way    0
/N0/SB5/P3/B1 23 3    1024MB pass       512MB 16-way    0

========================= IO 卡 =========================

                              Bus  Max
         IO Port Bus    Freq Bus  Dev,
FRU Name Type  ID  Side Slot MHz  Freq Func State Name                            Model
----------  ---- ---- ---- ---- ---- ---- ---- ----- --------------------------------  ----------------------
/N0/IB6/P0  PCI 24 B 1 33 33  2,0  ok SUNW,qlc-pci1077,141.1077.141.2/+ QLA2462
/N0/IB6/P0  PCI 24 B 1 33 33  2,1  ok SUNW,qlc-pci1077,141.1077.141.2/+ QLA2462
/N0/IB6/P0  PCI 24 A 2 66 66  2,0  ok SUNW,qlc-pci1077,140.1077.140.2/+ QLA2460
/N0/IB6/P1  PCI 25 B 4 66 66  1,0  ok pci-pci8086,b154.0/network (netw+ pci-bridge
/N0/IB6/P1  PCI 25 B 4 66 66  0,0  ok network-pci100b,35.30          SUNW,pci-ce
/N0/IB6/P1  PCI 25 B 4 66 66  1,0  ok network-pci100b,35.30          SUNW,pci-ce
/N0/IB6/P1  PCI 25 B 4 66 66  2,0  ok scsi-pci1000,b.7/disk (block)
/N0/IB6/P1  PCI 25 B 4 66 66  2,1  ok scsi-pci1000,b.7/disk (block)
/N0/IB6/P1  PCI 25 A 6 66 66  2,0  ok pci-pci8086,537c.7/network (netw+ pci-bridge
/N0/IB6/P1  PCI 25 A 6 66 66  0,0  ok network-pci100b,35.30          SUNW,pci-x-qge
/N0/IB6/P1  PCI 25 A 6 66 66  1,0  ok network-pci100b,35.30          SUNW,pci-x-qge
/N0/IB6/P1  PCI 25 A 6 66 66  2,0  ok network-pci100b,35.30          SUNW,pci-x-qge
/N0/IB6/P1  PCI 25 A 6 66 66  3,0  ok network-pci100b,35.30          SUNW,pci-x-qge
/N0/IB8/P0  PCI 28 A 2 66 66  2,0  ok SUNW,qlc-pci1077,140.1077.140.2/+ QLA2460
/N0/IB8/P1  PCI 29 B 4 66 66  1,0  ok pci-pci8086,537c.7/network (netw+ pci-bridge
/N0/IB8/P1  PCI 29 B 4 66 66  0,0  ok network-pci100b,35.30          SUNW,pci-x-qge
/N0/IB8/P1  PCI 29 B 4 66 66  1,0  ok network-pci100b,35.30          SUNW,pci-x-qge
/N0/IB8/P1  PCI 29 B 4 66 66  2,0  ok network-pci100b,35.30          SUNW,pci-x-qge
/N0/IB8/P1  PCI 29 B 4 66 66  3,0  ok network-pci100b,35.30          SUNW,pci-x-qge

========================= 网域的激活板 ===========================

         Board       Receptacle Occupant
FRU Name Type       Status       Status       Condition Info
---------  -----------  ----------- ------------  --------- ----------------------------------------
/ssm0:N0/SB5  CPU_V3    connected    configured ok       powered-on, assigned
/ssm0:N0/IB6  PCI+_I/O_Bo  connected    configured ok       powered-on, assigned
/ssm0:N0/IB7  PCI+_I/O_Bo  connected    configured ok       powered-on, assigned
/ssm0:N0/IB8  PCI+_I/O_Bo  connected    configured ok       powered-on, assigned
/ssm0:N0/IB9  PCI+_I/O_Bo  connected    configured ok       powered-on, assigned

========================= 网域的激活板/界面槽 ===========================

         Board       Receptacle Occupant
FRU Name Type       Status       Status       Condition Info
---------  -----------  ----------- ------------  --------- ----------------------------------------
/ssm0:N0/SB0  unknown    empty       unconfigured  unknown assigned
/ssm0:N0/SB1  unknown    empty       unconfigured  unknown assigned
/ssm0:N0/SB2  unknown    empty       unconfigured  unknown assigned
/ssm0:N0/SB3  unknown    empty       unconfigured  unknown assigned
/ssm0:N0/SB4  unknown    empty       unconfigured  unknown assigned

========================= 硬件故障 ==================================
系统中未发现硬件故障

#

[ 本帖最后由 IT业的民工于 2009-6-1 15:39 编辑 ]

作者: heroesray 时间: 2009-06-01 15:54
不错，hba卡后换的吧，原先项目中装过一个12khba卡型号就比较老。
solu7是一个什么东东啊？
还有个问题不是san-boot的，就是sms-svc用户命令里面有没有什么命令是类似4900 or 6900那样的直接break命令停止操作系统到ok状态下？一般系统有问题不停重启只能setobpparam设置auto-boot? false，在setkeyswitch -d a off在on后修复操作系统，加电自检时间太长了。感觉sun越高端的机器越难用。

作者: 风之幻想 时间: 2009-06-01 15:58
收藏了。谢谢楼主！！！！

作者: IT业的民工 时间: 2009-06-01 21:41
标题: 回复 #3 heroesray 的帖子
solu7是一个什么东东啊？  solaris10 u7

就是sms-svc用户命令里面有没有什么命令是类似4900 or 6900那样的直接break命令停止操作系统到ok状态下？
  that directs console to perform some special action, as fol-
   lows:

   ~? Status message.

   ~. Disconnect console session.

   ~# Break to OpenBoot PROM or kadb.

   ~@ Acquire unlocked write permission; see -g.

   ~^ Release write permission.

   ~= Toggle the communication path between the network  and
         IOSRAM interfaces. You can use ~= only in Private mode
         (see ~*).

   ~& Acquire locked write permission; see -l. You can issue
         this  signal during a read-only or unlocked write ses-
         sion.

   ~* Acquire locked write permission, terminate  all  other
         open  sessions,  and  prevent  new sessions from being
         opened; see  -f.  To  restore  multiple-session  mode,
         either release the lock or terminate this session.

      Note:

作者: guopy007 时间: 2009-06-01 22:43
学习。。这么大的机器。。都在想象中的，没见过

作者: brucewoo 时间: 2009-06-01 23:48
不错,学习一下.

作者: nimysun 时间: 2009-06-02 09:38
还没见过这么大的家伙，羡慕啊～～

作者: 风之幻想 时间: 2009-06-02 09:41
版主，建议加精华

作者: 要努力学习 时间: 2009-06-02 11:01
没搞过

作者: killer911 时间: 2009-06-02 12:32
Domain配置比较低，一系统板，一个IO板

作者: 山野村夫 时间: 2009-06-02 12:54
20k还木有摸过

作者: midc 时间: 2009-06-05 17:46
在中国,除了原厂的,一般没必要去学习E6900以上的机器.用户除外

作者: maike_xiao 时间: 2009-06-06 09:10
以前只看过介绍说可以SAN BOOT，今天还真有人做了，不错！
这样就可以省好几个D240了，呵呵，不知道有没有实际项目中这样用的？

作者: alex_linux 时间: 2009-06-06 15:03
好.支持

[ 本帖最后由 alex_linux 于 2009-6-6 15:10 编辑 ]

作者: 孔方兄 时间: 2009-06-06 17:50
前面做了一套SAN boot，硬件如下：

M4000一台满配，一台半配；富士通出来的，所以带两块富士通双口网两块卡，富士通双口HBA卡两块；阵列是富士通E4K
,另外准备了一块intel的4口网卡和两块qlogic的2462 HBA卡备用；

结果发现落入了兼容性陷阱：

想用M4000的硬件分区+SAN Boot+VCS+MPXIO+ZFS；结果发现有问题;

1. 富士通的HBA不支持MPXIO；阵列支持的，前面也用过；
2. 要用富士通的阵列SAN boot，怎HBA卡要求是富士通的；厂商的兼容性列表和测试过的；
3. M4000的第二个分区没有内置硬盘，安装用Boot net，又要求是用富士通的网卡，且不支持sol10 U5以后的版本。。。贝准备了U7的flar，结果不能用。

总之发下不少兼容性的问题。。。。

M4000的设计弱智的地方挺多，这么大的机器就2个内置硬盘；分区功能限制很多，如果内存条数配得不够，可能有CPU不能用。。

还好不急用，可以慢慢的折腾。。。。

作者: nimysun 时间: 2009-06-06 20:08
ls的事情应该找售前，肯定是他们的方案做到不到位

作者: easybegin 时间: 2009-06-07 12:23
生产环境不知到SAN boot用的多吗？可靠吗？容易维护吗？

欢迎光临 Chinaunix (http://bbs.chinaunix.net/)