思科VSS虚拟交换系统详细配置命令
步聚
6509-1配置
第一步、
初始化Catalyst 6509交换机
VSS-sw1#conf t
Enter configuration commands, one
per line. End with CNTL/Z.
6509-2配置
VSS-sw2#conf t
Enter configuration commands, one
per line. End with CNTL/Z.
第二步、
配置VSS Domain ID；
VSS-sw1(config)#switch virtual domain 100
Domain ID 100 config will take
effect only
after the exec command ‘switch
convert mode virtual’ is issued
6509-2配置
VSS-sw2(config)#switch virtual domain 100
Domain ID 100 config will take
effect only
after the exec command ‘switch
convert mode virtual’ is issued
第三步、
设置交换机Switch ID；
VSS-sw1#switch read switch_num
Read switch_num from rommon is 1
6509-2配置
VSS-sw2#switch read switch_num
Read switch_num from rommon is 2
第五步、
配置VSL；
VSS-sw1#conf t
Enter configuration commands, one
per line. End with CNTL/Z.
VSS-sw1(config)#interface portchannel 1
VSS-sw1(config-if)#switch virtual link 1
VSS-sw1(config-if)#no shut
VSS-sw1(config-if)#
6509-2配置
VSS-sw2#conf t
Enter configuration commands, one
per line. End with CNTL/Z.
VSS-sw2(config)#interface portchannel 2
VSS-sw2(config-if)#switch virtual link 2
VSS-sw2(config-if)#no shut
VSS-sw2(config-if)#
物理接口划入端口组
VSS-sw1(config)#interface range tenGigabitEthernet 5/4 - 5
VSS-sw1(config-if-range)#channelgroup 1 mode on
VSS-sw1(config-if-range)#no shut
VSS-sw1(config-if-range)#^Z
VSS-sw1#
Switch-1# platform hardware vsl pfc mode pfc3c
6509-2配置
VSS-sw2(config)#interface range tenGigabitEthernet 5/4 - 5
VSS-sw2(config-if-range)#channelgroup 2 mode on
VSS-sw2(config-if-range)#no shut
VSS-sw2(config-if-range)#^Z
VSS-sw2#
VSS-sw1#switch convert mode virtual
This command will convert all
interface names to naming
convention “interface-type
switch-number/slot/port”, save
the running config to startupconfig
and reload the switch.
Do you want to proceed? [yes/no]: yes
Converting interface names
Building configuration...
[OK]
Saving converted configurations
to bootflash …
[OK]
6509-2配置
VSS-sw2#switch convert mode virtual
This command will convert all
interface names to naming
convention “interface-type
switch-number/slot/port”, save
the running config to startupconfig
and reload the switch.
Do you want to proceed? [yes/no]: yes
Converting interface names
Building configuration...
[OK]
Saving converted configurations
to bootflash…
[OK]
第七步、
重启交换机
System detected Virtual Switch
configuration...
Interface TenGigabitEthernet1/5/4 is member of PortChannel 1
Interface TenGigabitEthernet1/5/5 is member of PortChannel 1
00:00:26: %VSL_BRINGUP-6-
MODULE_UP: VSL module in slot 5
switch 1 brought up
Initializing as Virtual Switch Active
00:08:01: SW1_SP: Card inserted in
Switch_number = 2 ,
physical slot 3,
interfaces are now online
VSS >
VSS>en
VSS#
6509-2配置
System detected Virtual Switch
configuration...
Interface TenGigabitEthernet2/5/4 is member of PortChannel 2
Interface TenGigabitEthernet2/5/5 is member of PortChannel 2
00:00:26: %VSL_BRINGUP-6-
MODULE_UP: VSL module in slot 5
switch 2 brought up
Initializing as Virtual Switch standby
00:01:43: %CRYPTO-6-ISAKMP_ON_OFF:
ISAKMP is OFF
00:01:43: %CRYPTO-6-ISAKMP_ON_OFF:
ISAKMP is OFF
VSS-sdby>
Standby console disabled
第八步、
检验VSS配置
VSS#show switch virtual
Switch mode : Virtual Switch
Virtual switch domain number : 100
Local switch number : 1
Local switch operational role: Virtual Switch Active
Peer switch number : 2
Peer switch operational role : Virtual Switch Standby
vss(config)# interface port-channel 20
vss(config-if)# shutdown
vss(config-if)# exit
vss(config)# switch virtual domain 100
vss(config-vs-domain)# dual-active detection pagp
vss(config-vs-domain)# dual-active detection pagp trust channel-group 20
vss(config-vs-domain)# exit
vss(config)# interface port-channel 20
vss(config-if)# no shutdown
vss(config-if)# exit
vss#conf t
Enter configuration commands, one per line. End with CNTL/Z.
vss(config)#switch virtual domain 100
vss(config-vs-domain)#dual-active detection pagp
vss(config-vs-domain)#dual-active trust channel-group 20
vss(config-vs-domain)#
BFD配置，
试验是成功的。
vss (config)# interface gigabitethernet 1/5/3
vss (config-if)# no switchport
vss(config-if)# ip address 200.230.230.231 255.255.255.0
vss (config-if)# bfd interval 100 min_rx 100 multiplier 50
vss (config-if)# no shutdown
vss(config-if)# interface gigabitethernet 2/5/3
vss(config-if)# no switchport
vss(config-if)# ip address 201.230.230.231 255.255.255.0
vss (config-if)# bfd interval 100 min_rx 100 multiplier 50
vss(config-if)# no shutdown
vss(config-if)# exit
vss (config)# switch virtual domain 100
vss (config-vs-domain)# dual-active detection bfd
vss (config-vs-domain)# dual-active pair interface g 1/9/48 interface g 2/1/48 bfd
adding a static route 200.230.230.0 255.255.255.0 Gi2/1/48 for this dual-active pair adding a static route 201.230.230.0 255.255.255.0 Gi1/9/48 for this dual-active pair
vss(config-vs-domain)# exit
vss(config)# exit
vss# show switch virtual dual-active bfd
Bfd dual-active detection enabled: Yes Bfd dual-active interface pairs configured: interface1 Gi1/9/48 interface2 Gi2/1/48
设置两台交换机的priority
vss#conf t
Enter configuration commands, one per line. End with CNTL/Z.
vss(config)#switch virtual domain 100
vss(config-vs-domain)#switch 1 priority 110
*Jul 7 08:59:11.913: %VSLP-SW1_SPSTBY-5-RRP_RT_CFG_CHANGE: Configured
priority value
is different from operational value.
Change will take effect after config is saved and switch is reloaded.
vss(config-vs-domain)#switch 2 priority 100
vss(config-vs-domain)#^Z
vss#
第十一步、
保存配置
vss#conf t
Enter configuration commands, one per line. End with CNTL/Z.
vss(config)#wr