Enter cluster name [Cluster]:Cluster
Enter IP address for cluster alias [x.x.x.x]: 10.0.0.3
--------------------------------
Information for Cluster Member 0
--------------------------------
Enter name of cluster member [storage0]: node1
Looking for host storage0 (may take a few seconds)...
Enter number of heartbeat channels (minimum = 1) [1]: 1
Information about Channel 0
Channel type: net or serial [net]:
Enter hostname of the cluster member on heartbeat channel 0 \
[node1]: node1
Looking for host node1 (may take a few seconds)...
Information about Quorum Partitions
Enter Primary Quorum Partition [/dev/raw/raw1]: /dev/raw/raw1
Enter Shadow Quorum Partition [/dev/raw/raw2]: /dev/raw/raw2
Information About the Power Switch That Power Cycles Member ’storage0’
Choose one of the following power switches:
o NONE
o RPS10
o BAYTECH
o APCSERIAL
o APCMASTER
o WTI_NPS
Power switch [NONE]: NONE
Information for Cluster Member 1
--------------------------------
Enter name of cluster member [node2]: node2
Looking for host storage1 (may take a few seconds)...
Information about Channel 0
Enter hostname of the cluster member on heartbeat channel 0 \
[node2]: node2
Looking for host storage1 (may take a few seconds)...
Information about Quorum Partitions
Enter Primary Quorum Partition [/dev/raw/raw1]: /dev/raw/raw1
Enter Shadow Quorum Partition [/dev/raw/raw2]: /dev/raw/raw2
Information About the Power Switch That Power Cycles Member ’node2’
Choose one of the following power switches:
o NONE
o RPS10
o BAYTECH
o APCSERIAL
o APCMASTER
o WTI_NPS
Power switch [NONE]: NONE
Cluster name: Development Cluster
Cluster alias IP address: 10.0.0.154
Cluster alias netmask: 255.255.254.0
--------------------
Member 0 Information
--------------------
Name: node1
Primary quorum partition: /dev/raw/raw1
Shadow quorum partition: /dev/raw/raw2
Heartbeat channels: 1
Channel type: net, Name: node1
Power switch IP address or hostname: node1
--------------------
Member 1 Information
--------------------
Name: node2
Primary quorum partition: /dev/raw/raw1
Shadow quorum partition: /dev/raw/raw2
Heartbeat channels: 1
Channel type: net, Name: node2
Save the cluster member information? yes/no [yes]:
Writing to configuration file...done
Configuration information has been saved to /etc/cluster.conf.
----------------------------
Setting up Quorum Partitions
----------------------------
Running cludiskutil -I to initialize the quorum partitions: done
Saving configuration information to quorum partitions: done
Do you wish to allow remote monitoring of the cluster? yes/no \
[yes]: yes
----------------------------------------------------------------
Configuration on this member is complete.
To configure the next member, invoke the following command on that system:
# /sbin/cluconfig --init=/dev/raw/raw1
See the manual to complete the cluster installation
3．配制第二个节点
只需执行 cluconfig --init=/dev/raw/raw1
4．启动Cluster服务
分别在两个节点上执行 service cluster start
你将看到下面的几个Daemon
• cluquorumd — Quorum daemon
• clusvcmgrd — Service manager daemon
• clupowerd — Power daemon
• cluhbd — Heartbeat daemon
• clumibd — Administrative system monitoring daemon
Service name: samba à所有黑色字体代表手工输入接受其默认值
Preferred member [None]:Node1 à这行代表Samba服务将默认在node1上运行。
Relocate when the preferred member joins the cluster (yes/no/?) [no]: yes
User script (e.g., /usr/foo/script or None) [None]:
Status check interval [0]: 10
Do you want to add an IP address to the service (yes/no/?) [no]: yes
IP Address Information
IP address: 10.0.0.10 à这行代表Samba服务运行的IP地址，即windows客户端访问输入的IP地址。
Netmask (e.g. 255.255.255.0 or None) [None]:
Broadcast (e.g. X.Y.Z.255 or None) [None]:
Do you want to (a)dd, (m)odify, (d)elete or (s)how an IP address, or
are you (f)inished adding IP addresses [f]:f
Do you want to add a disk device to the service (yes/no/?) [no]: yes
Disk Device Information
Device special file (e.g., /dev/sdb4): /dev/sdb3
Filesystem type (e.g., ext2, ext3 or None): ext3
Mount point (e.g., /usr/mnt/service1) [None]: /data à这行代表真正共享的存放地。
Mount options (e.g., rw,nosuid,sync): rw,nosuid,sync
Forced unmount support (yes/no/?) [yes]:
Would you like to allow NFS access to this filesystem (yes/no/?)\
[no]: no
Would you like to share to Windows clients (yes/no/?) [no]: yes
You will now be prompted for the Samba configuration:
Samba share name: samba –>;这行即windows客户端在网上邻居看到的名字。
The samba config file /etc/samba/smb.conf.samba does not exist.
Would you like a default config file created (yes/no/?) [no]: yes
Successfully created daemon lock directory /var/cache/samba/acct.
Please run ‘mkdir /var/cache/samba/samba‘ on the other cluster member.
Successfully created /etc/samba/smb.conf.samba.
Please remember to make necessary customizations and then copy the file
over to the other cluster member.
Do you want to (a)dd, (m)odify, (d)elete or (s)how DEVICES, or
are you (f)inished adding DEVICES [f]: f
name: samba
preferred node:node1
relocate: yes
user script: None
monitor interval: 30
IP address 0: 10.0.0.10
netmask 0: None
broadcast 0: None
device 0: /dev/sdb12
mount point, device 0: /mnt/users/accounting
mount fstype, device 0: ext2
mount options, device 0: rw,nosuid,sync
force unmount, device 0: yes
samba share, device 0: samba
Add samba_acct service as shown? (yes/no/?) yes
V220S和SCSI cable