Chinaunix

标题: rx6600固件与硬件问题，开不了机 [打印本页]

作者: coologin 时间: 2011-12-26 17:46
标题: rx6600固件与硬件问题，开不了机

上周对RX6600做过一次除尘操作，插插拔拔了一次。本周开机报如下错误。其中显示有固件错误，没有内存，对于固件错误，我按网上做法清除BMC密码，重启故障依旧，是否是硬件出了问题？

[rx6600mp] MP>

.....

Log Entry 18: 26 Dec 2011 09:44:09
Alert Level 7: Fatal
Keyword: BOOT_HALT_CELL
Cell or system halt
Logged by: System Firmware  0
Data: Major change in system state
0xF480003700E00190 000000000000000F

Log Entry 17: 26 Dec 2011 09:44:09
Alert Level 5: Critical
Keyword: SYSTEM_FIRMWARE_ERROR
System firmware error
Logged by: Redundant w/ an E0 code;
Sensor: System Firmware Progress
Data2: PRV State: 0x3F
0xC14EF841E9020180 FF3F4070000F0300

MP:SL (+,-,<CR>,D, F, L, J, H, K, T, A, U, ? for Help, Q or Ctrl-B to Quit) >

Log Entry 16: 26 Dec 2011 09:44:09
Alert Level 7: Fatal
Keyword: MEM_NO_MEM_FOUND
No memory found
Logged by: System Firmware  0
Data: Data field unused
0xE08000D100E00160 0000000000000000

Log Entry 15: 26 Dec 2011 09:44:05
Alert Level 5: Critical
Keyword: SYSTEM_FIRMWARE_ERROR
System firmware error
Logged by: Redundant w/ an E0 code;
Sensor: System Firmware Progress
Data2: PRV State: 0x3F
0xC14EF841E5020150 FF3F4070000F0300

MP:SL (+,-,<CR>,D, F, L, J, H, K, T, A, U, ? for Help, Q or Ctrl-B to Quit) >

Log Entry 6: 26 Dec 2011 09:43:19
Alert Level 5: Critical
Keyword: VOLTAGE_DEGRADES_TO_NON_RECOVERABLE
Voltage degraded to non-recoverable level - Check all boards with this voltage.
Logged by: Baseboard Management Controller;
Sensor: Voltage - 0.9V - Mem Ext 0
Data1: transition to Non-recoverable from less severe
0x204EF841B7020070 FFFF030768020300

通过如下命令进入，发提示：

[rx6600mp] MP> co

      [Use Ctrl-B or ESC-( to return to MP main menu.]

- - - - - - - - - - Prior Console Output - - - - - - - - - -
System going down IMMEDIATELY

System shutdown time has arrived

sync'ing disks (0 buffers to flush):
0 buffers not flushed
0 buffers still dirty

Closing open logical volumes...
Done

- - - - - - - - - - - - Live Console - - - - - - - - - - - -

作者: lbseraph 时间: 2011-12-26 20:46
和固件、console的信息无关，检查内存扩展板~重新检查板上的针脚、没问题再插拔一次。如果还不行很大可能是因为这板上0.9V的电压输出有问题，导致内存没法识别，才有固件报错的。

作者: coologin 时间: 2011-12-27 12:21
非常感谢，我再次把内存重插拔了一次，OK了。
昨天插拔具体不对。
谢谢

作者: lbseraph 时间: 2011-12-27 21:11
恢复就好~下次碰到应该就会小心了:wink:

作者: EN_LIJ 时间: 2011-12-31 15:35
虚惊呀！

作者: tangye 时间: 2012-01-05 19:54
还好!

作者: michael_023 时间: 2012-03-15 22:27
硬件也折腾人哩

欢迎光临 Chinaunix (http://bbs.chinaunix.net/)