选择:Options → Server Configuration... → Select the Server Options tab
Default Configuration: HP-UX B.1x.xx Default
Client Timeouts: 40
Run client installation UI on: server
选择: Options → Server Configurations... → Session Options
确认下面两个选项是否设置了:
Confirm new clients
Show the welcome screen for the install server
确保Halt the client after installation选项没有设置。
测试tftp是否可以正常工作的方法:
# cd /tmp
# tftp localhost
tftp> get /opt/ignite/Version
tftp> quit
# ll Version
检查nfs服务器是否启动。
由于使用Ignite server要用到nfs,所以nfs server必须enabled。
执行SAM,进入Networking and Communication,选择Networked File Systems,选择Exported Local File Systems,在Action菜单处选择Enable NFS Server。
四、 创建vPars:
1、 创建第一个vPar(这里我们假设第一个vPar的名字为vpar1,一共有三个vpar):
通过vparcreate命令创建第一个分区:
# vparcreate -p vpar1 -a cpu::2 -a cpu:::2:4 –a cpu:41 -a cpu:45 –a mem::1280 –a io:0.0 -a io:0.4 –a io:0.0.0.0.5.0:BOOT –a io:0.0.0.0.6.0:altboot
命令参数说明如下:
-p vpar1:分区名;
-a cpu::2:分区中包含的CPU数;
-a cpu:::2:4:分区中邦定的CPU数和最大可包含的CPU数;
–a cpu:41 -a cpu:45:分区中邦定的CPU的硬件路径(可以不指定,由系统自动分配);
–a mem::1280:分区中包含的内存数;
–a io:0.8 -a io:1.10:分区中包含的LBA的硬件路径(所有属于这些LBA卡的I/O设备都是这个分区的资源);
–a io:0.8.0.0.5.0:boot:分区的启动设备路径(启动磁盘路径,一定要包含已安装了操作系统的磁盘);
–a io:0.8.0.0.6.0:altboot:分区的替代启动设备路径(静像磁盘路径);
通过vparcreate命令创建剩余的vpar:
# vparcreate -p vpar2 -a cpu::2 -a cpu:::2 -a cpu:41 -a cpu:45 -a mem::1280 -a io:0.8 -a io:1.10 -a io:0/8/0/0.5.0:BOOT
# vparcreate -p vpar3 -a cpu::1 -a cpu:::1 -a mem::1280 -a io:0.5 -a io:1.4 –a io:1/4/0/0.5.0:BOOT
也可以通过文件来创建vPar:
# vi /stand/vpar1.opts
输入如下内容:
-p vpar1 \\
-a cpu::2 \\
-a cpu:::2:4 \\
-a cpu:41 \\
-a cpu:45 \\
-a mem::1280 \\
-a io:0.0 \\
-a io:0.4 \\
-a io:0.0.0.0.5.0:boot \\
-a io:0.0.0.0.6.0:altboot
然后执行vparcreate命令:
# vparcreate `cat /stand/vpar1.opts`