Chinaunix

标题: 请教：Cannot talk to PS0. Please check AC input and/or power switch [打印本页]

作者: guinanhai 时间: 2009-07-28 11:27
标题: 请教：Cannot talk to PS0. Please check AC input and/or power switch
目前SUN 4800 CPU板：1，电源：1\r\n现新加一块CPU板，poweron sb2的时候提示：\r\nbotsc-1:SC> poweron SB2\r\nSB2: cannot be powered on without adequate power; SB2 has an expected load of 660 which raises the total grid load to 1,925 but the supported load is only 1,610 \r\n\r\n换上另一台的电源，提示\r\nJul 27 18:06:00 botsc-1 Platform.SC: [ID 528287 local0.error] Cannot talk to PS0. Please check AC input and/or power switch.\r\nJul 27 18:15:07 botsc-1 Platform.SC: [ID 188222 local0.notice] /N0/SB2, hotplug status, SB2, module inserted (9,17)\r\nJul 27 19:05:50 botsc-1 Platform.SC: [ID 528287 local0.error] Cannot talk to PS0. Please check AC input and/or power switch.\r\n\r\n请大虾们帮忙看看。我是新手。\r\n\r\nbotsc-1:SC> showboards\r\n\r\nSlot Pwr Component Type State Status Domain\r\n---- --- -------------- ----- ------ ------\r\nSSC0 On System Controller Main Passed - \r\nID0 On Sun Fire 4800 Centerplane - OK - \r\nPS0 Off No Grid Power - - - \r\nPS1 On A153 Power Supply - OK - \r\nFT1 On Fan Tray High Speed OK - \r\nFT2 On Fan Tray High Speed OK - \r\nRP0 On Repeater Board - OK - \r\nRP2 On Repeater Board - OK - \r\nSB2 Off CPU Board V2 Available Not tested Isolated\r\n/N0/SB4 On CPU Board V2 Active Passed A\r\n/N0/IB6 On PCI I/O Board Active Passed A\r\n/N0/IB8 On PCI I/O Board Active Passed A\r\n\r\nbotsc-1:SC> showboards -v\r\n\r\nSlot Pwr Component Type State Status Domain\r\n---- --- -------------- ----- ------ ------\r\nSSC0 On System Controller Main Passed - \r\nSSC1 - Empty Slot - - - \r\nID0 On Sun Fire 4800 Centerplane - OK - \r\nPS0 Off No Grid Power - - - \r\nPS1 On A153 Power Supply - OK - \r\nPS2 - Empty Slot - - - \r\nFT0 - Empty Slot - - - \r\nFT1 On Fan Tray High Speed OK - \r\nFT2 On Fan Tray High Speed OK - \r\nRP0 On Repeater Board - OK - \r\nRP2 On Repeater Board - OK - \r\nSB0 - Empty Slot Assigned - A\r\nSB2 Off CPU Board V2 Available Not tested Isolated\r\n/N0/SB4 On CPU Board V2 Active Passed A\r\n/N0/IB6 On PCI I/O Board Active Passed A\r\n/N0/IB8 On PCI I/O Board Active Passed A\r\n\r\n\r\nComponent J-No. Size Reason \r\n--------- ----- ---- ------ \r\nSB2 - - No board power \r\n/N0/SB4/P0/B0/D0 J13300 256 MB \r\n/N0/SB4/P0/B0/D1 J13400 256 MB \r\n/N0/SB4/P0/B0/D2 J13500 256 MB \r\n/N0/SB4/P0/B0/D3 J13600 256 MB \r\n/N0/SB4/P0/B1 - - DRAM DIMM Group 1 Empty \r\n/N0/SB4/P1/B0/D0 J14300 256 MB \r\n/N0/SB4/P1/B0/D1 J14400 256 MB \r\n/N0/SB4/P1/B0/D2 J14500 256 MB \r\n/N0/SB4/P1/B0/D3 J14600 256 MB \r\n/N0/SB4/P1/B1 - - DRAM DIMM Group 1 Empty \r\n/N0/SB4/P2/B0/D0 J15300 256 MB \r\n/N0/SB4/P2/B0/D1 J15400 256 MB \r\n/N0/SB4/P2/B0/D2 J15500 256 MB \r\n/N0/SB4/P2/B0/D3 J15600 256 MB \r\n/N0/SB4/P2/B1 - - DRAM DIMM Group 1 Empty \r\n/N0/SB4/P3/B0/D0 J16300 256 MB \r\n/N0/SB4/P3/B0/D1 J16400 256 MB \r\n/N0/SB4/P3/B0/D2 J16500 256 MB \r\n/N0/SB4/P3/B0/D3 J16600 256 MB \r\n/N0/SB4/P3/B1 - - DRAM DIMM Group 1 Empty \r\n\r\n\r\nComponent Segment Compatible In Date Time Build Version \r\n--------- ------- ---------- -- ---- ---- ----- ------- \r\nSSC0/FP0 - - - - - - RTOS version: 26 \r\nSSC0/FP1 ScApp Reference 12 01/28/2003 13:31 1.0 5.14.4 \r\nSSC0/FP1 Ver - - 01/28/2003 13:31 1.0 5.14.4 \r\nSB2/FP0 - - - - - - No board power \r\nSB2/FP1 - - - - - - No board power \r\n/N0/IB6/FP0 iPOST Yes 12 09/26/2004 20:06 1.0 5.17.3 \r\n/N0/IB6/FP0 Ver - - 09/26/2004 20:10 1.0 5.17.3 \r\n/N0/IB8/FP0 iPOST Yes 12 03/22/2005 10:24 1.0 5.18.2 \r\n/N0/IB8/FP0 Ver - - 03/22/2005 10:33 1.0 5.18.2 Build_01 \r\n/N0/SB4/FP0 POST Yes 12 08/13/2004 11:53 1.0 5.17.2 \r\n/N0/SB4/FP0 OBP Yes 12 08/13/2004 11:52 1.0 5.17.2 \r\n/N0/SB4/FP0 Ver - - 08/13/2004 11:56 1.0 5.17.2 \r\n/N0/SB4/FP1 POST Yes 12 08/13/2004 11:53 1.0 5.17.2 \r\n/N0/SB4/FP1 OBP Yes 12 08/13/2004 11:52 1.0 5.17.2 \r\n/N0/SB4/FP1 Ver - - 08/13/2004 11:56 1.0 5.17.2 \r\n\r\n\r\nComponent SSC0 Signal SSC1 Signal Signal Used Failover \r\n--------- ----------- ----------- ----------- -------- \r\nSSC0 OK Failed SSC0 Disabled \r\nRP0 OK Failed SSC0 Disabled \r\nRP2 OK Failed SSC0 Disabled \r\nSB2 - - - - \r\n/N0/SB4 OK Failed SSC0 Disabled \r\n/N0/IB6 OK Failed SSC0 Disabled \r\n/N0/IB8 OK Failed SSC0 Disabled \r\n\r\n\r\nSlot Populated Slot Description\r\n---- --------- ----------------\r\n/N0/IB6/P0/B1/C0 Yes 33MHz. 5V Short PCI card\r\n/N0/IB6/P0/B1/C1 Empty 33MHz. 5V Short PCI card\r\n/N0/IB6/P0/B1/C2 Empty 33MHz. 5V Long/Short PCI card\r\n/N0/IB6/P0/B0/C3 Empty 66/33MHz. 3.3V Long/Short PCI card\r\n/N0/IB6/P1/B1/C4 Empty 33MHz. 5V Long/Short PCI card\r\n/N0/IB6/P1/B1/C5 Empty 33MHz. 5V Long/Short PCI card\r\n/N0/IB6/P1/B1/C6 Empty 33MHz. 5V Long/Short PCI card\r\n/N0/IB6/P1/B0/C7 Empty 66/33MHz. 3.3V Long/Short PCI card\r\n/N0/IB8/P0/B1/C0 Yes 33MHz. 5V Short PCI card\r\n/N0/IB8/P0/B1/C1 Yes 33MHz. 5V Short PCI card\r\n/N0/IB8/P0/B1/C2 Empty 33MHz. 5V Long/Short PCI card\r\n/N0/IB8/P0/B0/C3 Empty 66/33MHz. 3.3V Long/Short PCI card\r\n/N0/IB8/P1/B1/C4 Empty 33MHz. 5V Long/Short PCI card\r\n/N0/IB8/P1/B1/C5 Empty 33MHz. 5V Long/Short PCI card\r\n/N0/IB8/P1/B1/C6 Empty 33MHz. 5V Long/Short PCI card\r\n/N0/IB8/P1/B0/C7 Empty 66/33MHz. 3.3V Long/Short PCI card\r\n\r\n\r\nComponent Cpu Mask Description \r\n--------- -------- ----------- \r\nSB2 - No board power \r\n/N0/SB4/P0 2.2 UltraSPARC-III+, 900MHz, 8M ECache \r\n/N0/SB4/P1 2.2 UltraSPARC-III+, 900MHz, 8M ECache \r\n/N0/SB4/P2 2.2 UltraSPARC-III+, 900MHz, 8M ECache \r\n/N0/SB4/P3 2.2 UltraSPARC-III+, 900MHz, 8M ECache \r\n\r\n\r\nComponent Pwr Grid \r\n--------- --- ---- \r\nSSC0 On No grid \r\nSSC1 - No grid \r\nID0 On No grid \r\nPS0 Off Grid 0 \r\nPS1 On Grid 0 \r\nPS2 - Grid 0 \r\nFT0 - Grid 0 \r\nFT1 On Grid 0 \r\nFT2 On Grid 0 \r\nRP0 On Grid 0 \r\nRP2 On Grid 0 \r\nSB0 - Grid 0 \r\nSB2 Off Grid 0 \r\n/N0/SB4 On Grid 0 \r\n/N0/IB6 On Grid 0 \r\n/N0/IB8 On Grid 0

作者: 山野村夫 时间: 2009-07-28 12:08
检查PS0电源线，然后关了重开

作者: guinanhai 时间: 2009-07-28 13:06
把其它测试过的电源线插在PS0上，但前面板PS0的灯都不亮，这是为什么呢？

作者: 山野村夫 时间: 2009-07-28 13:42
标题: 回复 #4 guinanhai 的帖子
有可能PS0坏了，或者开关坏了\r\n\r\n另外，有时候3个PS接着一个插座上，也会出现这个问题，不知道为什么

欢迎光临 Chinaunix (http://bbs.chinaunix.net/)