标题: 【求助】IBM 小机 270 AS400 [打印本页] 作者: hdy2000 时间: 2006-03-30 00:33 标题: 【求助】IBM 小机 270 AS400 因为搬家，就不能启动了。。自检也通不过。。坛内哪位兄弟熟悉的啊。。帮忙一下。。。\r\n\r\n小弟实在没这方面的经验。。PC服务器倒好判断。。AIX的没出息接触灰过系统自检都通不过。。希望坛子的兄弟。。指点一下。。给个思路。。。有详细介绍的更好作者: orian 时间: 2006-03-30 13:22
看看液晶屏幕的代码，查infocenter，置顶的消息大全帖子理有地址\r\n\r\n根据代码判断错误\r\n\r\n但是你的设备是as/400还是rs/6000 ?作者: hdy2000 时间: 2006-03-30 23:08
AS400\r\n\r\n液晶屏幕的代码B1454607，作者: orian 时间: 2006-03-31 12:45
根据置顶的大全帖子找到infocenter地址：注意，原文是pseries, 由于是400/硬件，改成硬件的地址：\r\nhttp://publib.boulder.ibm.com/infocenter/eserver/v1r3s/index.jsp\r\n\r\n左侧硬件信息中心\r\ncustomer service, support, troubleshooting\r\n右侧reference code list for customers\r\n看到B1xxxxxx Check the following for a specific B1xx reference code. If you do not see your reference code, it might indicate a service processor firmware error, or an IPL load device error. \r\nFor possible IPL load device errors, see Recovering from IPL or system failures.\r\n\r\n继续：recovering from ipl or system failures\r\n\r\nRecovering from IPL or system failures\r\nUse this procedure to help recover from IPL or system failures for i5/OS™.\r\n\r\nVerify the following: \r\nThe device from which you performed the IPL (initial program load) is started. \r\nThe tape and CD are inserted correctly. \r\nThe sign-on user ID and password are correct. \r\nThe system is set to the correct mode (Manual, Normal, Auto, or Secure). \r\nIf this is a timed IPL, the system value for date/time and control panel mode is set correctly. \r\nIf this is a remote IPL, the telephone, modem, control panel mode, and QRMTIPL system value are set up correctly. \r\nPerform the following steps to recover from an IPL or system failures:\r\n\r\nFollow these steps to perform an IPL from the control panel or Operations Console Remote Control panel: \r\nSet the system to the Manual mode. \r\nChoose from the following: \r\nIf the system is turned on, select function 03 and press Enter to start an IPL. \r\nIf the system is shut off, ensure that the control panel is in either Normal or Manual mode and press the power-on button. \r\nChoose from the following options: \r\nIf you see the Sign On display, sign onto the system, and continue with step 3. \r\nIf you do not see the Sign On display, do you have a new reference code? \r\nYes: Record the code and go to the Reference codes list for customers. \r\nNo: Contact your next level of support or your hardware service provider. For details, see Contacting IBM support. \r\nOn the IPL Options display, specify Yes for the following parameters: \r\nDefine or change the system at IPL \r\nClear output queues \r\nClear job queues \r\nClear incomplete job logs \r\nChange the system value for QMCHPOOL to a smaller value. \r\nMake sure the system value for QCTLSBSD has the correct spelling, or assign an alternative controlling subsystem. \r\nChange the system value for QPWRDWNLMT to a larger value. \r\nContinue the IPL process. \r\nIf the same failure occurs, set the system to the Normal mode, and then contact your next level of support or your hardware service provider. \r\nParent topic: IBM i5/OS problem analysis\r\n\r\n所以估计是启动设备有问题，先重新安装看看？