请教:
弄了台4640想学习,安装rhel一切正常,装ux就报这个I/O error
* Installing fileset "Networking.100BT-KRN,r=B.11.31" (15 of 2173).
* Installing fileset "Networking.INTL100-KRN,r=B.11.31" (16 of 2173).
* Installing fileset "Networking.NMS2-KRN,r=B.11.31" (17 of 2173).
* Installing fileset "Networking.PPP2-KRN,r=B.11.31" (18 of 2173).
* Installing fileset "Networking.NW-ENG-A-MAN,r=B.11.31" (19 of 2173).
* Installing fileset "Networking.LAN-PRG,r=B.11.31" (20 of 2173).
* Installing fileset "Networking.NET-RUN-64,r=B.11.31" (21 of 2173).
* Installing fileset "Networking.NET-PRG,r=B.11.31" (22 of 2173).
* Installing fileset "Streams.STREAMS2-RUN,r=B.11.31" (23 of 2173).
* Installing fileset "Streams.STREAMS-RUN,r=B.11.31" (24 of 2173).
* Installing fileset "Streams.STREAMS2-KRN,r=B.11.31" (25 of 2173).
Synchronous Page I/O error occurred while paging to/from disk
device 0x1f000000, 1K block #5296662, 8192 bytes of 8192 bytes not paged, page addr =dead31.e00000013988a000, bflag =40000f, bp = e000000155385380
ERROR: File "/tmp/ign_configure/SD_CDROM/Streams/STREAMS2-KRN.2/usr/conf/mod/clone": I/O error (5). Cannot copy it to file "/usr/conf/mod/clone".
Synchronous Page I/O error occurred while paging to/from disk
device 0x1f000000, 1K block #5296672, 8192 bytes of 8192 bytes not paged, page addr =dead31.e00000013988a000, bflag =40000f, bp = e000000155385380
Synchronous Page I/O error occurred while paging to/from disk
device 0x1f000000, 1K block #5296680, 8192 bytes of 8192 bytes not paged, page addr =dead31.e000000139884000, bflag =40000f, bp = e000000155385c80
ERROR: File "/tmp/ign_configure/SD_CDROM/Streams/STREAMS2-KRN.2/usr/conf/mod/echo": I/O error (5). Cannot copy it to file "/usr/conf/mod/echo".
ERROR: File "/tmp/ign_configure/SD_CDROM/Streams/STREAMS2-KRN.2/usr/conf/mod/ffs": I/O error (5). Cannot copy it to file "/usr/conf/mod/ffs".
ERROR: Failed installing fileset "Streams.STREAMS2-KRN,r=B.11.31". Check the above output for details.
* Installing fileset "Streams.STREAMS2-KRN,r=B.11.31" (25 of 2173).
ERROR: The internal uncompression routine (funzip) detected data corruption in file "/tmp/ign_configure/SD_CDROM/Streams/STREAMS2-KRN.2/usr/conf/mod/clone" while
uncompressing it into file "/usr/conf/mod/clone".
ERROR: File "/tmp/ign_configure/SD_CDROM/Streams/STREAMS2-KRN.2/usr/conf/mod/echo": Error 0 (0). Cannot copy it to file "/usr/conf/mod/echo".
ERROR: Failed installing fileset "Streams.STREAMS2-KRN,r=B.11.31". Check the above output for details.
* Installing fileset "Streams.STREAMS2-KRN,r=B.11.31" (25 of 2173).
ERROR: The internal uncompression routine (funzip) detected data corruption in file "/tmp/ign_configure/SD_CDROM/Streams/STREAMS2-KRN.2/usr/conf/mod/clone" while
uncompressing it into file "/usr/conf/mod/clone".
ERROR: File "/tmp/ign_configure/SD_CDROM/Streams/STREAMS2-KRN.2/usr/conf/mod/echo": Error 0 (0). Cannot copy it to file "/usr/conf/mod/echo".
ERROR: Failed installing fileset "Streams.STREAMS2-KRN,r=B.11.31". Check the above output for details.
* Installing fileset "Streams.STREAMS2-KRN,r=B.11.31" (25 of 2173).
ERROR: The internal uncompression routine (funzip) detected data corruption in file "/tmp/ign_configure/SD_CDROM/Streams/STREAMS2-KRN.2/usr/conf/mod/clone" while
uncompressing it into file "/usr/conf/mod/clone".
ERROR: File "/tmp/ign_configure/SD_CDROM/Streams/STREAMS2-KRN.2/usr/conf/mod/echo": Error 0 (0). Cannot copy it to file "/usr/conf/mod/echo".
ERROR: Failed installing fileset "Streams.STREAMS2-KRN,r=B.11.31". Check the above output for details.
ERROR: The Install Phase has suspended.
ERROR: Aborting the Install Phase.
NOTE: More information may be found in the Software Manager logfile using the command "swm job log -v 000001".
======= 01/01/98 01:38:19 UTC END Software Install failed with 15 errors. (user=root) (jobid=000001)
ERROR: Software load had one or more errors.
======= 01/01/98 01:38:19 UTC The operating system software has not been successfully loaded. The swm install(1M) application was not completed or failed to load
some key files. (exit status was = 1).
1: Change the install server and/or depot information.
2: Retry software load process (non-interactive mode).
3: Retry software load process (interactive mode).
4: Run a shell. 作者: 杨杨得益 时间: 2014-05-22 14:46
Shell> info -b all
SYSTEM INFORMATION
Date/Time: Jan 1, 1998 02:04:52 (19:98:01:01:02:04:52)
Manufacturer: hp
Product Name: server rx4640
Product Number: AB372A
Serial Number: USE*******
UUID: 08E7F463-****
System Bus Frequency: 200 MHz
PROCESSOR MODULE INFORMATION
# of L3 L4 Family/
CPU Logical Cache Cache Model Processor
Module CPUs Speed Size Size (hex.) Rev State
------ ------- -------- ------ ------ ------- --- ------------
0 1 1.5 GHz 6 MB None 1F/01 B1 Active
1 1 1.5 GHz 6 MB None 1F/01 B1 Active
MEMORY INFORMATION
---- DIMM A ----- ---- DIMM B ----- ---- DIMM C ----- ---- DIMM D -----
Press ENTER to continue, 'q' to exit:
DIMM Current DIMM Current DIMM Current DIMM Current
--- ------ ---------- ------ ---------- ------ ---------- ------ ----------
0 2048MB Active 2048MB Active 2048MB Active 2048MB Active
1 ---- ---- ---- ----
2 ---- ---- ---- ----
3 ---- ---- ---- ----
4 ---- ---- ---- ----
5 ---- ---- ---- ----
6 ---- ---- ---- ----
7 ---- ---- ---- ----
Active Memory : 8192 MB
Installed Memory : 8192 MB
I/O INFORMATION
BOOTABLE DEVICES
Order Media Type Path
----- ---------- ---------------------------------------
1 CDROM Acpi(HWP0002,0)/Pci(3|0)/Ata(Primary,Master)/CDROM(Entry0)
Press ENTER to continue, 'q' to exit:
2 HARDDRIVE Acpi(HWP0002,100)/Pci(1|0)/Pci(4|0)/Scsi(Pun0,Lun0)/HD(Part1,SigC5DFA466-8245-11D1-8000-D6217B60E58
3 HARDDRIVE Acpi(HWP0002,100)/Pci(1|0)/Pci(4|0)/Scsi(Pun0,Lun0)/HD(Part3,SigC5DFA4B6-8245-11D1-8000-D6217B60E58
Seg Bus Dev Fnc Vendor Device Slot
# # # # ID ID # Path
--- --- --- --- ------ ------ --- -----------
00 00 01 00 0x103C 0x1290 XX Acpi(HWP0002,0)/Pci(1|0)
00 00 01 01 0x103C 0x1048 XX Acpi(HWP0002,0)/Pci(1|1)
00 00 02 00 0x1033 0x0035 XX Acpi(HWP0002,0)/Pci(2|0)
00 00 02 01 0x1033 0x0035 XX Acpi(HWP0002,0)/Pci(2|1)
00 00 02 02 0x1033 0x00E0 XX Acpi(HWP0002,0)/Pci(2|2)
00 00 03 00 0x1095 0x0649 XX Acpi(HWP0002,0)/Pci(3|0)
00 00 04 00 0x1002 0x5159 XX Acpi(HWP0002,0)/Pci(4|0)
00 20 01 00 0x1014 0x01A7 01 Acpi(HWP0002,100)/Pci(1|0)
00 21 04 00 0x0E11 0x0046 01 Acpi(HWP0002,100)/Pci(1|0)/Pci(4|0)
00 20 02 00 0x8086 0x1079 02 Acpi(HWP0002,100)/Pci(2|0)
00 20 02 01 0x8086 0x1079 02 Acpi(HWP0002,100)/Pci(2|1)
Press ENTER to continue, 'q' to exit:
Fast initialization: Enabled
System Wake-On-LAN: Enabled
BOOT INFORMATION
Monarch CPU:
Current Preferred
Monarch Monarch
CPU CPU
Module/ Module/
Logical Logical Warnings
------- --------- --------
0/0 0/0
AutoBoot: ON - Timeout is : 10 sec
Boottest:
BOOTTEST Settings Default Variable
OS is not speedy boot aware.
Press ENTER to continue, 'q' to exit:
Selftest Setting
--------- --------------
early_cpu Run this test
late_cpu Run this test
platform Run this test
chipset Run this test
io_hw Run this test
mem_init Run this test
mem_test Run this test
LAN Address Information:
LAN Address Path
----------------- ----------------------------------------
*Mac(0012799E3022) Acpi(HWP0002,100)/Pci(2|0)/Mac(0012799E3022)
Mac(0012799E3023) Acpi(HWP0002,100)/Pci(2|1)/Mac(0012799E3023)
FIRMWARE INFORMATION
System Firmware Revision: 4.29 [4750]
PAL_A: 7.31/5.37
PAL_B: 5.72
Press ENTER to continue, 'q' to exit:
EFI Spec: 1.10
EFI Intel Drop: 14.62
EFI Build: 5.48
SAL Spec: 3.01
SAL_A: 2.00
SAL_B: 4.29
POSSE: 0.20
ACPI: 7.00
SMBIOS: 2.3.2a
BMC Revision: 4.06
IPMI: 1.00
Management Processor Revision: E.03.32
Updatable EFI Drivers:
Floating-Point Software Assistance Handler: 00000118
Broadcom Gigabit Ethernet Driver: 0007000A
SCSI Bus Driver: 00000021
SCSI Tape Driver: 00000020
Usb Ohci Driver: 00000033
USB Bus Driver: 00000014
USB Bot Mass Storage Driver: 00000014
Generic USB Mass Storage Driver: 00000015