# Floppy drives
device fdc0 at isa? port IO_FD1 irq 6 drq 2
device fd0 at fdc0 drive 0
#device fd1 at fdc0 drive 1
#
# If you have a Toshiba Libretto with its Y-E Data PCMCIA floppy,
# don't use the above line for fdc0 but the following one:
#device fdc0
# ATA and ATAPI devices
#device ata0 at isa? port IO_WD1 irq 14
#device ata1 at isa? port IO_WD2 irq 15
device ata
device atadisk # ATA disk drives
device atapicd # ATAPI CDROM drives
device atapifd # ATAPI floppy drives
#device atapist # ATAPI tape drives
options ATA_STATIC_ID #Static device numbering
# SCSI Controllers
#device ahb # EISA AHA1742 family
#device ahc # AHA2940 and onboard AIC7xxx devices
#device ahd # AHA39320/29320 and onboard AIC79xx devices
#device amd # AMD 53C974 (Tekram DC-390(T))
#device isp # Qlogic family
#device mpt # LSI-Logic MPT/Fusion
#device ncr # NCR/Symbios Logic
#device sym # NCR/Symbios Logic (newer chipsets)
#options SYM_SETUP_LP_PROBE_MAP=0x40
# Allow ncr to attach legacy NCR devices when
# both sym and ncr are configured
#device adv0 at isa?
#device adw
#device bt0 at isa?
#device aha0 at isa?
#device aic0 at isa?
# atkbdc0 controls both the keyboard and the PS/2 mouse
device atkbdc0 at isa? port IO_KBD
device atkbd0 at atkbdc? irq 1 flags 0x1
device psm0 at atkbdc? irq 12
device vga0 at isa?
options VGA_NO_FONT_LOADING
options VGA_NO_MODE_CHANGE
# splash screen/screen saver
pseudo-device splash
# syscons is the default console driver, resembling an SCO console
device sc0 at isa? flags 0x100
options MAXCONS=4
options SC_NO_CUTPASTE
options SC_NO_FONT_LOADING
#options SC_NO_SYSMOUSE
# Enable this and PCVT_FREEBSD for pcvt vt220 compatible console driver
#device vt0 at isa?
#options XSERVER # support for X server on a vt console
#options FAT_CURSOR # start with block cursor
# If you have a ThinkPAD, uncomment this along with the rest of the PCVT lines
#options PCVT_SCANSET=2 # IBM keyboards are non-std
device agp # support several AGP chipsets
# Floating point support - do not disable.
device npx0 at nexus? port IO_NPX irq 13
# Power management support (see LINT for more options)
device apm0 at nexus? disable flags 0x20 # Advanced Power Management
# PCCARD (PCMCIA) support
#device card
#device pcic0 at isa? irq 0 port 0x3e0 iomem 0xd0000
#device pcic1 at isa? irq 0 port 0x3e2 iomem 0xd4000 disable
# Serial (COM) ports
device sio0 at isa? port IO_COM1 flags 0x10 irq 4
device sio1 at isa? port IO_COM2 irq 3
#device sio2 at isa? disable port IO_COM3 irq 5
#device sio3 at isa? disable port IO_COM4 irq 9
# Parallel port
device ppc0 at isa? irq 7
device ppbus # Parallel port bus (required)
device lpt # Printer
device plip # TCP/IP over parallel
device ppi # Parallel port interface device
#device vpo # Requires scbus and da
# PCI Ethernet NICs that use the common MII bus controller code.
# NOTE: Be sure to keep the 'device miibus' line in order to use these NICs!
device miibus # MII bus support
#device dc # DEC/Intel 21143 and various workalikes
device fxp # Intel EtherExpress PRO/100B (82557, 8255
device pcn # AMD Am79C97x PCI 10/100 NICs
device rl # RealTek 8129/8139
#device sf # Adaptec AIC-6915 (``Starfire'')
#device sis # Silicon Integrated Systems SiS 900/SiS 7016
#device ste # Sundance ST201 (D-Link DFE-550TX)
#device tl # Texas Instruments ThunderLAN
#device tx # SMC EtherPower II (83c170 ``EPIC'')
device vr # VIA Rhine, Rhine II
#device wb # Winbond W89C840F
device xl # 3Com 3c90x (``Boomerang'', ``Cyclone'')
#device bge # Broadcom BCM570x (``Tigon III'')
# ISA Ethernet NICs.
# 'device ed' requires 'device miibus'
device ed0 at isa? disable port 0x280 irq 10 iomem 0xd8000
device ex
device ep
device fe0 at isa? disable port 0x300
# Xircom Ethernet
#device xe
# PRISM I IEEE 802.11b wireless NIC.
#device awi
# WaveLAN/IEEE 802.11 wireless NICs. Note: the WaveLAN/IEEE really
# exists only as a PCMCIA device, so there is no ISA attachment needed
# and resources will always be dynamically assigned by the pccard code.
#device wi
# Aironet 4500/4800 802.11 wireless NICs. Note: the declaration below will
# work for PCMCIA and PCI cards, as well as ISA cards set to ISA PnP
# mode (the factory default). If you set the switches on your ISA
# card for a manually chosen I/O address and IRQ, you must specify
# those parameters here.
#device an
# The probe order of these is presently determined by i386/isa/isa_compat.c.
#device ie0 at isa? disable port 0x300 irq 10 iomem 0xd0000
#device le0 at isa? disable port 0x300 irq 5 iomem 0xd0000
#device lnc0 at isa? disable port 0x280 irq 10 drq 0
#device cs0 at isa? disable port 0x300
#device sn0 at isa? disable port 0x300 irq 10
# Pseudo devices - the number indicates how many units to allocate.
pseudo-device loop # Network loopback
pseudo-device ether # Ethernet support
#pseudo-device sl 1 # Kernel SLIP
pseudo-device ppp 1 # Kernel PPP
pseudo-device tun # Packet tunnel.
pseudo-device pty # Pseudo-ttys (telnet etc)
pseudo-device md # Memory "disks"
pseudo-device gif # IPv6 and IPv4 tunneling
pseudo-device faith 1 # IPv6-to-IPv4 relaying (translation)
