Chinaunix

标题: NFS连不上,晕的 [打印本页]

作者: zs_129 时间: 2006-03-22 08:55
标题: NFS连不上,晕的
A机ip192.168.100.3,B机ip192.168.100.4,在A机NFS共享了一个目录,exports文件里是/usr/local/nshare 192.168.100.4(rw)一句,A机NFS和PORTMAP服务都开了,iptables -F过了,可是B机执行mount -t nfs 192.168.100.3:/usr/local/nshare /mnt/nfsshare就出现mount:RPC:Remote system error - Connection refused,B机上/mnt/nfsshare目录也建了,各位高手指点一下小弟吧!

作者: 我爱钓鱼 时间: 2006-03-22 10:22
B机也要启用portmap.

作者: zs_129 时间: 2006-03-22 11:18
B机portmap也起了啊

[ 本帖最后由 zs_129 于 2006-3-22 11:51 编辑 ]

作者: zs_129 时间: 2006-03-22 16:05
有人说mount:RPC:Remote system error - Connection refused是因为server的portmap没开,但是我确实开了,iptables都已经被我禁掉了

作者: devinbi 时间: 2006-03-22 18:08
标题: 回复 1楼 zs_129 的帖子
showmount -e 192.168.100.3
看看A机输出了文件系统没有，还有相应的权限

作者: zs_129 时间: 2006-03-23 09:07
晕,mount之后出现mount:RPC:progarm not registered是什么概念?

作者: devinbi 时间: 2006-03-23 22:31
标题: 回复 6楼 zs_129 的帖子
RPC服务没有起来

作者: zs_129 时间: 2006-03-24 08:14
A机portmap和nfs都开了,B机portmap也开了,到底是什么原因啊?
rpcinfo查询如下:
[root@Linux root]# rpcinfo -p 192.168.100.2
程序版本协议端口
100000 2 tcp 111  portmapper
100000 2 udp 111  portmapper
100024 1 udp 1024  status
100024 1 tcp 1024  status
391002 2 tcp 1025  sgi_fam
100011 1 udp 990  rquotad
100011 2 udp 990  rquotad
100011 1 tcp 993  rquotad
100011 2 tcp 993  rquotad
100003 2 udp 2049  nfs
100003 3 udp 2049  nfs
100021 1 udp 1026  nlockmgr
100021 3 udp 1026  nlockmgr
100021 4 udp 1026  nlockmgr
100005 1 udp 1027  mountd
100005 1 tcp 1026  mountd
100005 2 udp 1027  mountd
100005 2 tcp 1026  mountd
100005 3 udp 1027  mountd
100005 3 tcp 1026  mountd

都开了啊

[ 本帖最后由 zs_129 于 2006-3-24 08:23 编辑 ]

作者: wikingki 时间: 2006-03-26 18:49
是不是跟selinux有关？

作者: zs_129 时间: 2006-03-27 08:36
redhat linux 9没有selinux

作者: platinum 时间: 2006-03-27 08:39
"iptables -F" != "service iptables stop"
两边都关掉，都起 protmap，能通再说，安全后考虑

作者: zs_129 时间: 2006-03-27 08:47
后来我把两边的iptables都stop了,但是还是不行

作者: platinum 时间: 2006-03-27 08:51
或许是你 NFS 配置有问题，贴出来看看

作者: zs_129 时间: 2006-03-27 09:04
就贴etc/exports文件吗?

作者: zs_129 时间: 2006-03-27 09:16
/usr/local/nshare 192.168.100.4(rw)

作者: zs_129 时间: 2006-03-27 15:01
platinum 帮我看一下呢

作者: platinum 时间: 2006-03-27 15:55
分别贴出两台机器的下列内容
# netstata -lnp
# iptables-save

贴出 NFS 服务器的
# ll /usr/local

贴出你从 client 的 mount 用法，以及提示信息
贴出 NFS server 的 /var/log/messages

作者: zs_129 时间: 2006-03-28 09:20
NFS Server:
[root@Linux log]# netstat -lnp
Active Internet connections (only servers)
Proto Recv-Q Send-Q Local Address          Foreign Address       State    PID/Program name
tcp       0    0 0.0.0.0:1024          0.0.0.0:*             LISTEN    1511/
tcp       0    0 127.0.0.1:1025       0.0.0.0:*             LISTEN    1630/xinetd
tcp       0    0 0.0.0.0:1026          0.0.0.0:*             LISTEN    1663/rpc.mountd
tcp       0    0 0.0.0.0:139          0.0.0.0:*             LISTEN    1795/smbd
tcp       0    0 0.0.0.0:111          0.0.0.0:*             LISTEN    1492/
tcp       0    0 0.0.0.0:6000          0.0.0.0:*             LISTEN    1859/X
tcp       0    0 0.0.0.0:976          0.0.0.0:*             LISTEN    1644/rpc.rquotad
tcp       0    0 0.0.0.0:22             0.0.0.0:*             LISTEN    1615/sshd
tcp       0    0 127.0.0.1:631          0.0.0.0:*             LISTEN    1722/cupsd
tcp       0    0 127.0.0.1:25          0.0.0.0:*             LISTEN    1683/
udp       0    0 0.0.0.0:1024          0.0.0.0:*                         1511/
udp       0    0 0.0.0.0:2049          0.0.0.0:*                         -
udp       0    0 0.0.0.0:1026          0.0.0.0:*                         -
udp       0    0 0.0.0.0:1027          0.0.0.0:*                         1663/rpc.mountd
udp       0    0 192.168.10.122:137    0.0.0.0:*                         1799/nmbd
udp       0    0 192.168.100.2:137    0.0.0.0:*                         1799/nmbd
udp       0    0 0.0.0.0:137          0.0.0.0:*                         1799/nmbd
udp       0    0 192.168.10.122:138    0.0.0.0:*                         1799/nmbd
udp       0    0 192.168.100.2:138    0.0.0.0:*                         1799/nmbd
udp       0    0 0.0.0.0:138          0.0.0.0:*                         1799/nmbd
udp       0    0 0.0.0.0:839          0.0.0.0:*                         1511/
udp       0    0 0.0.0.0:973          0.0.0.0:*                         1644/rpc.rquotad
udp       0    0 0.0.0.0:111          0.0.0.0:*                         1492/
udp       0    0 0.0.0.0:631          0.0.0.0:*                         1722/cupsd
Active UNIX domain sockets (only servers)
Proto RefCnt Flags    Type    State       I-Node PID/Program name Path
unix  2    [ ACC ]    STREAM    LISTENING    2290 1702/gpm          /dev/gpmctl
unix  2    [ ACC ]    STREAM    LISTENING    2517 1831/             /tmp/.gdm_socket
unix  2    [ ACC ]    STREAM    LISTENING    2398 1786/             /tmp/.font-unix/fs7100
unix  2    [ ACC ]    STREAM    LISTENING    2527 1859/X             /tmp/.X11-unix/X0

[root@Linux local]# ll
总用量 48
drwxr-xr-x 2 root    root       4096 2003-01-25  bin
drwxr-xr-x 2 root    root       4096 2003-01-25  etc
drwxr-xr-x 2 root    root       4096 2003-01-25  games
drwxr-xr-x 2 root    root       4096 2003-01-25  include
drwxr-xr-x 2 root    root       4096 2003-01-25  lib
drwxr-xr-x 2 root    root       4096 2003-01-25  libexec
drwxr-xr-x 2 root    root       4096  3月 17 11:18 nshare
drwxr-xr-x 2 root    root       4096  3月  6 15:35 rpm
drwxr-xr-x 2 root    root       4096 2003-01-25  sbin
drwxr-xr-x 4 root    root       4096  2月 16 16:56 share
drwxr-xr-x 5 xxk    sambatest    4096  3月  9 15:07 smbdir
drwxr-xr-x 2 root    root       4096 2003-01-25  src

Client:
[root@localhost root]# netstat -lnp
Active Internet connections (only servers)
Proto Recv-Q Send-Q Local Address          Foreign Address       State    PID/Program name
tcp       0    0 0.0.0.0:1024          0.0.0.0:*             LISTEN    1544/
tcp       0    0 127.0.0.1:1025       0.0.0.0:*             LISTEN    1663/xinetd
tcp       0    0 0.0.0.0:111          0.0.0.0:*             LISTEN    1525/
tcp       0    0 0.0.0.0:22             0.0.0.0:*             LISTEN    1649/sshd
tcp       0    0 127.0.0.1:631          0.0.0.0:*             LISTEN    1722/cupsd
tcp       0    0 127.0.0.1:25          0.0.0.0:*             LISTEN    1683/
udp       0    0 0.0.0.0:1024          0.0.0.0:*                         1544/
udp       0    0 0.0.0.0:872          0.0.0.0:*                         1544/
udp       0    0 0.0.0.0:111          0.0.0.0:*                         1525/
udp       0    0 0.0.0.0:631          0.0.0.0:*                         1722/cupsd
Active UNIX domain sockets (only servers)
Proto RefCnt Flags    Type    State       I-Node PID/Program name Path
unix  2    [ ACC ]    STREAM    LISTENING    2206 1702/gpm          /dev/gpmctl
unix  2    [ ACC ]    STREAM    LISTENING    2301 1779/             /tmp/.font-unix/fs7100

mount方法:mount -t nfs 192.168.100.2:/usr/local/nshare /mnt/nfsshare

作者: zs_129 时间: 2006-03-28 09:21
/var/log/messages:
Mar 27 08:39:45 Linux syslogd 1.4.1: restart.
Mar 27 08:39:45 Linux syslog: syslogd startup succeeded
Mar 27 08:39:45 Linux syslog: klogd startup succeeded
Mar 27 08:39:45 Linux kernel: klogd 1.4.1, log source = /proc/kmsg started.
Mar 27 08:39:45 Linux kernel: Linux version 2.4.20-8 (bhcompile@porky.devel.redhat.com) (gcc version 3.2.2 20030222 (Red Hat Linux 3.2.2-5)) #1 Thu Mar 13 17:54:28 EST 2003
Mar 27 08:39:45 Linux kernel: BIOS-provided physical RAM map:
Mar 27 08:39:45 Linux kernel:  BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
Mar 27 08:39:45 Linux kernel:  BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
Mar 27 08:39:45 Linux kernel:  BIOS-e820: 00000000000ca000 - 00000000000cc000 (reserved)
Mar 27 08:39:45 Linux kernel:  BIOS-e820: 00000000000dc000 - 0000000000100000 (reserved)
Mar 27 08:39:45 Linux kernel:  BIOS-e820: 0000000000100000 - 0000000005ef0000 (usable)
Mar 27 08:39:45 Linux kernel:  BIOS-e820: 0000000005ef0000 - 0000000005efc000 (ACPI data)
Mar 27 08:39:45 Linux kernel:  BIOS-e820: 0000000005efc000 - 0000000005f00000 (ACPI NVS)
Mar 27 08:39:45 Linux kernel:  BIOS-e820: 0000000005f00000 - 0000000006000000 (usable)
Mar 27 08:39:45 Linux kernel:  BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
Mar 27 08:39:45 Linux kernel:  BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
Mar 27 08:39:46 Linux  3月 27 08:39:45 portmap: portmap startup succeeded
Mar 27 08:39:45 Linux kernel:  BIOS-e820: 00000000fffe0000 - 0000000100000000 (reserved)
Mar 27 08:39:45 Linux kernel: 0MB HIGHMEM available.
Mar 27 08:39:45 Linux kernel: 96MB LOWMEM available.
Mar 27 08:39:45 Linux kernel: On node 0 totalpages: 24576
Mar 27 08:39:45 Linux kernel: zone(0): 4096 pages.
Mar 27 08:39:45 Linux rpc.statd[1511]: Version 1.0.1 Starting
Mar 27 08:39:45 Linux nfslock: rpc.statd startup succeeded
Mar 27 08:39:45 Linux rpc.statd[1511]: gethostbyname error for Linux
Mar 27 08:39:45 Linux kernel: zone(1): 20480 pages.
Mar 27 08:39:45 Linux keytable: Loading keymap:
Mar 27 08:39:45 Linux kernel: zone(2): 0 pages.
Mar 27 08:39:46 Linux keytable:
Mar 27 08:39:46 Linux kernel: Kernel command line: ro root=LABEL=/ hdc=ide-scsi
Mar 27 08:39:46 Linux keytable:
Mar 27 08:39:46 Linux kernel: ide_setup: hdc=ide-scsi
Mar 27 08:39:46 Linux rc: Starting keytable:  succeeded
Mar 27 08:39:46 Linux kernel: Initializing CPU#0
Mar 27 08:39:46 Linux kernel: Detected 2940.672 MHz processor.
Mar 27 08:39:46 Linux kernel: Console: colour VGA+ 80x25
Mar 27 08:39:46 Linux kernel: Calibrating delay loop... 5858.91 BogoMIPS
Mar 27 08:39:46 Linux kernel: Memory: 92520k/98304k available (1347k kernel code, 4564k reserved, 999k data, 132k init, 0k highmem)
Mar 27 08:39:46 Linux kernel: Dentry cache hash table entries: 16384 (order: 5, 131072 bytes)
Mar 27 08:39:46 Linux kernel: Inode cache hash table entries: 8192 (order: 4, 65536 bytes)
Mar 27 08:39:46 Linux kernel: Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Mar 27 08:39:46 Linux kernel: Buffer-cache hash table entries: 4096 (order: 2, 16384 bytes)
Mar 27 08:39:46 Linux kernel: Page-cache hash table entries: 32768 (order: 5, 131072 bytes)
Mar 27 08:39:46 Linux kernel: CPU: Trace cache: 12K uops<6>CPU: L2 cache: 1024K
Mar 27 08:39:46 Linux kernel: Intel machine check architecture supported.
Mar 27 08:39:46 Linux random: Initializing random number generator:  succeeded
Mar 27 08:39:46 Linux kernel: Intel machine check reporting enabled on CPU#0.
Mar 27 08:39:46 Linux rc: Starting pcmcia:  succeeded
Mar 27 08:39:46 Linux kernel: CPU: Intel(R) Pentium(R) 4 CPU 2.93GHz stepping 08
Mar 27 08:39:46 Linux kernel: Enabling fast FPU save and restore... done.
Mar 27 08:39:46 Linux kernel: Enabling unmasked SIMD FPU exception support... done.
Mar 27 08:39:46 Linux kernel: Checking 'hlt' instruction... OK.
Mar 27 08:39:46 Linux kernel: POSIX conformance testing by UNIFIX
Mar 27 08:39:46 Linux kernel: mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
Mar 27 08:39:46 Linux kernel: mtrr: detected mtrr type: Intel
Mar 27 08:39:46 Linux kernel: PCI: PCI BIOS revision 2.10 entry at 0xfd9a0, last bus=1
Mar 27 08:39:46 Linux kernel: PCI: Using configuration type 1
Mar 27 08:39:46 Linux kernel: PCI: Probing PCI hardware
Mar 27 08:39:46 Linux kernel: PCI: Using IRQ router PIIX [8086/7110] at 00:07.0
Mar 27 08:39:46 Linux kernel: PCI: Cannot allocate resource region 4 of device 00:07.1
Mar 27 08:39:46 Linux kernel: Limiting direct PCI/PCI transfers.
Mar 27 08:39:46 Linux kernel: isapnp: Scanning for PnP cards...
Mar 27 08:39:46 Linux netfs: Mounting other filesystems:  succeeded
Mar 27 08:39:46 Linux kernel: isapnp: No Plug & Play device found
Mar 27 08:39:46 Linux kernel: Linux NET4.0 for Linux 2.4
Mar 27 08:39:46 Linux kernel: Based upon Swansea University Computer Society NET3.039
Mar 27 08:39:46 Linux apmd[1578]: Version 3.0.2 (APM BIOS 1.2, Linux driver 1.16)
Mar 27 08:39:46 Linux kernel: Initializing RT netlink socket
Mar 27 08:39:46 Linux apmd: apmd startup succeeded
Mar 27 08:39:46 Linux kernel: apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16)
Mar 27 08:39:46 Linux kernel: Starting kswapd
Mar 27 08:39:46 Linux kernel: VFS: Disk quotas vdquot_6.5.1
Mar 27 08:39:46 Linux kernel: pty: 2048 Unix98 ptys configured
Mar 27 08:39:46 Linux kernel: Serial driver version 5.05c (2001-07-0

with MANY_PORTS MULTIPORT SHARE_IRQ SERIAL_PCI ISAPNP enabled
Mar 27 08:39:46 Linux kernel: ttyS0 at 0x03f8 (irq = 4) is a 16550A
Mar 27 08:39:46 Linux autofs: automount startup succeeded
Mar 27 08:39:46 Linux kernel: ttyS1 at 0x02f8 (irq = 3) is a 16550A
Mar 27 08:39:46 Linux kernel: Real Time Clock Driver v1.10e
Mar 27 08:39:46 Linux kernel: Floppy drive(s): fd0 is 1.44M
Mar 27 08:39:46 Linux kernel: FDC 0 is a post-1991 82077
Mar 27 08:39:46 Linux kernel: NET4: Frame Diverter 0.46
Mar 27 08:39:46 Linux kernel: RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
Mar 27 08:39:46 Linux kernel: Uniform Multi-Platform E-IDE driver Revision: 7.00beta-2.4
Mar 27 08:39:46 Linux kernel: ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
Mar 27 08:39:46 Linux kernel: PIIX4: IDE controller at PCI slot 00:07.1
Mar 27 08:39:46 Linux kernel: PIIX4: chipset revision 1
Mar 27 08:39:46 Linux kernel: PIIX4: not 100%% native mode: will probe irqs later
Mar 27 08:39:46 Linux kernel: ide1: BM-DMA at 0x1478-0x147f, BIOS settings: hdc

MA, hdd:pio
Mar 27 08:39:46 Linux kernel: hdc: VMware Virtual IDE CDROM Drive, ATAPI CD/DVD-ROM drive
Mar 27 08:39:46 Linux kernel: ide1 at 0x170-0x177,0x376 on irq 15
Mar 27 08:39:46 Linux kernel: ide-floppy driver 0.99.newide
Mar 27 08:39:46 Linux kernel: ide-floppy driver 0.99.newide
Mar 27 08:39:46 Linux kernel: md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
Mar 27 08:39:46 Linux kernel: md: Autodetecting RAID arrays.
Mar 27 08:39:46 Linux kernel: md: autorun ...
Mar 27 08:39:46 Linux kernel: md: ... autorun DONE.
Mar 27 08:39:46 Linux kernel: NET4: Linux TCP/IP 1.0 for NET4.0
Mar 27 08:39:47 Linux kernel: IP Protocols: ICMP, UDP, TCP, IGMP
Mar 27 08:39:47 Linux kernel: IP: routing cache hash table of 512 buckets, 4Kbytes
Mar 27 08:39:47 Linux kernel: TCP: Hash tables configured (established 8192 bind 16384)
Mar 27 08:39:47 Linux kernel: Linux IP multicast router 0.06 plus PIM-SM
Mar 27 08:39:47 Linux kernel: NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
Mar 27 08:39:47 Linux kernel: RAMDISK: Compressed image found at block 0
Mar 27 08:39:47 Linux kernel: Freeing initrd memory: 248k freed
Mar 27 08:39:47 Linux kernel: VFS: Mounted root (ext2 filesystem).
Mar 27 08:39:47 Linux kernel: SCSI subsystem driver Revision: 1.00
Mar 27 08:39:47 Linux kernel: PCI: Found IRQ 11 for device 00:10.0
Mar 27 08:39:47 Linux kernel: scsi: ***** BusLogic SCSI Driver Version 2.1.15 of 17 August 1998 *****
Mar 27 08:39:47 Linux kernel: scsi: Copyright 1995-1998 by Leonard N. Zubkoff <lnz@dandelion.com>
Mar 27 08:39:47 Linux kernel: scsi0: Configuring BusLogic Model BT-958 PCI Wide Ultra SCSI Host Adapter
Mar 27 08:39:47 Linux sshd:  succeeded
Mar 27 08:39:47 Linux kernel: scsi0: Firmware Version: 5.07B, I/O Address: 0x1440, IRQ Channel: 11/Level
Mar 27 08:39:47 Linux kernel: scsi0: PCI Bus: 0, Device: 16, Address: 0xEC800000, Host Adapter SCSI ID: 7
Mar 27 08:39:47 Linux kernel: scsi0: Parity Checking: Enabled, Extended Translation: Enabled
Mar 27 08:39:42 Linux sysctl: kernel.core_uses_pid = 1
Mar 27 08:39:47 Linux kernel: scsi0: Synchronous Negotiation: Ultra, Wide Negotiation: Enabled
Mar 27 08:39:47 Linux apmd[1578]: Charge: * * * (-1% unknown)
Mar 27 08:39:42 Linux network: Setting network parameters:  succeeded
Mar 27 08:39:47 Linux kernel: scsi0: Disconnect/Reconnect: Enabled, Tagged Queuing: Enabled
Mar 27 08:39:42 Linux network: Bringing up loopback interface:  succeeded
Mar 27 08:39:48 Linux kernel: scsi0: Scatter/Gather Limit: 128 of 8192 segments, Mailboxes: 211
Mar 27 08:39:48 Linux kernel: scsi0: Driver Queue Depth: 211, Host Adapter Queue Depth: 192
Mar 27 08:39:48 Linux kernel: scsi0: Tagged Queue Depth: Automatic, Untagged Queue Depth: 3
Mar 27 08:39:48 Linux kernel: scsi0: Error Recovery Strategy: Default, SCSI Bus Reset: Enabled
Mar 27 08:39:48 Linux kernel: scsi0: *** BusLogic BT-958 Initialized Successfully ***
Mar 27 08:39:48 Linux kernel: scsi0 : BusLogic BT-958
Mar 27 08:39:48 Linux kernel: Vendor: VMware, Model: VMware Virtual S  Rev: 1.0
Mar 27 08:39:48 Linux kernel: Type: Direct-Access                   ANSI SCSI revision: 02
Mar 27 08:39:48 Linux kernel: scsi0: Target 0: Queue Depth 28, Asynchronous
Mar 27 08:39:48 Linux kernel: scsi0: Target 1: Queue Depth 3, Asynchronous
Mar 27 08:39:48 Linux kernel: scsi0: Target 2: Queue Depth 3, Asynchronous
Mar 27 08:39:48 Linux kernel: scsi0: Target 3: Queue Depth 3, Asynchronous
Mar 27 08:39:48 Linux kernel: scsi0: Target 4: Queue Depth 3, Asynchronous
Mar 27 08:39:48 Linux kernel: scsi0: Target 5: Queue Depth 3, Asynchronous
Mar 27 08:39:48 Linux kernel: scsi0: Target 6: Queue Depth 3, Asynchronous
Mar 27 08:39:48 Linux kernel: scsi0: Target 7: Queue Depth 3, Asynchronous
Mar 27 08:39:48 Linux kernel: scsi0: Target 8: Queue Depth 3, Asynchronous
Mar 27 08:39:48 Linux kernel: scsi0: Target 9: Queue Depth 3, Asynchronous
Mar 27 08:39:48 Linux kernel: scsi0: Target 10: Queue Depth 3, Asynchronous
Mar 27 08:39:48 Linux kernel: scsi0: Target 11: Queue Depth 3, Asynchronous
Mar 27 08:39:48 Linux kernel: scsi0: Target 12: Queue Depth 3, Asynchronous
Mar 27 08:39:48 Linux kernel: scsi0: Target 13: Queue Depth 3, Asynchronous
Mar 27 08:39:48 Linux kernel: scsi0: Target 14: Queue Depth 3, Asynchronous
Mar 27 08:39:48 Linux kernel: scsi0: Target 15: Queue Depth 3, Asynchronous
Mar 27 08:39:48 Linux kernel: Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
Mar 27 08:39:48 Linux kernel: SCSI device sda: 16777216 512-byte hdwr sectors (8590 MB)
Mar 27 08:39:48 Linux kernel: Partition check:
Mar 27 08:39:48 Linux kernel:  sda: sda1 sda2 sda3
Mar 27 08:39:48 Linux kernel: Journalled Block Device driver loaded
Mar 27 08:39:48 Linux kernel: EXT3-fs: INFO: recovery required on readonly filesystem.
Mar 27 08:39:48 Linux kernel: EXT3-fs: write access will be enabled during recovery.
Mar 27 08:39:48 Linux kernel: scsi0: Tagged Queuing now active for Target 0
Mar 27 08:39:48 Linux kernel: kjournald starting.  Commit interval 5 seconds
Mar 27 08:39:48 Linux kernel: EXT3-fs: recovery complete.
Mar 27 08:39:48 Linux kernel: EXT3-fs: mounted filesystem with ordered data mode.
Mar 27 08:39:48 Linux kernel: Freeing unused kernel memory: 132k freed
Mar 27 08:39:48 Linux kernel: usb.c: registered new driver usbdevfs
Mar 27 08:39:48 Linux kernel: usb.c: registered new driver hub
Mar 27 08:39:48 Linux kernel: usb-uhci.c: $Revision: 1.275 $ time 17:59:01 Mar 13 2003
Mar 27 08:39:48 Linux kernel: usb-uhci.c: High bandwidth mode enabled
Mar 27 08:39:48 Linux kernel: PCI: Found IRQ 9 for device 00:07.2
Mar 27 08:39:48 Linux kernel: PCI: Sharing IRQ 9 with 00:12.0
Mar 27 08:39:48 Linux kernel: usb-uhci.c: USB UHCI at I/O 0x1060, IRQ 9
Mar 27 08:39:48 Linux kernel: usb-uhci.c: Detected 2 ports
Mar 27 08:39:48 Linux kernel: usb.c: new USB bus registered, assigned bus number 1
Mar 27 08:39:48 Linux kernel: hub.c: USB hub found
Mar 27 08:39:48 Linux kernel: hub.c: 2 ports detected
Mar 27 08:39:48 Linux kernel: usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
Mar 27 08:39:48 Linux kernel: usb.c: registered new driver hiddev
Mar 27 08:39:48 Linux kernel: usb.c: registered new driver hid
Mar 27 08:39:48 Linux kernel: hid-core.c: v1.8.1 Andreas Gal, Vojtech Pavlik <vojtech@suse.cz>
Mar 27 08:39:48 Linux kernel: hid-core.c: USB HID support drivers
Mar 27 08:39:48 Linux kernel: mice: PS/2 mouse device common for all mice
Mar 27 08:39:48 Linux kernel: EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,3), internal journal
Mar 27 08:39:48 Linux kernel: Adding Swap: 803240k swap-space (priority -1)
Mar 27 08:39:48 Linux kernel: kjournald starting.  Commit interval 5 seconds
Mar 27 08:39:48 Linux kernel: EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,1), internal journal
Mar 27 08:39:48 Linux kernel: EXT3-fs: mounted filesystem with ordered data mode.
Mar 27 08:39:48 Linux kernel: scsi1 : SCSI host adapter emulation for IDE ATAPI devices
Mar 27 08:39:48 Linux kernel: Vendor: SONY    Model: CD-RW  CRX320E Rev: NYK5
Mar 27 08:39:48 Linux kernel: Type: CD-ROM                            ANSI SCSI revision: 02
Mar 27 08:39:48 Linux kernel: parport0: PC-style at 0x378 [PCSPP,TRISTATE]
Mar 27 08:39:48 Linux kernel: Attached scsi CD-ROM sr0 at scsi1, channel 0, id 0, lun 0
Mar 27 08:39:48 Linux kernel: sr0: scsi3-mmc drive: 0x/52x writer cd/rw xa/form2 cdda tray
Mar 27 08:39:48 Linux kernel: Uniform CD-ROM driver Revision: 3.12
Mar 27 08:39:48 Linux kernel: ip_tables: (C) 2000-2002 Netfilter core team
Mar 27 08:39:48 Linux kernel: pcnet32.c:v1.27b 01.10.2002 tsbogend@alpha.franken.de
Mar 27 08:39:48 Linux kernel: PCI: Found IRQ 10 for device 00:11.0
Mar 27 08:39:48 Linux kernel: pcnet32: PCnet/PCI II 79C970A at 0x1080, 00 0c 29 97 0f a9 assigned IRQ 10.
Mar 27 08:39:48 Linux kernel: eth0: registered as PCnet/PCI II 79C970A
Mar 27 08:39:48 Linux kernel: pcnet32: 1 cards_found.
Mar 27 08:39:48 Linux kernel: ip_tables: (C) 2000-2002 Netfilter core team
Mar 27 08:39:49 Linux xinetd[1630]: xinetd Version 2.3.10 started with libwrap options compiled in.
Mar 27 08:39:49 Linux xinetd[1630]: Started working: 1 available service
Mar 27 08:39:51 Linux xinetd: xinetd startup succeeded
Mar 27 08:39:51 Linux exportfs[1639]: No 'sync' or 'async' option specified for export "192.168.100.4:/usr/local/nshare". Assuming default behaviour ('sync'). NOTE: this default has changed from previous versions
Mar 27 08:39:51 Linux exportfs: exportfs: No 'sync' or 'async' option specified for export "192.168.100.4:/usr/local/nshare".
Mar 27 08:39:51 Linux exportfs: Assuming default behaviour ('sync').
Mar 27 08:39:51 Linux exportfs: NOTE: this default has changed from previous versions
Mar 27 08:39:51 Linux kernel: Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
Mar 27 08:39:51 Linux nfs: Starting NFS services:  succeeded
Mar 27 08:39:51 Linux nfs: rpc.rquotad startup succeeded
Mar 27 08:39:51 Linux nfs: rpc.nfsd startup succeeded
Mar 27 08:39:51 Linux nfs: rpc.mountd startup succeeded
Mar 27 08:39:52 Linux sendmail: sendmail startup succeeded
Mar 27 08:39:52 Linux sendmail: sm-client startup succeeded
Mar 27 08:39:52 Linux gpm: gpm startup succeeded
Mar 27 08:39:52 Linux crond: crond startup succeeded
Mar 27 08:39:56 Linux kernel: parport0: PC-style at 0x378 [PCSPP,TRISTATE]
Mar 27 08:39:56 Linux kernel: lp0: using parport0 (polling).
Mar 27 08:39:56 Linux kernel: lp0: console ready
Mar 27 08:39:56 Linux modprobe: modprobe: Can't locate module char-major-188
Mar 27 08:39:56 Linux last message repeated 15 times
Mar 27 08:39:56 Linux cups: cupsd startup succeeded
Mar 27 08:39:57 Linux xfs: xfs startup succeeded
Mar 27 08:39:58 Linux xfs: ignoring font path element /usr/X11R6/lib/X11/fonts/cyrillic (unreadable)
Mar 27 08:39:59 Linux smb: smbd startup succeeded
Mar 27 08:39:59 Linux smb: nmbd startup succeeded
Mar 27 08:39:59 Linux anacron: anacron startup succeeded
Mar 27 08:39:59 Linux atd: atd startup succeeded
Mar 27 08:40:05 Linux kernel: mtrr: your processor doesn't support write-combining
Mar 27 08:52:14 Linux sshd(pam_unix)[1870]: session opened for user zhaoshuang by (uid=500)
Mar 27 08:52:18 Linux  3月 27 08:52:18 su(pam_unix)[1900]: session opened for user root by zhaoshuang(uid=500)
Mar 27 09:05:06 Linux portmap[1978]: connect from 192.168.100.4 to dump(): request from unauthorized host
Mar 27 09:05:06 Linux portmap[1979]: connect from 192.168.100.4 to getport(mountd): request from unauthorized host
Mar 27 09:05:06 Linux portmap[1980]: connect from 192.168.100.4 to getport(mountd): request from unauthorized host

作者: zs_129 时间: 2006-03-28 09:25
看起来好象客户端被拒绝的样子

作者: platinum 时间: 2006-03-28 09:50
我要的 iptables-save 的信息呢？
就算没有任何提示也应该告诉我一下
一点一点帮忙分析已经很麻烦了，一点一点去要自己问过的而对方没提供的东西更是让人感觉心烦。。。

对于目前没有 iptables 提示的情况下（默认防火墙不存在），初步怀疑两个地方
1、portmap 的问题，netstat -lnp 竟然看不到是哪个 prog 在跑，我的至少提示 PID/portmap
2、/etc/exports 的问题，不排除里面有全角字符或其他原因，建议修改为 “/path *(rw,sync)” 后再试

作者: zs_129 时间: 2006-03-28 10:45
NFS Server iptables-save没有任何提示
Client [root@localhost mnt]# iptables-save
# Generated by iptables-save v1.2.7a on Tue Mar 28 10:41:03 2006
*filter
:INPUT ACCEPT [827:91582]
:FORWARD ACCEPT [0:0]
:OUTPUT ACCEPT [500:51414]
COMMIT
# Completed on Tue Mar 28 10:41:03 2006
麻烦platinum了,不好意思,我自己再看一下,thanks for your help

作者: platinum 时间: 2006-03-28 11:03

原帖由 zs_129 于 2006-3-28 10:45 发表
NFS Server iptables-save没有任何提示
Client [root@localhost mnt]# iptables-save
# Generated by iptables-save v1.2.7a on Tue Mar 28 10:41:03 2006
*filter
:INPUT ACCEPT [827:91582]
:FORWARD ACCE ...

我问的是 server 和 client 的情况，这次你又只贴了 server 的
为什么不看好我的问题然后一次说清呢？像挤牙膏一样，连我都觉得累了

作者: zs_129 时间: 2006-03-28 13:31
晕,你要的我都贴了啊

作者: zs_129 时间: 2006-03-28 13:36
我没有只贴Server,Client不是也贴了吗?在Server上iptables-save没有任何提示,然后client上iptables-save情况如下:
[root@localhost mnt]# iptables-save
# Generated by iptables-save v1.2.7a on Tue Mar 28 10:41:03 2006
*filter
:INPUT ACCEPT [827:91582]
:FORWARD ACCEPT [0:0]
:OUTPUT ACCEPT [500:51414]
COMMIT
# Completed on Tue Mar 28 10:41:03 2006

我没有贴错啊!!

作者: platinum 时间: 2006-03-28 13:36
sorry，是我没有看仔细
你按照我前面的方法测试一下，修改 NFS 的配置文件，把 IP 改成 * 试试看
我认为问题出在 portmap 上

作者: zs_129 时间: 2006-03-28 13:38
好的,我去试试,如果是portmap的问题的话那要如何修改?是Server还是Client的portmap问题?

作者: zs_129 时间: 2006-03-28 14:02
我试过了,改为/usr/local/nshare *(rw,sync)
还是不可以

作者: phpman 时间: 2006-03-28 16:38
/etc/hosts.allow

这个里边去看吧。

作者: zs_129 时间: 2006-03-29 09:53
hosts.allow里有portmap:192.168.100.4/255.255.255.0:allow,被允许的

作者: jason_zhangwz 时间: 2006-03-29 10:09
redhat的nfs確實有這樣的怪問題,我到現在也不知道是為什麼,我也同樣碰到過.
最後是重新安裝portmap和nfs才解決的.
不知道是什麼導致的.
等待高手解答.

作者: 我爱钓鱼 时间: 2006-03-29 14:53

原帖由 zs_129 于 2006-3-29 09:53 发表
hosts.allow里有portmap:192.168.100.4/255.255.255.0:allow,被允许的

先把/etc/hosts.allow和hosts.deny中的所有语句都注释掉,然后再试试.

作者: zs_129 时间: 2006-03-29 16:45
终于好了,还是hosts.allow和hosts.deny的问题,可是为什么会有问题,hosts.deny里portmap:ALL:deny,hosts.allow里portmap:192.168.100.4/255.255.255.0:allow,hosts.allow的优先级高于hosts.deny,为什么会出现被阻止的情况呢?谢谢jason_zhangwz\我爱钓鱼还有platinum,谢谢大家帮忙

作者: platinum 时间: 2006-03-29 16:53
个人建议使用 iptables 就好了，不要用 /etc/hosts.*

作者: 我爱钓鱼 时间: 2006-03-29 22:15

原帖由 zs_129 于 2006-3-29 16:45 发表
终于好了,还是hosts.allow和hosts.deny的问题,可是为什么会有问题,hosts.deny里portmap:ALL:deny,hosts.allow里portmap:192.168.100.4/255.255.255.0:allow,hosts.allow的优先级高于hosts.deny,为什么会出现被阻止 ...

把hosts.allow中改成protmap:192.168.100.4:allow试试。man hosts.allow的例子中有131.155.72.0/255.255.254.0的写法，不过你的192.168.100.4/255.255.255.0的写法恐怕不正确。

作者: zs_129 时间: 2006-03-31 21:59
OK,那我先试试etc/hosts.*,以后使用的话就学学iptables

作者: initx 时间: 2006-04-05 13:43
提示: 作者被禁止或删除内容自动屏蔽

作者: netmaster110 时间: 2006-04-06 00:56

原帖由 我爱钓鱼 于 2006-3-29 22:15 发表

把hosts.allow中改成protmap:192.168.100.4:allow试试。man hosts.allow的例子中有131.155.72.0/255.255.254.0的写法，不过你的192.168.100.4/255.255.255.0的写法恐怕不正确。

192.168.100.4/255.255.255.0 与192.168.100.4/255.255.255.0有什么区别？？？不就是一个掩码位数的不同，应该不会有什么影响吧？

作者: netmaster110 时间: 2006-04-06 14:22

原帖由 zs_129 于 2006-3-29 16:45 发表
终于好了,还是hosts.allow和hosts.deny的问题,可是为什么会有问题,hosts.deny里portmap:ALL:deny,hosts.allow里portmap:192.168.100.4/255.255.255.0:allow,hosts.allow的优先级高于hosts.deny,为什么会出现被阻止 ...

有没有人能解释一下其中的问题？？？？？？？？？？？？？？？

作者: shijiang1130 时间: 2006-04-07 18:09
标题: 与/etc/host.allow和/etc/host.deny也有关吧
如题

作者: ljt98 时间: 2006-04-10 10:14
cd /usr/nfs/lib/下，
启动nfs相关进程。

作者: fish007 时间: 2006-04-12 10:00
用netstat -an看530端口开了没有

欢迎光临 Chinaunix (http://bbs.chinaunix.net/)