Chinaunix

标题: 熟悉SUN4800服务器的大虾帮我解决故障,万分感谢！ [打印本页]

作者: fjh_74 时间: 2006-07-13 08:41
标题: 熟悉SUN4800服务器的大虾帮我解决故障,万分感谢！
单位的SUN4800机器，可以进系统，但我发现它的/N0/IB8板上的电源灯不亮，下面是我进了SC端口检测的具体报文，谁能告诉我如何处理？/N0/IB8板有专用的电源模块吗？能更换吗？是否更换即可正常？
SF4800-1-SC0:SC> showlogs

Jul 06 11:29:12 SF4800-1-SC0 Platform.SC: [ID 378906 local0.error]
/partition0/RP0/dx0:
>>> Safari Port Error Status 8[0x27] : 0x00048000
         AccScU3IFPar [18:18] : 0x1
            FirstError [15:15] : 0x1

>>> Safari Port Error Status 9[0x28] : 0x00048000
         AccScU3IFPar [18:18] : 0x1
            FirstError [15:15] : 0x1

Jul 06 11:29:12 SF4800-1-SC0 Platform.SC: [ID 542020 local0.error]
/partition0/RP0/dx1:
Safari Port Error Status 8[0x27] : 0x00040000
         AccScU3IFPar [18:18] : 0x1

>>> Safari Port Error Status 9[0x28] : 0x00048000
         AccScU3IFPar [18:18] : 0x1
            FirstError [15:15] : 0x1

Jul 06 11:29:12 SF4800-1-SC0 Platform.SC: [ID 728126 local0.notice] Clock failover enabled.
Jul 06 11:29:13 SF4800-1-SC0 Platform.SC: [ID 816057 local0.error] [AD] Event: SF4800.ASIC.null.null.null
   CSN: 0417AK2044 DomainID: A ADInfo: 1.SCAPP.17.0
   Time: Thu Jul 06 11:29:13 GMT+08:00 2006
   FRU-List-Count: 1; FRU-PN: null; FRU-SN: null; FRU-LOC: null
   Recommended-Action: Service action required

Jul 06 11:29:13 SF4800-1-SC0 Platform.SC: [ID 789080 local0.crit] A fatal condition is detected on Domain A. Initiating automatic restoration for this domain.
Jul 06 11:29:13 SF4800-1-SC0 Platform.SC: [ID 185053 local0.error] Repeater Board Slot 12 DX0 Port 8 : Data parity error on internal datapath. Domain will continue operation.
Jul 06 11:29:13 SF4800-1-SC0 Platform.SC: [ID 620190 local0.notice] A: CycleKeyswitch: Initiating keyswitch: off, domain A.
Jul 06 11:29:25 SF4800-1-SC0 Platform.SC: [ID 285170 local0.error] [AD] Event: SF4800.ASIC.DX.SCH_U3_IN_ERR_OR_IPAR.30223028
   CSN: 0417AK2044 DomainID: ? ADInfo: 1.SCAPP.17.0
   Time: Thu Jul 06 11:29:13 GMT+08:00 2006
   FRU-List-Count: 2; FRU-PN: 5016418; FRU-SN: 012071; FRU-LOC: RP2
                     FRU-PN: null; FRU-SN: null; FRU-LOC: null
   Recommended-Action: Service action required

Jul 06 11:29:25 SF4800-1-SC0 Platform.SC: [ID 201437 local0.error] Repeater Board Slot 12 DX0 Port 9 : Data parity error on internal datapath. Domain will continue operation.
Jul 06 11:29:33 SF4800-1-SC0 Platform.SC: [ID 285686 local0.error] [AD] Event: SF4800.ASIC.DX.SCH_U3_IN_ERR_OR_IPAR.30223029
   CSN: 0417AK2044 DomainID: ? ADInfo: 1.SCAPP.17.0
   Time: Thu Jul 06 11:29:25 GMT+08:00 2006
   FRU-List-Count: 2; FRU-PN: 5016418; FRU-SN: 012071; FRU-LOC: RP2
                     FRU-PN: null; FRU-SN: null; FRU-LOC: null
   Recommended-Action: Service action required

Jul 06 11:29:33 SF4800-1-SC0 Platform.SC: [ID 187101 local0.error] Repeater Board Slot 12 DX1 Port 8 : Data parity error on internal datapath. Domain will continue operation.
Jul 06 11:29:37 SF4800-1-SC0 Platform.SC: [ID 286202 local0.error] [AD] Event: SF4800.ASIC.DX.SCH_U3_IN_ERR_OR_IPAR.31223028
   CSN: 0417AK2044 DomainID: ? ADInfo: 1.SCAPP.17.0
   Time: Thu Jul 06 11:29:33 GMT+08:00 2006
   FRU-List-Count: 2; FRU-PN: 5016418; FRU-SN: 012071; FRU-LOC: RP2
                     FRU-PN: null; FRU-SN: null; FRU-LOC: null
   Recommended-Action: Service action required

Jul 06 11:29:37 SF4800-1-SC0 Platform.SC: [ID 203485 local0.error] Repeater Board Slot 12 DX1 Port 9 : Data parity error on internal datapath. Domain will continue operation.
Jul 06 11:29:42 SF4800-1-SC0 Platform.SC: [ID 286970 local0.error] [AD] Event: SF4800.ASIC.DX.SCH_U3_IN_ERR_OR_IPAR.31223029
   CSN: 0417AK2044 DomainID: ? ADInfo: 1.SCAPP.17.0
   Time: Thu Jul 06 11:29:37 GMT+08:00 2006
   FRU-List-Count: 2; FRU-PN: 5016418; FRU-SN: 012071; FRU-LOC: RP2
                     FRU-PN: null; FRU-SN: null; FRU-LOC: null
   Recommended-Action: Service action required

Jul 06 11:29:57 SF4800-1-SC0 Platform.SC: [ID 299301 local0.notice] A: CycleKeyswitch: Initiating keyswitch: on, domain A.
Jul 06 11:30:11 SF4800-1-SC0 Platform.SC: [ID 367513 local0.warning] Frame Manager connected. ID: 0003ba:4e9bbb
Jul 11 09:59:36 SF4800-1-SC0 Platform.SC: [ID 153495 local0.notice] Domain Reboot A: Initiating keyswitch: on, domain A.

SF4800-1-SC0:SC> showboards

Slot    Pwr Component Type                State    Status    Domain
----    --- --------------                -----    ------    ------
SSC0    On  System Controller             Main    Passed    -
SSC1    On  Present                      Spare    -       -
ID0    On  Sun Fire 4800 Centerplane    -       OK       -
PS0    On  A153 Power Supply             -       OK       -
PS1    On  A153 Power Supply             -       OK       -
PS2    On  A153 Power Supply             -       OK       -
FT0    On  Fan Tray                      Low Speed  OK       -
FT1    On  Fan Tray                      Low Speed  OK       -
FT2    On  Fan Tray                      Low Speed  OK       -
RP0    On  Repeater Board                -       OK       -
RP2    On  Repeater Board                -       OK       -
/N0/SB4  On  CPU Board V2                Active    Passed    A
/N0/IB6  On  PCI I/O Board                Active    Passed    A
/N0/IB8  ? Unknown board                Assigned -       A

SF4800-1-SC0:SC> showplatform

Domain Solaris Nodename Domain Status          Keyswitch
--------  ------------------  -----------------------  -------------
A       EJMAIN1          Active - Solaris       on
B       -                Powered Off             off
C       -                Powered Off             off
D       -                Powered Off             off

The system controller is configured to be on a network.

WARNING: The link is down!

Network settings: static
Hostname: SF4800-1-SC0
IP Address: 192.168.100.10
Netmask: 255.255.255.0
Gateway:
DNS Domain:
Primary DNS Server:
Secondary DNS Server:
Connection type: telnet
Idle connection timeout : No timeout
Loghost for Platform: 192.168.100.15
Log Facility for Platform: local0

SNTP server:

SNMP Agent: disabled
Chassis Description: Sun Fire 4800
Chassis Contact:
Chassis Location:

ACL for Domain A: SB0 SB2 SB4 IB6 IB8
ACL for Domain B:
ACL for Domain C:
ACL for Domain D:

Chassis HostID: 8307bbcc
PROC RTUs installed: 0
PROC Headroom Quantity: 0
PROC RTUs reserved for domain A: 0
PROC RTUs reserved for domain B: 0
PROC RTUs reserved for domain C: 0
PROC RTUs reserved for domain D: 0

SC POST diag Level: min
SC Failover: disabled
Logical Hostname:

Chassis is in single partition mode.

Frame: 0003ba:4e9bbb (Wed Jul 12 16:59:41 GMT+08:00 2006)
      Fail LED:Off Service LED:Off

Frame Fan Trays
               Left Tray Right Tray
   State:          OK          OK
Power LED:          On          On
Fault LED:          Off          Off
Service LED:          Off          Off
   Speed:       Slow       Slow
Temperature:       Normal       Normal
   Power:          OK          OK
   Fan 0:          OK          OK
   Fan 1:          OK          OK
   Fan 2:          OK          OK

Frame RTS
Rear/Left    - OK, Connected to the System
Rear/Right    - OK
Front/Left    - Not Present
Front/Right    - Not Present

SF4800-1-SC0:SC> showcodlicense
Description  Ver Expiration  Count  Status
-----------  --- ----------  -----  ------
SF4800-1-SC0:SC> showcodusage
Resource    In Use  Installed  Licensed  Status
--------    ------  ---------  --------  ------
PROC             0       0       0  OK: 0 available

Domain/Resource  In Use  Installed  Reserved
---------------  ------  ---------  --------
A - PROC             0       0       0
B - PROC             0       0       0
C - PROC             0       0       0
D - PROC             0       0       0
Unused - PROC       0       0       0
SF4800-1-SC0:SC> showcomponent

Component          Status Pending  POST Description
---------          ------ -------  ---- -----------
/N0/SB4/P0       enabled  -       untest empty
/N0/SB4/P1       enabled  -       untest empty
/N0/SB4/P2       enabled  -       pass UltraSPARC-III+, 1200MHz, 8M ECache
/N0/SB4/P3       enabled  -       pass UltraSPARC-III+, 1200MHz, 8M ECache
/N0/SB4/P0/B0/L0 enabled  -       untest empty
/N0/SB4/P0/B0/L2 enabled  -       untest empty
/N0/SB4/P0/B1/L1 enabled  -       untest empty
/N0/SB4/P0/B1/L3 enabled  -       untest empty
/N0/SB4/P1/B0/L0 enabled  -       untest empty
/N0/SB4/P1/B0/L2 enabled  -       untest empty
/N0/SB4/P1/B1/L1 enabled  -       untest empty
/N0/SB4/P1/B1/L3 enabled  -       untest empty
/N0/SB4/P2/B0/L0 enabled  -       pass 1024M DRAM
/N0/SB4/P2/B0/L2 enabled  -       pass 1024M DRAM
/N0/SB4/P2/B1/L1 enabled  -       untest empty
/N0/SB4/P2/B1/L3 enabled  -       untest empty
/N0/SB4/P3/B0/L0 enabled  -       pass 1024M DRAM
/N0/SB4/P3/B0/L2 enabled  -       pass 1024M DRAM
/N0/SB4/P3/B1/L1 enabled  -       untest empty
/N0/SB4/P3/B1/L3 enabled  -       untest empty
/N0/IB6/P0       enabled  -       pass IO Controller 0
/N0/IB6/P1       enabled  -       pass IO Controller 1
/N0/IB6/P0/B0    enabled  -       untest 66/33MHz. PCI Bus
/N0/IB6/P0/B1    enabled  -       untest 33MHz. PCI Bus
/N0/IB6/P1/B0    enabled  -       untest 66/33MHz. PCI Bus
/N0/IB6/P1/B1    enabled  -       untest 33MHz. PCI Bus
/N0/IB6/P0/B1/C0 enabled  -       untest 33MHz. 5V Short PCI card
/N0/IB6/P0/B1/C1 enabled  -       untest 33MHz. 5V Short PCI card
/N0/IB6/P0/B1/C2 enabled  -       untest 33MHz. 5V Long/Short PCI card
/N0/IB6/P0/B0/C3 enabled  -       untest 66/33MHz. 3.3V Long/Short PCI card
/N0/IB6/P1/B1/C4 enabled  -       untest 33MHz. 5V Long/Short PCI card
/N0/IB6/P1/B1/C5 enabled  -       untest 33MHz. 5V Long/Short PCI card
/N0/IB6/P1/B1/C6 enabled  -       untest 33MHz. 5V Long/Short PCI card
/N0/IB6/P1/B0/C7 enabled  -       untest 66/33MHz. 3.3V Long/Short PCI card

SF4800-1-SC0:SC> showenvironment

Slot Device Sensor Value  Units    Age    Status
------- --------- --------- ------ --------- ------- ------
SSC0 SBBC 0 Temp. 0 43    Degrees C 6 sec OK
SSC0 CBH 0    Temp. 0 50    Degrees C 6 sec OK
SSC0 SSC 0    Temp. 0 28    Degrees C 6 sec OK
SSC0 SSC 0    Temp. 1 26    Degrees C 6 sec OK
SSC0 SSC 0    Temp. 2 34    Degrees C 6 sec OK
SSC0 SSC 0    1.5 VDC 0 1.50 Volts DC 6 sec OK
SSC0 SSC 0    3.3 VDC 0 3.35 Volts DC 6 sec OK
SSC0 SSC 0    5 VDC 0 5.01 Volts DC 6 sec OK
PS0    48 VDC 0  Current 0 3.16 Amps       6 sec OK
PS0    48 VDC 0  48 VDC 0  56.33  Volts DC 6 sec OK
PS0    48 VDC 0  Temp. 0 23    Degrees C 6 sec OK
PS0    48 VDC 1  Current 0 0.35 Amps       6 sec OK
PS0    48 VDC 1  48 VDC 0  55.02  Volts DC 6 sec OK
PS1    48 VDC 0  Current 0 3.50 Amps       5 sec OK
PS1    48 VDC 0  48 VDC 0  56.33  Volts DC 5 sec OK
PS1    48 VDC 0  Temp. 0 23    Degrees C 5 sec OK
PS1    48 VDC 1  Current 0 0.37 Amps       5 sec OK
PS1    48 VDC 1  48 VDC 0  55.02  Volts DC 5 sec OK
PS2    48 VDC 0  Current 0 2.79 Amps       5 sec OK
PS2    48 VDC 0  48 VDC 0  56.07  Volts DC 5 sec OK
PS2    48 VDC 0  Temp. 0 30    Degrees C 5 sec OK
PS2    48 VDC 1  Current 0 0.37 Amps       5 sec OK
PS2    48 VDC 1  48 VDC 0  55.02  Volts DC 5 sec OK
FT0    Fan 0    Cooling 0 Low             4 sec OK
FT1    Fan 0    Cooling 0 Low             4 sec OK
FT2    Fan 0    Cooling 0 Low             3 sec OK
RP0    Board 0 1.5 VDC 0 1.50 Volts DC 3 sec OK
RP0    Board 0 3.3 VDC 0 3.27 Volts DC 3 sec OK
RP0    Board 0 Temp. 0 26    Degrees C 3 sec OK
RP0    Board 0 Temp. 1 25    Degrees C 3 sec OK
RP0    SDC 0    Temp. 0 58    Degrees C 3 sec OK
RP0    AR 0    Temp. 0 54    Degrees C 3 sec OK
RP0    DX 0    Temp. 0 49    Degrees C 3 sec OK
RP0    DX 1    Temp. 0 45    Degrees C 3 sec OK
RP2    Board 0 1.5 VDC 0 1.48 Volts DC 3 sec OK
RP2    Board 0 3.3 VDC 0 3.27 Volts DC 3 sec OK
RP2    Board 0 Temp. 0 25    Degrees C 3 sec OK
RP2    Board 0 Temp. 1 24    Degrees C 3 sec OK
RP2    SDC 0    Temp. 0 63    Degrees C 3 sec OK
RP2    AR 0    Temp. 0 58    Degrees C 3 sec OK
RP2    DX 0    Temp. 0 52    Degrees C 3 sec OK
RP2    DX 1    Temp. 0 49    Degrees C 3 sec OK
/N0/SB4 Board 0 1.5 VDC 0 1.50 Volts DC 3 sec OK
/N0/SB4 Board 0 3.3 VDC 0 3.29 Volts DC 3 sec OK
/N0/SB4 SDC 0    Temp. 0 74    Degrees C 3 sec OK
/N0/SB4 AR 0    Temp. 0 51    Degrees C 3 sec OK
/N0/SB4 DX 0    Temp. 0 66    Degrees C 3 sec OK
/N0/SB4 DX 1    Temp. 0 67    Degrees C 3 sec OK
/N0/SB4 DX 2    Temp. 0 67    Degrees C 3 sec OK
/N0/SB4 DX 3    Temp. 0 63    Degrees C 3 sec OK
/N0/SB4 SBBC 0 Temp. 0 59    Degrees C 3 sec OK
/N0/SB4 SBBC 1 Temp. 0 45    Degrees C 3 sec OK
/N0/SB4 Board 1 Temp. 2 29    Degrees C 3 sec OK
/N0/SB4 Board 1 Temp. 3 32    Degrees C 3 sec OK
/N0/SB4 CPU 2    Temp. 0 46    Degrees C 3 sec OK
/N0/SB4 CPU 2    Core 2 1.39 Volts DC 3 sec OK
/N0/SB4 CPU 3    Temp. 0 47    Degrees C 3 sec OK
/N0/SB4 CPU 3    Core 3 1.38 Volts DC 3 sec OK
/N0/IB6 Board 0 1.5 VDC 0 1.51 Volts DC 3 sec OK
/N0/IB6 Board 0 3.3 VDC 0 3.35 Volts DC 3 sec OK
/N0/IB6 Board 0 5 VDC 0 4.95 Volts DC 3 sec OK
/N0/IB6 Board 0 Temp. 0 29    Degrees C 3 sec OK
/N0/IB6 Board 0 Temp. 1 29    Degrees C 3 sec OK
/N0/IB6 Board 0 12 VDC 0  12.11  Volts DC 3 sec OK
/N0/IB6 SDC 0    Temp. 0 63    Degrees C 3 sec OK
/N0/IB6 AR 0    Temp. 0 45    Degrees C 3 sec OK
/N0/IB6 DX 0    Temp. 0 55    Degrees C 3 sec OK
/N0/IB6 DX 1    Temp. 0 52    Degrees C 3 sec OK
/N0/IB6 SBBC 0 Temp. 0 48    Degrees C 3 sec OK
/N0/IB6 IOASIC 0  Temp. 0 57    Degrees C 4 sec OK
/N0/IB6 IOASIC 1  Temp. 1 44    Degrees C 4 sec OK

作者: youngvv 时间: 2006-07-13 09:18
很有可能IB8已坏，RP灯是什么颜色？

POST

作者: henghengxj 时间: 2006-07-13 09:20
电源灯不亮？！没看错吧......

作者: xieliangcheng 时间: 2006-07-13 09:20
1、用螺丝刀打开前门看看前面的电源是否正常,三个电源指示灯是否正常?

2、试着关机重启试试, 看是否有故障灯亮起，故障是否消除?
SC>setkeyswitch -d a off
SC>setkeyswitch on

试着执行SC>poweron /N0/IB8 或 poweron all

注意看起动时是/N0/IB8是否有电源指示灯亮起

3、如果还不行，打SUN 800电话

作者: fjh_74 时间: 2006-07-13 09:30
/N0/IB8板上的最上面一个象闪电图标的灯没亮，我想是电源灯或工作灯。
1、我打开了前面的电源面板，三块电源的工作灯都是好的。而且4800顶部也没亮故障灯，好奇怪！

作者: fjh_74 时间: 2006-07-13 09:31

原帖由 youngvv 于 2006-7-13 09:18 发表
很有可能IB8已坏，RP灯是什么颜色？

POST

RP灯是是哪个？

作者: youngvv 时间: 2006-07-13 09:33
就是Repeater Board,
可以把IB8重新插拔一次看看

作者: zyl555 时间: 2006-07-13 09:37
做一下post就清楚了！
估计IB8坏掉了

作者: henghengxj 时间: 2006-07-13 09:51

原帖由 youngvv 于 2006-7-13 09:33 发表
就是Repeater Board,
可以把IB8重新插拔一次看看

感觉应该先这样试试，但是如果电源灯不亮，估计是不是接触的问题......电源灯都不亮，肯定找不到啊

作者: fjh_74 时间: 2006-07-13 10:54

原帖由 henghengxj 于 2006-7-13 09:51 发表

感觉应该先这样试试，但是如果电源灯不亮，估计是不是接触的问题......电源灯都不亮，肯定找不到啊

哦，谢谢！可以把底下的IB6换过来试吗？

作者: fjh_74 时间: 2006-07-13 10:55

原帖由 zyl555 于 2006-7-13 09:37 发表
做一下post就清楚了！
估计IB8坏掉了

如何做POST？谢谢！

作者: fjh_74 时间: 2006-07-13 11:44

原帖由 zyl555 于 2006-7-13 09:37 发表
做一下post就清楚了！
估计IB8坏掉了

请问post怎么做？

作者: jlh8791951 时间: 2008-10-21 11:48
标题: SUN4800 电源问题
谁能解释一下我的SUN4800 两个电源模块故障。我估计是保护了

请问这样的电源模块能够激活吗？我确信外部UPS电源没有问题。

欢迎光临 Chinaunix (http://bbs.chinaunix.net/)