Chinaunix

标题: 用vmware6.0安装完solaris10进系统找不到网卡---[已解决] [打印本页]

作者: ^日出东方^ 时间: 2007-09-05 10:04
标题: 用vmware6.0安装完solaris10进系统找不到网卡---[已解决]
在安装solaris10时刚开始就能识别到网卡的硬件型号是"pcn0"但是当我装好进桌面时用
# ifconfig -a
lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
只能回环地址,应该是没有安装上网卡驱动,在google没找到解决办法,还请诸位大侠给个方法,谢谢!!!

[ 本帖最后由 ^日出东方^ 于 2007-9-5 11:57 编辑 ]

作者: 风之幻想 时间: 2007-09-05 10:48
看看你的/etc/path_to_inst中有没有你的这个设备.有了.ifconfig plumb然后使用.

作者: ^日出东方^ 时间: 2007-09-05 10:59
回BZ已经看过了没有pcn0这个设备

# more /etc/path_to_inst
#
# Caution! This file contains critical kernel state
#
"/pseudo" 0 "pseudo"
"/options" 0 "options"
"/xsvc" 0 "xsvc"
"/objmgr" 0 "objmgr"
"/scsi_vhci" 0 "scsi_vhci"
"/isa" 0 "isa"
"/isa/i8042@1,60" 0 "i8042"
"/isa/i8042@1,60/keyboard@0" 0 "kb8042"
"/isa/i8042@1,60/mouse@1" 0 "mouse8042"
"/isa/lp@1,378" 0 "ecpp"
"/isa/asy@1,3f8" 0 "asy"
"/isa/asy@1,2f8" 1 "asy"
"/isa/fdc@1,3f0" 0 "fdc"
"/isa/fdc@1,3f0/fd@0,0" 0 "fd"
"/ramdisk" 0 "ramdisk"
"/pci@0,0" 0 "pci"
"/pci@0,0/display@f" 0 "vgatext"
"/pci@0,0/pci8086,7191@1" 0 "pci_pci"
"/pci@0,0/pci-ide@7,1" 0 "pci-ide"
"/pci@0,0/pci-ide@7,1/ide@0" 0 "ata"
"/pci@0,0/pci-ide@7,1/ide@0/cmdk@0,0" 0 "cmdk"
"/pci@0,0/pci-ide@7,1/ide@1" 1 "ata"
"/pci@0,0/pci-ide@7,1/ide@1/sd@0,0" 16 "sd"
"/pci@0,0/pci1000,30@10" 0 "mpt"
"/pci@0,0/pci15ad,790@11" 1 "pci_pci"
"/pci@0,0/pci15ad,790@11/pci1022,2000@0" 0 "vmxnet"
"/pci@0,0/pci15ad,790@11/pci1022,2000@0" 0 "pcn"
"/pci@0,0/pci15ad,790@11/pci1274,1371@1" 0 "audioens"
"/iscsi" 0 "iscsi"
"/agpgart" 0 "agpgart"
#

作者: easybegin 时间: 2007-09-05 11:04
"/pci@0,0/pci15ad,790@11/pci1022,2000@0" 0 "pcn"
这个是什么？？？

作者: ^日出东方^ 时间: 2007-09-05 11:11
谢谢楼上的朋友,我用
# ifcofnig pcn plumb
ifcofnig: not found
# ifconfig pcn plumb
ifconfig: plumb: pcn: no such interface
# ifconfig pcn0 plumb
ifconfig: plumb: pcn0: no such interface
# more  /etc/hostname.pcn0

刚才又在论坛找了下以前贴子无意中看到这位仁兄也一样的情况但是下面有人解决http://bbs2.chinaunix.net/viewthread.php?tid=978718&pid=7309231&page=1&extra=#pid7309231

#ifconfig -a plumb
# ifconfig -a
lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1
      inet 127.0.0.1 netmask ff000000
vmxnet0: flags=1000842<BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 2
      inet 0.0.0.0 netmask 0
      ether 0:c:29:80:9d:26

发现原来网卡确实是装了vmware-tools改成vmxnet0了,郁闷了一整天终于搞定谢谢各位!

[ 本帖最后由 ^日出东方^ 于 2007-9-5 11:12 编辑 ]

作者: 风之幻想 时间: 2007-09-05 11:25

原帖由 ^日出东方^ 于 2007-9-5 11:11 发表
谢谢楼上的朋友,我用
# ifcofnig pcn plumb
ifcofnig: not found
# ifconfig pcn plumb
ifconfig: plumb: pcn: no such interface
# ifconfig pcn0 plumb
ifconfig: plumb: pcn0: no such interface
# m ...

问题解决了就好.呵呵.

作者: andy.liu 时间: 2007-11-09 13:29
标题: 网卡永久保存
怎么不能永久保存
ifconfig -a plumb

found a pcn0 device and then

ifconfig -a
ifconfig pcn0 up
ifconfig pcn0 你要设的IP
这样就可以配置成功，谁找到怎么永久保存。有成功安装过的没？

欢迎光临 Chinaunix (http://bbs.chinaunix.net/)