免费注册 查看新帖 |

Chinaunix

  平台 论坛 博客 文库
最近访问板块 发新帖
楼主: coologin
打印 上一主题 下一主题

[求助] RX8640更换Cell板要注意什么?有业务啊 [复制链接]

论坛徽章:
0
1 [报告]
发表于 2014-01-12 17:27 |显示全部楼层
本帖最后由 woailili9 于 2014-01-12 17:37 编辑

回复 4# lbseraph

请问下 版主  我看四楼的回复     好像是通过FW同步  PDHC的微码

那如果我换CELL板的时候  直接把旧的那个PDHC插到新的CELL板上

是不是就可以不用升级微码了啊?


另外请问下版主  MP里面是不是可以将分区设置为不为开机加电就自动启动的
是的话  因为一台机器  一加电 就三个分区同时起来  很不方便
   

论坛徽章:
0
2 [报告]
发表于 2014-01-12 18:20 |显示全部楼层
回复 8# lbseraph


版主谢谢  

另外有个问题 我在网上看的另外一个更换RP8620的CELL板的文章
上说   升级FW不止要升级PDHC  还要升级SFW,以下是我看他写的步骤:

进入MP,使用DFW查看,SFW和PDHC都需要同步。进入mp.用dfw来同步firmware.首先同步pdhc.选择好cell2的pdhc的号码.比如9,10.然后提示要输入firmware镜象文件的目录,这时候只要写cell0的号码就可以了,比如1,2.
然后就开始刷flash.完成后,要将电源拔掉.再上电,进入mp卡用sysrev看,发现pdhc已经升完.
这时候用rr命令,设置BIB.再将分区启动到BIB.再用dfw命令同步SFW,过程和上面差不多,但是等的时间要长很多.基本上要20分钟.升完之后重启分区.到efi里一看,完事OK.



1请问他用RR重启分区后,设置BIB,BIB是什么啊?
2.将分区启动到BIB是哪一步啊?然后再用DFW的命令不是在MP中的命令么?

论坛徽章:
0
3 [报告]
发表于 2014-01-13 11:17 |显示全部楼层
回复 10# lbseraph

十分感谢


   

论坛徽章:
0
4 [报告]
发表于 2014-01-13 13:44 |显示全部楼层
回复 10# lbseraph

还有请问下版主     在MP里面可以将分区设置为开机加电不自动启动的么?

有的话请问是哪个里面  我查了下MP的常用命令  好像没找到这个啊

论坛徽章:
0
5 [报告]
发表于 2014-01-13 20:29 |显示全部楼层
十分感谢以上两位的热心帮助  谢谢!!!

论坛徽章:
0
6 [报告]
发表于 2014-01-14 09:44 |显示全部楼层
回复 16# lbseraph




    一开始情况(1月12日更换CPU之前)



[mp] MP:VWR (<cr>,<sp>,+,-,?,F,L,J,D,K,R,T,A,C,U,^B) > [mp]  
32267 SFW  0,0,0  2 4b001d3500e008e8 01000000524a5077 MEM_NON_DEST_TEST
32267                                                 10/01/2013 04:32:55
32266 SFW  0,0,0 *3 648015b500e008e6 00ffff0001ffff15 BOOT_CPU_DECONFIG_NO_POWER
32266                                                 10/01/2013 04:32:55
32265 SFW  0,0,0 *3 648015b500e008e4 00ffff0001ffff15 BOOT_CPU_DECONFIG_NO_POWER
32265                                                 10/01/2013 04:32:55
32264 SFW  0,0,0 *3 6480087500e008e2 00ffff0001ffff15 BOOT_CPU_DECONFIG
32264                                                 10/01/2013 04:32:55
32263 SFW  0,0,0 *3 648015b500e008e0 00ffff0001ffff15 BOOT_CPU_DECONFIG_NO_POWER
32263                                                 10/01/2013 04:32:55
32262 SFW  0,0,0 *3 648015b500e008de 00ffff0001ffff15 BOOT_CPU_DECONFIG_NO_POWER
32262                                                 10/01/2013 04:32:55
32261 SFW  0,0,0 *3 6480087500e008dc 00ffff0001ffff15 BOOT_CPU_DECONFIG
32261                                                 10/01/2013 04:32:55
32260 SFW  0,0,0 *3 648015b500e008da 00ffff0001ffff15 BOOT_CPU_DECONFIG_NO_POWER
32260                                                 10/01/2013 04:32:44
32259 SFW  0,0,0 *3 648015b500e008d8 00ffff0001ffff15 BOOT_CPU_DECONFIG_NO_POWER
32259                                                 10/01/2013 04:32:44
32258 SFW  0,0,0 *3 6480087500e008d6 00ffff0001ffff15 BOOT_CPU_DECONFIG
32258                                                 10/01/2013 04:32:44
32257 SFW  0,0,0  2 5680110b00e008d4 0000000000000003 BOOT_INFO_REGARDING_CPU_NUM
32257                                                 10/01/2013 04:32:44



Log Entry 32266:    10/01/2013 04:32:55
Alert level 3:  Warning
Keyword:  BOOT_CPU_DECONFIG_NO_POWER
Firmware is deconfiguring a CPU due to no power to CPU.  The physical location o
Reporting Entity:  System Firmware located in cabinet 0, slot 0, cpu 0
Physical Location:  Processor source detail 0x5 cabinet 0 cell 0
0x648015b500e008e6 0x00ffff0001ffff15
0x6b0015b500e008e7 0x01000000524a5077








[mp] MP:VWR (<cr>,<sp>,+,-,?,F,L,J,D,K,R,T,A,C,U,^B) > [mp]  
Log Entry 32265:    10/01/2013 04:32:55
Alert level 3:  Warning
Keyword:  BOOT_CPU_DECONFIG_NO_POWER
Firmware is deconfiguring a CPU due to no power to CPU.  The physical location o
Reporting Entity:  System Firmware located in cabinet 0, slot 0, cpu 0
Physical Location:  Processor source detail 0x5 cabinet 0 cell 0
0x648015b500e008e4 0x00ffff0001ffff15
0x6b0015b500e008e5 0x01000000524a5077



[mp] MP:CM> ps

Display detailed status of the selected MP bus device.


The following MP bus devices were found:
+---+----+-----+-------+-------+-----------+
|   |    |     |       |       |           |
|   |    | Sys |       |  IO   | Bulk Pwr  |
|Cab| MP |Bkpln| Cells |Chassis| Supplies  |
| # |M  S|     |0 1 2 3| 0   1 |0 1 2 3 4 5|
+---+----+-----+-------+-------+-----------+
| 0 |*  *|  *  |* * * *| *   * |* * * * * *|
| 8 |*  *|  *  |- - - -| *   * |* * - - - -|
+---+----+-----+-------+-------+-----------+

You may display detailed power and hardware status for the following items:

    T - Cabinet
    S - System Backplane
    G - MP (Core I/O)
    P - IO Chassis
    C - Cell
        Select Device: g

HW status for MP : No Fault Detected

Complex model string: 9000/800/rp8440

MP is not failed over

Cabinet LED is Green

Battery state is good

Last MP software reset occurred WED FEB 01 00:40:33 2051

MP firmware rev B.002.005.012 built on Aug 23 2007 14:34:46

[mp] MP:CM>
[mp] MP:CM> ps

Display detailed status of the selected MP bus device.


The following MP bus devices were found:
+---+----+-----+-------+-------+-----------+
|   |    |     |       |       |           |
|   |    | Sys |       |  IO   | Bulk Pwr  |
|Cab| MP |Bkpln| Cells |Chassis| Supplies  |
| # |M  S|     |0 1 2 3| 0   1 |0 1 2 3 4 5|
+---+----+-----+-------+-------+-----------+
| 0 |*  *|  *  |* * * *| *   * |* * * * * *|
| 8 |*  *|  *  |- - - -| *   * |* * - - - -|
+---+----+-----+-------+-------+-----------+

You may display detailed power and hardware status for the following items:

    T - Cabinet
    S - System Backplane
    G - MP (Core I/O)
    P - IO Chassis
    C - Cell
        Select Device: t

    Enter cabinet number (0 or :

    ... Not a valid cabinet number for this device ...


    Enter cabinet number (0 or : 0

HW status for rp8440 cabinet : NO FAILURE DETECTED

Master/Slave failover is Enabled
Power switch is on
Right Door is closed
Top Door is closed
Left Door is closed

Total Power Available 6000 VA
Total Power Needed 3527 VA
Power Redundancy : redundant
Power Viability : viable


Power Status
---------------+-----+-------+-------+-----------+
               |     |       |       |           |
               | Sys |       |  IO   | Bulk Pwr  |
               |Bkpln| Cells |Chassis| Supplies  |
               |     |0 1 2 3| 0   1 |0 1 2 3 4 5|
---------------+-----+-------+-------+-----------+
Populated     |  *  |* * * *| *   * |* * * * * *|
Enabled       |  *  |* * * *| *   * |* * * * * *|
Power OK      |  *  |* * * *| *   * |* * * * * *|
Warning/Fault |     |       |       |           |
Attention LED |     |       |       |           |


AC Line status:
  Line A0 NOT PRESENT
  Line B0 Present
  Line A1 Present
  Line B1 NOT PRESENT

               -- Press <CR> to continue, or 'Q' to Quit --

Front Fan Speed   : normal
Rear Fan speed    : normal
I/O Bay Fan Speed : normal
Temperature state : normal
Main Fan Redundancy   : redundant
I/O Fan Redundancy    : redundant
Overtemp Shutdown Enabled


            |     BPS     |     PCI     |
            |     Fans    |     Fans    |
            | 0 1 2 3 4 5 | 0 1 2 3 4 5 |
+-----------+-------------+-------------+
  Populated | * * * * * * | * * * * * * |
  Failing   |             |             |
  Failed    |             |             |

            |              Standby/Main Fans            |
            |                     1 1 1 1 1 1 1 1 1 1 2 |
            | 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 |
+-----------+-------------------------------------------+
  Populated | * * * * * * * * * * * * * * * * * * * * * |
  Failing   |                                           |
  Failed    |                                           |

            |  Cell Fans |
            |   CPU    C |
            | 0 1 2 3  C |
+-----------+------------+
Cell 0     |            |
  Populated | * * *    * |
  Failing   |            |
  Failed    |            |
Cell 1     |            |
  Populated | * * *    * |
  Failing   |            |
  Failed    |            |
Cell 2     |            |
  Populated | * * * *  * |
  Failing   |            |
  Failed    |            |
Cell 3     |            |
  Populated | * * * *  * |
  Failing   |            |
  Failed    |            |

[mp] MP:CM>
[mp] MP:CM> ps

Display detailed status of the selected MP bus device.


The following MP bus devices were found:
+---+----+-----+-------+-------+-----------+
|   |    |     |       |       |           |
|   |    | Sys |       |  IO   | Bulk Pwr  |
|Cab| MP |Bkpln| Cells |Chassis| Supplies  |
| # |M  S|     |0 1 2 3| 0   1 |0 1 2 3 4 5|
+---+----+-----+-------+-------+-----------+
| 0 |*  *|  *  |* * * *| *   * |* * * * * *|
| 8 |*  *|  *  |- - - -| *   * |* * - - - -|
+---+----+-----+-------+-------+-----------+

You may display detailed power and hardware status for the following items:

    T - Cabinet
    S - System Backplane
    G - MP (Core I/O)
    P - IO Chassis
    C - Cell
        Select Device: c
    Enter cell number: 0

HW status for Cell 0 : NO FAILURE DETECTED

Power status : on, no fault
Faults above are latched. They are cleared just before the cell is powered on.
Boot is not blocked
PDH memory is shared
Processor Compatibility : OK
RIO cable status : connected
RIO cable connection physical location : PCI Domain 0
Core cell is cell 0
Attention Led is off

PDHC status Leds :  ***-

CPU Module Slot    0 1 2 3
Populated         P P P  
Local 48V Good    * * *  
Power Enabled     *   *  
Power Good        *   *  
   (* - True, P - Processor, T - Terminator)

|       DIMM Presence       |
|                           |
|   Side: |    A   |    B   |
|Echelon: |01234567|01234567|
+---------+--------+--------+
|         |***      ***     |
                                    1 1 1 1 1 1
VRM's           0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5
Present      : * * * * * * * * * * * * * * * *
Enabled      : * * * * * * * * * * * * * * * *
Pwr Good     : * * * * * * * * * * * * * * * *

Front Side Bus Freq.    : 267 MHz
CPU Core Freq.          : 1068 MHz
CPU Part Number         : PA8900

System Boot Rom (SFW) firmware rev 043.006.000
PDH controller (PDHC) firmware rev B.023.003.038 built WED APR 18 21:43:36 2007









1月12日更换CPU第一步骤:将新申请的CPU更换上CPU1。然后新更换上去的CPU不认。

HW status for Cell 0 : FAILURE DETECTED

Power status : on, no fault
Faults above are latched. They are cleared just before the cell is powered on.
Boot is blocked
PDH memory is not shared
Processor Compatibility : FAULT
RIO cable status : connected
RIO cable connection physical location : PCI Domain 0
Core cell is INVALID
Attention Led is off

PDHC status Leds :  --*-

CPU Module Slot    0 1 2 3
Populated         P P P  
Local 48V Good    *   *  
Power Enabled     *   *  
Power Good        *   *  
   (* - True, P - Processor, T - Terminator)

|       DIMM Presence       |
|                           |
|   Side: |    A   |    B   |
|Echelon: |01234567|01234567|
+---------+--------+--------+
|         |***      ***     |
                                    1 1 1 1 1 1
VRM's           0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5
Present      : * * * * * * * * * * * * * * * *
Enabled      : * * * * * * * * * * * * * * * *
Pwr Good     : * * * * * * * * * * * * * * * *

Front Side Bus Freq.    : 267 MHz
CPU Core Freq.          : 1068 MHz
CPU Part Number         : PA8900

System Boot Rom (SFW) firmware rev 043.006.000
PDH controller (PDHC) firmware rev B.023.003.038 built WED APR 18 21:43:36 2007







第二步骤:将新更换上去的1号CPU和2号CPU调换位置后:
[mp] MP:CM> ps

Display detailed status of the selected MP bus device.


The following MP bus devices were found:
+---+----+-----+-------+-------+-----------+
|   |    |     |       |       |           |
|   |    | Sys |       |  IO   | Bulk Pwr  |
|Cab| MP |Bkpln| Cells |Chassis| Supplies  |
| # |M  S|     |0 1 2 3| 0   1 |0 1 2 3 4 5|
+---+----+-----+-------+-------+-----------+
| 0 |*  *|  *  |* * * *| *   * |* * * * * *|
| 8 |*  *|  *  |- - - -| *   * |* * - - - -|
+---+----+-----+-------+-------+-----------+

You may display detailed power and hardware status for the following items:

    T - Cabinet
    S - System Backplane
    G - MP (Core I/O)
    P - IO Chassis
    C - Cell
        Select Device: c
    Enter cell number: 0

HW status for Cell 0 : FAILURE DETECTED

Power status : on, no fault
Faults above are latched. They are cleared just before the cell is powered on.
Boot is blocked
PDH memory is not shared
Processor Compatibility : FAULT
RIO cable status : connected
RIO cable connection physical location : PCI Domain 0
Core cell is INVALID
Attention Led is off

PDHC status Leds :  --*-

CPU Module Slot    0 1 2 3
Populated         P P P  
Local 48V Good    * * *  
Power Enabled     * * *  
Power Good        * * *  
   (* - True, P - Processor, T - Terminator)

|       DIMM Presence       |
|                           |
|   Side: |    A   |    B   |
|Echelon: |01234567|01234567|
+---------+--------+--------+
|         |***      ***     |
                                    1 1 1 1 1 1
VRM's           0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5
Present      : * * * * * * * * * * * * * * * *
Enabled      : * * * * * * * * * * * * * * * *
Pwr Good     : * * * * * * * * * * * * * * * *

Front Side Bus Freq.    : 267 MHz
CPU Core Freq.          : 1068 MHz
CPU Part Number         : PA8900

System Boot Rom (SFW) firmware rev 043.006.000
PDH controller (PDHC) firmware rev B.023.003.038 built WED APR 18 21:43:36 2007


[mp] MP:CM>
[mp] MP:CM> ps

Display detailed status of the selected MP bus device.


The following MP bus devices were found:
+---+----+-----+-------+-------+-----------+
|   |    |     |       |       |           |
|   |    | Sys |       |  IO   | Bulk Pwr  |
|Cab| MP |Bkpln| Cells |Chassis| Supplies  |
| # |M  S|     |0 1 2 3| 0   1 |0 1 2 3 4 5|
+---+----+-----+-------+-------+-----------+
| 0 |*  *|  *  |* * * *| *   * |* * * * * *|
| 8 |*  *|  *  |- - - -| *   * |* * - - - -|
+---+----+-----+-------+-------+-----------+

You may display detailed power and hardware status for the following items:

    T - Cabinet
    S - System Backplane
    G - MP (Core I/O)
    P - IO Chassis
    C - Cell
        Select Device: c
    Enter cell number: 1

HW status for Cell 1 : FAILURE DETECTED

Power status : on, no fault
Faults above are latched. They are cleared just before the cell is powered on.
Boot is blocked
PDH memory is shared
Processor Compatibility : OK
RIO cable status : connected
RIO cable connection physical location : PCI Domain 1
Core cell is INVALID
Attention Led is off

PDHC status Leds :  -***

CPU Module Slot    0 1 2 3
Populated         P P P  
Local 48V Good    * * *  
Power Enabled     * * *  
Power Good        * * *  
   (* - True, P - Processor, T - Terminator)

|       DIMM Presence       |
|                           |
|   Side: |    A   |    B   |
|Echelon: |01234567|01234567|
+---------+--------+--------+
|         |***      ***     |
                                    1 1 1 1 1 1
VRM's           0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5
Present      : * * * * * * * * * * * * * * * *
Enabled      : * * * * * * * * * * * * * * * *
Pwr Good     : * * * * * * * * * * * * * * * *

Front Side Bus Freq.    : 267 MHz
CPU Core Freq.          : 1068 MHz
CPU Part Number         : PA8900

System Boot Rom (SFW) firmware rev 043.006.000
PDH controller (PDHC) firmware rev B.023.003.038 built WED APR 18 21:43:36 2007


         U: Unfiltered
[mp] MP:VWR (<cr>,<sp>,+,-,?,F,L,J,D,K,R,T,A,C,U,^B) > [mp]  
32609 SFW  0,1,0  2 4b001d3510e00b83 0100000052d16831 MEM_NON_DEST_TEST
32609                                                 01/11/2014 15:50:09
32608 SFW  0,1,0  2 4380149b10e00b81 0000000000000003 BOOT_RESET_HCELL_TYPE
32608                                                 01/11/2014 15:49:32
32607 SFW  0,1,0  2 4380149a10e00b7f 00000782ff81cbc8 BOOT_RESET_HCELL_CALLER
32607                                                 01/11/2014 15:49:32
32606 SFW  0,1,0 *3 7780126310e00b7d 0000000000000000 BOOT_FIND_CORE_CELL_CONFIG_SELECT_ERR
32606                                                 01/11/2014 15:49:32
32605 SFW  0,1,0 *3 63800a5510e00b7b 0000000000000002 BOOT_PD_RENDEZ_TIMEOUT
32605                                                 01/11/2014 15:49:27
32604 SFW  0,2,0  2 4b001d3520e00b7a 0100000052d1655b MEM_NON_DEST_TEST
32604                                                 01/11/2014 15:38:03
32603 SFW  0,3,0  2 4b001d3530e00b79 0100000052d1655b MEM_NON_DEST_TEST
32603                                                 01/11/2014 15:38:03
32602 SFW  0,1,0  2 4b001d3510e00b78 0100000052d1654f MEM_NON_DEST_TEST
32602                                                 01/11/2014 15:37:51
32601 PDHC 0,3    2 4480198703e00b76 00ffff03ff04ff12 CC_FAN_OK
32601                                                 01/11/2014 15:37:33
32600 PDHC 0,2    2 4480198702e00b74 00ffff02ff04ff12 CC_FAN_OK
32600                                                 01/11/2014 15:37:31
32599 PDHC 0,1    2 4480198701e00b72 00ffff01ff04ff12 CC_FAN_OK
32599                                                 01/11/2014 15:37:29



32591 PDHC 0,0   *7 f680112400e00b62 0000000000000008 PDHC_CELL_INCOMPATIBLE
32591                                                 01/11/2014 15:37:10
32590 MP   0      2 44800ee700e00b60 00ffffffff01ff68 CELL_ON
32590                                                 01/11/2014 15:37:09
32589 MP   0      2 44800ee700e00b5e 00ffffffff00ff68 CELL_ON
32589                                                 01/11/2014 15:37:08
32588 MP   0      2 44801cf200e00b5c 0000ffffffffff43 IOBP_PWR_REDUNDANT
32588                                                 01/11/2014 15:37:07


32587 MP   0      2 448019da00e00b5a 000000ffffffff69 IOBP_ON
32587                                                 01/11/2014 15:37:07
32586 MP   0      2 44801cf200e00b58 0000ffffffffff43 IOBP_PWR_REDUNDANT
32586                                                 01/11/2014 15:37:07
32585 MP   0      2 448019da00e00b56 000001ffffffff69 IOBP_ON
32585                                                 01/11/2014 15:37:07
32584 CLU  0      2 4480194800e00b54 00ffffffff00ff60 SYS_BKP_CLK_HSO2RCS_GOOD
32584                                                 01/11/2014 15:37:07
32583 CLU  0      2 4480194800e00b52 00ffffffff01ff60 SYS_BKP_CLK_HSO2RCS_GOOD
32583                                                 01/11/2014 15:37:07
32582 MP   0      2 448019d800e00b50 000000ffffffff69 MAIN_BP_ON
32582                                                 01/11/2014 15:37:07
32581 MP   8      2 44801cf208e00b4e 0800ffffffffff43 IOBP_PWR_REDUNDANT
32581                                                 01/11/2014 15:36:57
32580 MP   8      2 448019da08e00b4c 080000ffffffff69 IOBP_ON
32580                                                 01/11/2014 15:36:57
32579 MP   8      2 44801cf208e00b4a 0800ffffffffff43 IOBP_PWR_REDUNDANT
32579                                                 01/11/2014 15:36:57
32578 MP   8      2 448019da08e00b48 080001ffffffff69 IOBP_ON
32578                                                 01/11/2014 15:36:57
32577 MP   8      2 448019d808e00b46 080000ffffffff69 MAIN_BP_ON
32577                                                 01/11/2014 15:36:57

[mp] MP:VWR (<cr>,<sp>,+,-,?,F,L,J,D,K,R,T,A,C,U,^B) > [mp]  
32576 PDHC 0,3    2 448013c303e00b44 00ffff03ffffff94 CELL_EJECTORS_LATCHED
32576                                                 01/11/2014 15:35:08
32575 PDHC 0,2    2 448013c302e00b42 00ffff02ffffff94 CELL_EJECTORS_LATCHED
32575                                                 01/11/2014 15:35:07
32574 PDHC 0,1    2 448013c301e00b40 00ffff01ffffff94 CELL_EJECTORS_LATCHED
32574                                                 01/11/2014 15:35:06
32573 PDHC 0,0   *7 f680112400e00b3e 0000000000000008 PDHC_CELL_INCOMPATIBLE
32573                                                 01/11/2014 15:35:05
32572 PDHC 0,0    2 448013c300e00b3c 00ffff00ffffff94 CELL_EJECTORS_LATCHED
32572                                                 01/11/2014 15:35:05
32571 PDHC 0,3    2 568019d303e00b3a 0000000000000000 PDHC_INFO
32571                                                 01/11/2014 15:35:05
32570 PDHC 0,3    2 568019d303e00b38 003c73b8002513f0 PDHC_INFO
32570                                                 01/11/2014 15:35:05
32569 PDHC 0,3    2 568019d303e00b36 0000020b00000005 PDHC_INFO
32569                                                 01/11/2014 15:35:05
32568 PDHC 0,3    2 568019d303e00b34 003c71a800261544 PDHC_INFO
32568                                                 01/11/2014 15:35:05
32567 PDHC 0,3    2 568019d303e00b32 000000b700000005 PDHC_INFO
32567                                                 01/11/2014 15:35:05
32566 PDHC 0,3    2 568019d303e00b30 003ca32400249548 PDHC_INFO
32566                                                 01/11/2014 15:35:05




    MP MAIN MENU:

         CO: Consoles
        VFP: Virtual Front Panel
         CM: Command Menu
         CL: Console Logs
         SL: Show Event Logs
         FW: Firmware Update
         HE: Help
          X: Exit Connection

[mp] MP> co

    Partitions available:

     #   Name
    ---  ----
     0)  Partition 0 - UX
     1)  Partition 1 - UX
     2)  Partition 2 - UX
     Q)  Quit

    Please select partition number: 0


        Connecting to OS Console: Partition 0 - UX

          (Use <Ctrl-b> to return to main menu.)


- - - - - - - - - - Prior Console Output - - - - - - - - - -

             1A   0xffffc0f4000  Cpu configured, not flagged to be deconfigured
             1B   0xffffc0f5000  Cpu configured, not flagged to be deconfigured
             2A   0xffffc0f8000  Cpu configured, not flagged to be deconfigured
             2B   0xffffc0f9000  Cpu configured, not flagged to be deconfigured




这种情况是不是CPU没换好呢?硬件没换好?







论坛徽章:
0
7 [报告]
发表于 2014-01-14 18:20 |显示全部楼层
回复 20# lbseraph



不是 CELL板应该没问题吧  因为那个CELL板上  3颗物理CPU
0 1 2号  最后0号是没问题的
但是1号和2号CPU  已经被deconfig了

   
您需要登录后才可以回帖 登录 | 注册

本版积分规则 发表回复

  

北京盛拓优讯信息技术有限公司. 版权所有 京ICP备16024965号-6 北京市公安局海淀分局网监中心备案编号:11010802020122 niuxiaotong@pcpop.com 17352615567
未成年举报专区
中国互联网协会会员  联系我们:huangweiwei@itpub.net
感谢所有关心和支持过ChinaUnix的朋友们 转载本站内容请注明原作者名及出处

清除 Cookies - ChinaUnix - Archiver - WAP - TOP