免费注册 查看新帖 |

Chinaunix

  平台 论坛 博客 文库
123下一页
最近访问板块 发新帖
查看: 16852 | 回复: 25
打印 上一主题 下一主题

在PC上装Cisco PIX OS[转贴] [复制链接]

论坛徽章:
0
跳转到指定楼层
1 [收藏(0)] [报告]
发表于 2004-09-17 20:03 |只看该作者 |正序浏览
PIX启动是考FLOOPY把IMAGE读到RAM里去的
Rebooting....

如果把里面的82559网卡拿出那么他会检测不到硬件而不段REBOOT

Cisco Secure PIX Firewall BIOS (3.6)

Booting Floppy

..................................
PIX floppy loader (3.0) #0: Mon Oct 2 07:02:43 PDT 2000
Reading installation media.............

PIX floppy loader (3.0) #0: Mon Oct 2 07:02:43 PDT 2000
Reading installation media.....................................
PIX admin loader (3.0) #0: Mon Oct 2 07:02:44 PDT 2000
Flash=i28F640J5
Flash version 4.4.7, Install version 4.4.7
Do you want me to install new version onto flash? [n] No
loading from flash...

128MB RAM
Flash=i28F640J5 @ 0x300
mcwa i82559 Ethernet at irq 11 MAC: 0002.b308.a0c6
mcwa i82559 Ethernet at irq 10 MAC: 0002.b326.1a09

pixfirewall# show int eth0
interface ethernet0 "outside" is up, line protocol is down
Hardware is “”“i82559”“”“ ethernet, address is 0002.b308.a0c6
IP address 127.0.0.1, subnet mask 255.255.255.255
MTU 1500 bytes, BW 10000 Kbit half duplex
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 packets output, 0 bytes, 0 underruns
0 unicast rpf drops
0 output errors, 0 collisions, 0 interface resets
0 babbles, 0 late collisions, 0 deferred
0 lost carrier, 0 no carrier
pixfirewall#


ISA上的那快东西确定是FLASH无疑了
现在只要按照以下方法就可以把X86变成标标准准的一台PIX520了
下载rawrite.exe,pix529.bin,bh529.bin

C:\>;rawrite
RaWrite 1.2 - Write disk file to raw floppy diskette
Enter source file name: bh59.bin
Enter destination drive: a:
Please insert a formatted diskette into drive A: and press -ENTER- :
Number of sectors per track for this disk is 18.
Writing image to drive A:. Press ^C to abort.
Track: 11 Head: 1 Sector: 16
Done.
C:\>;0

然后就可以利用floopy进入monitor模式下

monitor>; interface 1
0: i8255X @ PCI(bus:0 dev:14 irq:10)
1: i8255X @ PCI(bus:0 dev:13 irq:11)

Using 1: i82557 @ PCI(bus:0 dev:13 irq:11), MAC: 0002.b945.a23c
monitor>; address 172.18.124.154
address 172.18.124.154
monitor>; server 172.18.125.3
server 172.18.125.3
monitor>; file pix611.bin
file pix611.bin
monitor>; ping 172.18.125.3
Sending 5, 100-byte 0xcde2 ICMP Echoes to 172.18.125.3, timeout is 4 seconds:
!!!!!
Success rate is 100 percent (5/5)
monitor>; tftp
tftp pix611.bin@172.18.125.3..........................................
Received 2562048 bytes

Cisco Secure PIX Firewall admin loader (3.0) #0: Tue Dec 517:35:46 PST 2000
System Flash=E28F128J3 @ 0xfff00000
BIOS Flash=am29f400b @ 0xd8000
Flash version 6.1.1, Install version 6.1.1
Do you wish to copy the install image into flash? [n] y

Installing to flash

Serial Number: 480380761 (0x1ca20759)
Activation Key: 760754d0 39f62229 a4a0245f b5b87e80

Do you want to enter a new activation key? [n] n
Writing 2469944 bytes image into flash...

然后A:启动
.................

Firewall>;enable
Firewall#
Firewall#

注意几点
1)安装的时候和OLIVE没区别,显示器上没进度条
2)安装的时候要有ISA或PCI接口的FLASH卡,最好是INTEL的
3)安装的时候PCI上要有2块82550系列的网卡

Good luck


关键是那个flash卡究竟长的什么样子??
PCI CF卡不知是否可以

论坛徽章:
0
26 [报告]
发表于 2010-03-13 10:46 |只看该作者
LZ 能不能不买卡就能装的方法啊 ??

论坛徽章:
0
25 [报告]
发表于 2008-03-14 14:58 |只看该作者
强人!

论坛徽章:
0
24 [报告]
发表于 2005-01-26 14:05 |只看该作者

在PC上装Cisco PIX OS[转贴]

好象要那块卡才行啊,否则都没用

论坛徽章:
0
23 [报告]
发表于 2005-01-25 17:02 |只看该作者

在PC上装Cisco PIX OS[转贴]

网上有卖的。 300大元。
不过不一定能用的。是6000系列用的。

论坛徽章:
0
22 [报告]
发表于 2005-01-19 13:38 |只看该作者

在PC上装Cisco PIX OS[转贴]

原帖由 "wheel" 发表:
可以用硬盘的。。。分出个 64M的HDA1,改grub
加到grub.conf理 map (hd0,0)/cqs.img (fd0) chainloader (hd0,0)/xxx.img rootnoverify (fd0) boot

nod,pix应该也是用flash模拟IDE设备的。
rom不是放在flash上的,flash上面是pix os。
rom是单独的芯片。

论坛徽章:
1
荣誉版主
日期:2011-11-23 16:44:17
21 [报告]
发表于 2005-01-19 10:52 |只看该作者

在PC上装Cisco PIX OS[转贴]

学习一下

论坛徽章:
0
20 [报告]
发表于 2004-10-15 15:18 |只看该作者

在PC上装Cisco PIX OS[转贴]

是啊。。。要分3个主分区
1---winxp
2----64M
3---linux

论坛徽章:
0
19 [报告]
发表于 2004-10-09 04:08 |只看该作者

在PC上装Cisco PIX OS[转贴]

原帖由 "wheel" 发表:
可以用硬盘的。。。分出个 64M的HDA1,改grub
加到grub.conf理 map (hd0,0)/cqs.img (fd0) chainloader (hd0,0)/xxx.img rootnoverify (fd0) boot


Wheel 先生,

可否详细解释怎样安装 PIX到硬盘. 我也想学习PIX. 我是否需要安装 linux 到硬盘先。

谢谢

SeaTigerIII

论坛徽章:
0
18 [报告]
发表于 2004-10-08 11:36 |只看该作者

在PC上装Cisco PIX OS[转贴]

可以用硬盘的。。。分出个 64M的HDA1,改grub
加到grub.conf理 map (hd0,0)/cqs.img (fd0) chainloader (hd0,0)/xxx.img rootnoverify (fd0) boot
  

北京盛拓优讯信息技术有限公司. 版权所有 京ICP备16024965号-6 北京市公安局海淀分局网监中心备案编号:11010802020122 niuxiaotong@pcpop.com 17352615567
未成年举报专区
中国互联网协会会员  联系我们:huangweiwei@itpub.net
感谢所有关心和支持过ChinaUnix的朋友们 转载本站内容请注明原作者名及出处

清除 Cookies - ChinaUnix - Archiver - WAP - TOP