- 论坛徽章:
- 0
|
熟悉COMPAQ MA8000的大虾们帮个忙!
下面是我安装的一些步骤: 可以参考一下\r\nhsg>;clear cli\r\nhsg>;set multibus copy=this\r\nhsg>;set this mirrored_cache\r\nhsg>;set this port_1_topology=fabric\r\nhsg>;set this port_2_topology=fabric\r\nhsg>;set oth port_1_topology=fabric\r\nhsg>;set oth port_2_topology=fabric\r\nhsg>;show connect\r\nhsg>;run config\r\nhsg>;add raidset r0 diskxxxxx (raid 5)\r\nhsg>;add mirrorset m0 diskxxxxx (raid 1)\r\nhsg>;add stripeset s0 diskxxxxx (raid 0)\r\nhsg>;add spareset diskxxxxx (hot spare)\r\n\r\nhsg>;SET FAILEDSET AUTOSPARE\r\n\r\nhsg>;show r0 (m0,s0)\r\nhsg>;init r0 (m0,s0)\r\nhsg>;create_partition r0 size=xx (xx=xx%_ac)\r\nhsg>;create_partition r0 size=xx (xx=xx%)\r\nhsg>;create_partition r0 SIZE=LARGEST\r\nhsg>;add unit d0 r0 partition=1\r\nhsg>;add unit d0 r0 partition=2\r\nhsg>;set d0 disable_access= (all)\r\nhsg>;set d1 enable_access_path= \r\nhsg>;SET D1 DISABLE_ACCESS_PATH=ALL\r\nhsg>;set d1 enable_access_path=MTN1B2\r\nhsg>;SET D101 ENABLE_ACCESS_PATH=(WILLOW1A1,WILLOW2B2)\r\nHSG>; SET D1 ENABLE_ACCESS_PATH=(!NEWCON01,!NEWCON02,!NEWCON03,!NEWCON04)\r\nHSG>; SET D0 ENABLE_ACCESS_PATH=(!NEWCON00,!NEWCON05,!NEWCON06,!NEWCON0\r\nHST>; SET D6 ENABLE_ACCESS_PATH=(85008-04,85008-03,85008-02,85008-01,85004-04,85004-03 ,85004-02,85004-01)\r\n\r\nset d10 enable_access_path=(5801-1,5801-2,5801-3,5801-4,5802-1,5802-2,5802-3,5802-4)\r\nSET FAILEDSET AUTOSPARESET FAILEDSET AUTOSPARE\r\n\r\n\r\nhsg>; show faildset\r\nhsg>;delete faildset \r\n\r\n\r\nhsg>;run frutil (change battery)\r\n\r\nraid 10 \r\n\r\nhsg>;add mirrorset mirr1 diskxxxxx diskxxxxx\r\nhsg>;add mirrorset mirr2 diskxxxxx diskxxxxx\r\nhsg>;add mirrorset mirr3 diskxxxxx diskxxxxx\r\nhsg>;add stripeset stripe1 mirr1 mirr2 mirr3\r\nhsg>;init stripe1\r\nhsg>;show stripe1\r\nhsg>;add \r\n\r\n\r\n\r\nhsg>;set !newcon01 operating_system winntse\r\nhsg>;show this_controller full\r\n\r\n\r\n\r\ncopy single disk unit or mirrorset unit \r\nhsg>;run clone\r\n\r\n\r\n\r\n\r\nclear all config\r\nhsg>;clear oth/thi invalid_catche destroy_unflushed_data\r\n\r\n\r\n\r\nlist all connect\r\nhsg>;show connect\r\n\r\n\r\nlist all unit\r\nhsg>;show units\r\n\r\n\r\n\r\nerase all config \r\nhsg>;configuration reset\r\n\r\n\r\n\r\n\r\nadd raidset raid0 disk10000 disk10100 disk10200 disk10300 disk10400 disk10500 disk10800 disk20000 disk20100 disk20200 disk20300 disk20400 disk20500 |
|