- 论坛徽章:
- 0
|
现有一台HMC控制台,型号是7315-c03,os版本是v3.2.4,主板F/w是2AKT31AUS
现在需要用它去管理P5的服务器,需要将OS升级到v4.X以上,高版本的recover-cd请到以下地址下载:
ftp://ftp.software.ibm.com/software/server/hmc/recover-cd
,里面是最新v4.5的recover-cd,一共7张盘,大约2.6GB
同时if you are upgrading to HMC V3 R3.0 or greater on your HMC, or to HMC V4. R1.0 or greater
HMC's models 7315-C03 and 7310-C03 must be upgraded F/W主板微码
首先你需要确认当前的主板F/w是否需要升级
To determine if you need to update your HMC's BIOS, you must reboot the HMC and verify the "Flash EEPROM Revision Level".
- Reboot the HMC
- When "Press F1 for System Setup" is displayed in the lower left corner of ther screen, press function key "F1".
- When the "IBM Setup Utility" screen is displayed, select the "Main"tab.
- Verify the "Flash EEPROM Revision Level". It will be of the form:
2AKTxxyUS
If BOTH conditions listed below are met, NO update is required.
1.) "xx" is 38 or greater 2.) "y" is a "R"
Otherwise, the BIOS must updated using the following procedure,我的机器微码是2AKT31AUS,按上所述需要升级
7315-c03的最新微码到以下地址下载
[color="#5c81a7"]ftp://techsupport.services.ibm.com/eserver/pseries/hmc/fixes/73xxB38f.exe
给微码做成启动盘
************************************************************************* * * Diskette Creation Instructions * * * The following procedure uses "73xxB38f.exe" to create a diskette. * * If the diskette is built, proceed to "Installation Instructions". * * * Steps... * * * 1. Copy the file "73xxB38f.exe" to free DASD space on a Winxx PC. * * * 2. Insure a blank, formatted 1.44MB diskette in the PC's reader. * * * 3. Execute (Run) "73xxb38f.exe" and follow the instructions. * *
*************************************************************************
开始升级微码
************************************************************************* * * Installation Instructions * * * Steps... * * * 1. Insure the AC power source is secure. Do not power off at any * * during this process. * * * 2. Put the flash update diskette in the drive and power up the * * system.. . * * * 3. Locate the Machine Type & Model information label on the lower * * right had corner of the PC. Note the machine Type and Model, * * (7310-C03 or 7315-C03). * * * 4. From the "PC DOS 7.0 Startup Menu" select ONE of the first two * * options: * * * 1. Load Custom BIOS Lvl 38 and set MTM to 7310C03. * * 2. Load Custom BIOS Lvl 38 and set MTM to 7315C03. * * * 5. If the following flashing window displays: * * * +-------------------------------------+ * | | * * | Administrator Password is invalid | * * | System is ReBooting | * | | * * +-------------------------------------+ * * * The BIOS update diskette does not support this HMC. * * * - Remove the diskette * * - Power off the HMC * * - Insure the HMC is a 7310-C03 or 7315-C03 * * * 6. Update may take up to 2 minutes. Do not power off or restart the * * system during this procedure! Leave the diskette in the computer. * * * 7. A good completion results in a green status screen momentarily * * displayed played stating: "... successfully completed". Do not * * remove the diskette. The PC will reboot. * * * An error condition exists if an Error Code is displayed. Record * * the code for service reference. * * * 8. If during reboot, the following message is displayed: * * * "System Configuration Data updated * * ERROR * * 0162: Configuration Error, default configuration used" * * * Press 'F2' (resume) * * * 9. From the "PC DOS 7.0 Startup Menu" select the last option: * * * 3. Load pSeries System Setup Configuration Data * * * 10. As the process completes, the system will reboot and return to * * "PC DOS 7.0 Startup Menu" * * * 11. The update is now complete. Remove the diskette first and then * * key (press and hold) 'Ctrl Alt Delete' to reboot the system. * * * End of procedure * * *
*************************************************************************
开始升级HMC操作系统
重启HMC,插入v4.5的recover-cd,HMC默认启动顺序是光驱-软驱-硬盘
出现窗口时,安装提示选择F8-安装或更新
选择F1-install/recover
开始recover,大概需要30分钟的时间,第一张盘recover完毕会重起HMC,再提示你插入后面的盘add software,我总共用到了5张盘.
成功之后机器重起,进入HMC界面,选择help-abaut HMC,显示版本v4R5,一切ok.
设置内置网卡en0为dhcp,以及dhcp范围(例9.6.24.1-9.6.24.255,en0即自动设为9.6.24.1,尽量范围小一点),en0连交换机,P5服务器HMC1端口连交换机,p5服务器关机断电,网线用普通直连线即可
设置好后HMC还需要重起一下以使网卡配置生效
P5服务器通电(之前不要将p5服务器通电,否则无法获得dhcp地址),自检完毕后,在HMC上执行server manager-add受管系统-指定IP搜索范围,一般dhcp会从后面地址开始,所以我一般设为9.6.24.250-9.6.24.254,搜索完毕再刷新一下即可在HMC中看到主机.
完成!
本文来自ChinaUnix博客,如果查看原文请点:http://blog.chinaunix.net/u/6617/showart_33929.html |
|