- 论坛徽章:
- 0
|
NFS挂载正常，启动busybox ok，把测试OK的文件夹压制成jffs2文件系统，烧录到flash中，启动GG
求好心人帮忙分析分析！
挂载NFS msg
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
Booting Linux on physical CPU 0x0
Linux version 3.10.46 (panda@panda-K43SD) (gcc version 4.5.1 (ctng-1.8.1-FA) ) #
35 PREEMPT Sat May 14 02:45:47 CST 2016
CPU: ARMv7 Processor [412fc082] revision 2 (ARMv7), cr=10c53c7d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine: SMDKV210
Memory policy: ECC disabled, Data cache writeback
CPU S5PV210/S5PC110 (id 0x43110220)
S3C24XX Clocks, Copyright 2004 Simtec Electronics
S5PV210: PLL settings, A=1000000000, M=667000000, E=96000000 V=54000000
S5PV210: ARMCLK=1000000000, HCLKM=200000000, HCLKD=166750000
HCLKP=133400000, PCLKM=100000000, PCLKD=83375000, PCLKP=66700000
sclk_dmc: source is sclk_a2m (0), rate is 200000000
sclk_onenand: source is hclk_psys (0), rate is 66700000
sclk_fimc: source is ext_xtal (0), rate is 24000000
sclk_fimc: source is ext_xtal (0), rate is 24000000
sclk_fimc: source is ext_xtal (0), rate is 24000000
sclk_cam0: source is ext_xtal (0), rate is 24000000
sclk_cam1: source is ext_xtal (0), rate is 24000000
sclk_fimd: source is ext_xtal (0), rate is 24000000
sclk_mfc: source is sclk_a2m (0), rate is 200000000
sclk_g2d: source is sclk_a2m (0), rate is 200000000
sclk_g3d: source is sclk_a2m (0), rate is 200000000
sclk_csis: source is ext_xtal (0), rate is 24000000
sclk_pwi: source is ext_xtal (0), rate is 24000000
sclk_pwm: source is ext_xtal (0), rate is 24000000
CPU: All CPU(s) started in SVC mode.
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048
Kernel command line: root=/dev/nfs rw nfsroot=192.168.1.101:/home/work/rootfs ip
=192.168.1.120:192.168.1.121:192.168.1.122::eht0: ff console=ttySAC0,115200 ini
t=/linuxrc
PID hash table entries: 2048 (order: 1, 8192 bytes)
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 512MB = 512MB total
Memory: 515548k/515548k available, 8740k reserved, 0K highmem
Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
vmalloc : 0xa0800000 - 0xff000000 (1512 MB)
lowmem : 0x80000000 - 0xa0000000 ( 512 MB)
modules : 0x7f000000 - 0x80000000 ( 16 MB)
.text : 0x80008000 - 0x8037851c (3522 kB)
.init : 0x80379000 - 0x8039b6fc ( 138 kB)
.data : 0x8039c000 - 0x803d19c0 ( 215 kB)
.bss : 0x803d19c0 - 0x8040d468 ( 239 kB)
SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Preemptible hierarchical RCU implementation.
NR_IRQS:208
VIC @f6000000: id 0x00041192, vendor 0x41
VIC @f6010000: id 0x00041192, vendor 0x41
VIC @f6020000: id 0x00041192, vendor 0x41
VIC @f6030000: id 0x00041192, vendor 0x41
sched_clock: 32 bits at 33MHz, resolution 29ns, wraps every 128784ms
Console: colour dummy device 80x30
Calibrating delay loop... 663.55 BogoMIPS (lpj=1658880)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
Setting up static identity map for 0x80299008 - 0x80299060
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations
S3C Power Management, Copyright 2004 Simtec Electronics
S5PV210: Initializing architecture
bio: create slab <bio-0> at 0
SCSI subsystem initialized
Switching to clocksource samsung_clocksource_timer
NET: Registered protocol family 2
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 4, 81920 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP: reno registered
UDP hash table entries: 256 (order: 1, 12288 bytes)
UDP-Lite hash table entries: 256 (order: 1, 12288 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
jffs2: version 2.2. (NAND) �© 2001-2006 Red Hat, Inc.
ROMFS MTD (C) 2007 Red Hat, Inc.
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
dma-pl330 dma-pl330.0: Loaded driver for PL330 DMAC-267056
dma-pl330 dma-pl330.0: DBUFF-8x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32
dma-pl330 dma-pl330.1: Loaded driver for PL330 DMAC-267056
dma-pl330 dma-pl330.1: DBUFF-8x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
s5pv210-uart.0: ttySAC0 at MMIO 0xe2900000 (irq = 74) is a S3C6400/10
console [ttySAC0] enabled
s5pv210-uart.1: ttySAC1 at MMIO 0xe2900400 (irq = 75) is a S3C6400/10
s5pv210-uart.2: ttySAC2 at MMIO 0xe2900800 (irq = 76) is a S3C6400/10
s5pv210-uart.3: ttySAC3 at MMIO 0xe2900c00 (irq = 77) is a S3C6400/10
brd: module loaded
loop: module loaded
s3c24xx-nand s5pv210-nand: Tacls=2, 14ns Twrph0=2 14ns, Twrph1=1 7ns
s3c24xx-nand s5pv210-nand: NAND ECC disabled
NAND device: Manufacturer ID: 0xec, Chip ID: 0xdc (Samsung NAND 512MiB 3,3V 8-bi
t), 512MiB, page size: 2048, OOB size: 64
NAND_ECC_NONE selected by board driver. This is not recommended!
Scanning device for bad blocks
Creating 5 MTD partitions on "NAND":
0x000000000000-0x000000800000 : "bootloader"
0x000000800000-0x000000820000 : "params"
0x000000820000-0x000000a20000 : "log"
0x000000a20000-0x000000d20000 : "kernel"
0x000000d20000-0x000020000000 : "rootfs"
dm9000 dm9000: read wrong id 0x01010101
eth0: dm9000a at a08a8000,a08aa004 IRQ 39 MAC: 00:09:c0:ff:ec:48 (platform data)
mousedev: PS/2 mouse device common for all mice
TCP: cubic registered
NET: Registered protocol family 17
VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 2
dm9000 dm9000 eth0: link down
dm9000 dm9000 eth0: link down
dm9000 dm9000 eth0: link up, 100Mbps, full-duplex, lpa 0xCDE1
IP-Config: Guessing netmask 255.255.255.0
IP-Config: Complete:
device=eth0, hwaddr=00:09:c0:ff:ec:48, ipaddr=192.168.1.120, mask=255.255.2
55.0, gw=192.168.1.122
host=eht0, domain=, nis-domain=(none)
bootserver=192.168.1.121, rootserver=192.168.1.101, rootpath=
VFS: Mounted root (nfs filesystem) on device 0:9.
Freeing unused kernel memory: 136K (80379000 - 8039b000)
init started: BusyBox v1.21.1 (2016-05-02 16:24:55 CST)
Segmentation fault
Please press Enter to activate this console.
Processing /etc/profile...
Done
[root@S5PV210]# ls
bin etc lib mnt root sys usr
dev jffs2 linuxrc proc sbin tmp var
jffs2 fail msg：
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
Booting Linux on physical CPU 0x0
Linux version 3.10.46 (panda@panda-K43SD) (gcc version 4.5.1 (ctng-1.8.1-FA) ) #
35 PREEMPT Sat May 14 02:45:47 CST 2016
CPU: ARMv7 Processor [412fc082] revision 2 (ARMv7), cr=10c53c7d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine: SMDKV210
Memory policy: ECC disabled, Data cache writeback
CPU S5PV210/S5PC110 (id 0x43110220)
S3C24XX Clocks, Copyright 2004 Simtec Electronics
S5PV210: PLL settings, A=1000000000, M=667000000, E=96000000 V=54000000
S5PV210: ARMCLK=1000000000, HCLKM=200000000, HCLKD=166750000
HCLKP=133400000, PCLKM=100000000, PCLKD=83375000, PCLKP=66700000
sclk_dmc: source is sclk_a2m (0), rate is 200000000
sclk_onenand: source is hclk_psys (0), rate is 66700000
sclk_fimc: source is ext_xtal (0), rate is 24000000
sclk_fimc: source is ext_xtal (0), rate is 24000000
sclk_fimc: source is ext_xtal (0), rate is 24000000
sclk_cam0: source is ext_xtal (0), rate is 24000000
sclk_cam1: source is ext_xtal (0), rate is 24000000
sclk_fimd: source is ext_xtal (0), rate is 24000000
sclk_mfc: source is sclk_a2m (0), rate is 200000000
sclk_g2d: source is sclk_a2m (0), rate is 200000000
sclk_g3d: source is sclk_a2m (0), rate is 200000000
sclk_csis: source is ext_xtal (0), rate is 24000000
sclk_pwi: source is ext_xtal (0), rate is 24000000
sclk_pwm: source is ext_xtal (0), rate is 24000000
CPU: All CPU(s) started in SVC mode.
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048
Kernel command line: root=/dev/mtdblock4 rootfstype=jffs2 console=ttySAC0,115200
rw
PID hash table entries: 2048 (order: 1, 8192 bytes)
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 512MB = 512MB total
Memory: 515548k/515548k available, 8740k reserved, 0K highmem
Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
vmalloc : 0xa0800000 - 0xff000000 (1512 MB)
lowmem : 0x80000000 - 0xa0000000 ( 512 MB)
modules : 0x7f000000 - 0x80000000 ( 16 MB)
.text : 0x80008000 - 0x8037851c (3522 kB)
.init : 0x80379000 - 0x8039b6fc ( 138 kB)
.data : 0x8039c000 - 0x803d19c0 ( 215 kB)
.bss : 0x803d19c0 - 0x8040d468 ( 239 kB)
SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Preemptible hierarchical RCU implementation.
NR_IRQS:208
VIC @f6000000: id 0x00041192, vendor 0x41
VIC @f6010000: id 0x00041192, vendor 0x41
VIC @f6020000: id 0x00041192, vendor 0x41
VIC @f6030000: id 0x00041192, vendor 0x41
sched_clock: 32 bits at 33MHz, resolution 29ns, wraps every 128784ms
Console: colour dummy device 80x30
Calibrating delay loop... 663.55 BogoMIPS (lpj=1658880)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
Setting up static identity map for 0x80299008 - 0x80299060
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations
S3C Power Management, Copyright 2004 Simtec Electronics
S5PV210: Initializing architecture
bio: create slab <bio-0> at 0
SCSI subsystem initialized
Switching to clocksource samsung_clocksource_timer
NET: Registered protocol family 2
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 4, 81920 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP: reno registered
UDP hash table entries: 256 (order: 1, 12288 bytes)
UDP-Lite hash table entries: 256 (order: 1, 12288 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
jffs2: version 2.2. (NAND) �© 2001-2006 Red Hat, Inc.
ROMFS MTD (C) 2007 Red Hat, Inc.
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
dma-pl330 dma-pl330.0: Loaded driver for PL330 DMAC-267056
dma-pl330 dma-pl330.0: DBUFF-8x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32
dma-pl330 dma-pl330.1: Loaded driver for PL330 DMAC-267056
dma-pl330 dma-pl330.1: DBUFF-8x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
s5pv210-uart.0: ttySAC0 at MMIO 0xe2900000 (irq = 74) is a S3C6400/10
console [ttySAC0] enabled
s5pv210-uart.1: ttySAC1 at MMIO 0xe2900400 (irq = 75) is a S3C6400/10
s5pv210-uart.2: ttySAC2 at MMIO 0xe2900800 (irq = 76) is a S3C6400/10
s5pv210-uart.3: ttySAC3 at MMIO 0xe2900c00 (irq = 77) is a S3C6400/10
brd: module loaded
loop: module loaded
s3c24xx-nand s5pv210-nand: Tacls=2, 14ns Twrph0=2 14ns, Twrph1=1 7ns
s3c24xx-nand s5pv210-nand: NAND ECC disabled
NAND device: Manufacturer ID: 0xec, Chip ID: 0xdc (Samsung NAND 512MiB 3,3V 8-bi
t), 512MiB, page size: 2048, OOB size: 64
NAND_ECC_NONE selected by board driver. This is not recommended!
Scanning device for bad blocks
Creating 5 MTD partitions on "NAND":
0x000000000000-0x000000800000 : "bootloader"
0x000000800000-0x000000820000 : "params"
0x000000820000-0x000000a20000 : "log"
0x000000a20000-0x000000d20000 : "kernel"
0x000000d20000-0x000020000000 : "rootfs"
dm9000 dm9000: read wrong id 0x01010101
eth0: dm9000a at a08a8000,a08aa004 IRQ 39 MAC: 00:09:c0:ff:ec:48 (platform data)
mousedev: PS/2 mouse device common for all mice
TCP: cubic registered
NET: Registered protocol family 17
VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 2
VFS: Mounted root (jffs2 filesystem) on device 31:4.
Freeing unused kernel memory: 136K (80379000 - 8039b000)
Kernel panic - not syncing: No init found. Try passing init= option to kernel.
See Linux Documentation/init.txt for guidance.
CPU: 0 PID: 1 Comm: swapper Not tainted 3.10.46 #35
[<800138b4>] (unwind_backtrace+0x0/0xf0) from [<8001176c>] (show_stack+0x10/0x14
)
[<8001176c>] (show_stack+0x10/0x14) from [<80295b34>] (panic+0x8c/0x1e
[<80295b34>] (panic+0x8c/0x1e from [<80295678>] (kernel_init+0xc0/0xe4)
[<80295678>] (kernel_init+0xc0/0xe4) from [<8000e458>] (ret_from_fork+0x14/0x3c)
有人遇到这种问题吗？是如何解决的？busybox尝试使用静态库编译也起不来！
另外有测试可以正常启动的busybox jffs2文件系统的话，麻烦发给我，我看看是不是我没压制好！
|
|
免费注册
发表于 2016-05-14 15:27
