- 论坛徽章:
- 0
|
p630启动时面板报B1114699错误
B1xx 4699
Service processor firmware:
This is usually an indication of a problem in the communication path between the HMC and the
service processor. It may only be an informational message.
If the managed system is down, go to the service processor error log and find the error log entry
containing B1xx 4699. Look at the first two bytes of word 13 of the detailed entry information.
If the managed system is running, look at the AIX error log entry containing B1xx 4699. This is a
²SCAN_ERROR_CHRP² error with an identifier of BFE4C025. In the detail data, find the string
²B1xx 4699². (If present, it will be at byte 60 of the detail data.) Go forward 8 bytes after the ²B1²
to byte 68 and look at bytes 68 and 69.
Perform the following actions based on the following values of bytes 68 and 69 from the AIX error
log entry, or on the first two bytes of word 13 from the service processor error log entry:
2306 No processor card is detected in slot one (U0.1-P1-C1); a processor card is required in
the first slot for the system to boot.
Actions:
1. If a processor card is not plugged into slot one (U0.1-P1-C1), plug one in.
2. If a processor card is plugged into slot one (U0.1-P1-C1), reseat it. If reseating the
processor card does not fix the problem, replace it.
A205: Machine type and model fields are not valid in the VPD module. Obtain an operator panel.
Do not swap the old VPD module onto the new operator panel. Call service support for
instructions on how to write the machine type and model into the new VPD module.
A20B: Error requesting trace buffer for service processor.
Actions:
1. Reset the service processor, if possible.
2. Check for system firmware updates. Apply the updates if they are available.
A218: Unknown return code detected.
Actions:
Check for system firmware updates. Apply the updates if they are available.
A21A: Error allocating an internal service processor memory space.
Actions:
1. Reset the service processor, if possible.
2. Check for system firmware updates. Apply the updates if they are available.
A800: HMC/service processor initialization failure.
Actions:
1. Check for system firmware updates.
2. Replace the service processor, location: U0.1-P1.
A801: HMC wrap failure.
Actions:
Replace the service processor, location: U0.1-P1.
A806: Loss of the surveillance heartbeat between the HMC and the service processor.
Actions:
1. Make sure that the HMC is booted and operational.
2. Check the serial cables that go from the HMC to the service processor, location:
U0.1-P1.
If there are no other error codes or indications of a problem, the A806 (loss of surveillance
heartbeat) was a temporary condition and has been resolved; the B1xx 4699 code is then
an informational message only.
If the problem persists:
1. Check the serial cables connecting the HMC to the CEC backplane, location: U0.1-P1.
2. Run diagnostics on the serial port on the HMC.
3. Run diagnostics on the serial ports on the service processor.
Values of A009 and A719 of bytes 68 and 69 in the AIX error log entry or the first two bytes of word
13 in the service processor error log entry are also informational entries:
A009: The system received a power-off request at run time from the HMC.
A719: Primary power failed; the system switched to battery backup power.
For all other values of bytes 68 and 69, or the first two bytes of word 13, do the following:
1. Check for system firmware updates.
2. Reset the service processor by activating the pinhole reset switch on the operator panel.
3. Call service support. |
|
免费注册
发表于 2003-08-18 17:21
发表于 2003-08-18 17:31
