HP 服务器安装 SCO UNIX 5.0.4/5（下）

2002hill

The SCSI configuration file has been updated.
Updating system configuration …
System files have been successfully updates.
Configuring Tape Driver ...(Stp)

Enter Vendor Identification string or press <Return>; to use default
Or enter q to return to main menu:

键人: HPTape
屏幕显示:
Enter SCSI version that device is conformant to or press <Return>; to use default or enter q to return to main menu:
键入 Enter
屏幕显示:
Enter Response Data Format that device uses or press <Return>; to use default or enter q to return to main menu:

键入Enter
屏幕显示:
The following tape drive types are supported:
1.Generic SCSI-1 / SCSI-2 Tape drive
2.EXABYTE 8mm tape drive (8200 or 8500)
3.IBM rebadged EXABYTE 8mm tape drive (8200)
4.DAT drive (Compressing and non-Compressing)
5.QIC Cartridge tape drive
Please choose one of the above, press <Return>; for default, or enter q to main menu:
键入4
屏幕显示:
Tape Driver Successfully Configured
Default special device have been created with the following links:
/dev/xct0linked to /dev/xStp0
/dev/rct0linked to /dev/rStp0and /dev/rmt/0b
/dev/nrct0linked to /dev/nrStp0and /dev/rmt/0bn
In /etc/default/boot:
No current boot string.
Enter New String, “rm” to remove string, or enter q to leave current string as is:
键入:q，屏幕显示:
SCSI or Enhanced IDE Tape Drive Configuration Program

1.Install a SCSI Tape Drive
2.Install an Enhanced IDE Tape Drive
3.Remove a SCSI Tape Drive
4.Remove an Enhanced IDE tape Drive
5.Change default Tape Drive
6.View Current SCSI and Enhanced IDE Tape Drive configuration

Select an option or enter q to return to main menu
键入q，屏幕显示：
Tape Drive Configuration Program

1. Configure a SCSI or Enhanced IDE tape drive
2. Configure a different type of tape drive
Select an option or enter q to quit:
You must create a new kernel to effect the drive change you specified
Do you wish to create a new kernel now? (y/n)

键入y，屏幕显示：
Do you want this kernel to boot by default? (y/n)
键入 y，屏幕显示：
Do you want the kernel environment rebuilt? (y/n)
  键入 y
安装完毕，重新引导系统，即可使用磁带机。
常用的磁带机读写命令
tar tvf /dev/rct0
tar cvf /dev/rct0 directory _name or filename
tar xvf /dev/rct0  
cpio –icuvdmB

30.      附加逻辑盘安装
Sco Unix不能自动识别附加逻辑盘，需要手动安装，有以下步骤：
(1)进入UNIX系统，在系统维护状态（单用户装态）下，键入命令
# mkdev hd
(2)屏幕显示
1)Add a hard disk to IDE controller
2)Add a hard disk to SCSI controller
3)Add a hard disk to IDA controller
(3)选择2
(4)屏幕显示：
Enter the prefix of the SCSI host adapter that supports this
      Device Or press <Return>; for the default: ‘slha’
      Enter h for a list of host adapters or enter q to quit:
      输入amird，然后敲Enter
(5)屏幕显示：
Which ‘amird’ SCSI host adapter supports this device?
Select 0-6, or enter q to quit :
      敲 0
(6)屏幕显示：
The Host Adapter parameters will be automatically configured
What SCSI Bus is this device attached to ?
Press <Return>; to use the default:0
Select 0-6, or h for help, or q to quit :
      敲 0
(7)屏幕显示：
What is the Target ID for this device?
Select 0-15, or h for help, or q to quit :
      敲 0
(屏幕显示：
What is the LUN of this device ?
Press <Return>; to use the default:0
Select 0-7, or h for help, or q to quit :
      敲 1
(9)屏幕显示：
You are about to add the following SCSI device:
Host AdapterAdapter
TypeDeviceNumberIDLUNBUS
amirdsdsk0010

Update SCSI configuration?(y/n)   ，      键入y
(10)屏幕显示：
The SCSI configuration file has been updated.
A new kernel must be built and rebooted before disk configuration can  
    continue.Would you like to relink at this time ? (y/n)
    敲y，系统重新链接内核，并reboot。
(11)因为加一块逻辑盘需要’mkdev hd’两次，所以重复过程(1)-(9)，     
      屏幕显示：Do you wish to continue? (y/n) ，敲y
(12)屏幕显示：
(1)Display Partition Table.
(2)Use Entire Disk for Unix
(3)Use Rest of Disk for Unix
(4)Create Unix Partition
(5)Activate Partition
(6)Delete Partition
(7)Create Partition
Enter your choice or q to quit:
      选择2，此时系统激活第二块逻辑盘
(13)出 现 (1) Print Current Bad Track Table
              (2) Scan Disk
  (3) Add Entries to Current Bad Table by Cylinder/Head number
        (4) Add Entries to Current Bad Track Table by sector number.
        (5) Delete Entries Individually from current Bad Track Table.
Enter  your  choice  or q to  quit.
敲 回 车。
(14)     出现Bad tracks have been identified
                 Enter the number of bad tracks to allocate space for (or press  
                 <return>; to use  the recommended valve of  19)
                                       敲 回 车。
(15)出 please enter swap-space allocation, or press <return>; to get the
              default allocation of 49000 1K block&#59;
            敲 回 车 (这 个 数 值 下 面 可 调， 它 指 的 是 内 存 的 对 换 区 的 大 小)
(16)出 Please enter boot-space allocation, or press <return>; to get the default allocation of 15000 1K block.
            敲 回 车
(17)出 Do you wish to make any manual adjustments to the sizes or names of the file systems on swap area before they are create on the hard disk? (Y/N)
             敲 回 车 ( 提 示 是 否 要 对 上 面 参 数 进 行 调 整)
(1屏幕显示:
             Do you wish to make any manual adjustments to the size or name of the
             file systems or  Swap area before they are create on the hard disk? (y/n)
             输入: y  并按 Enter
(19)屏幕显示:
NameTypeNew FS#First BlockLast Block
RootSwapRootScratchRecoverHd0aEAFSNON FSHTFSNOT USEDNOT USEDNON FSNON FSWhole disknononononononono01234567020000118000--206239520643420199991179992062394--206434120643512072352

n[ame]Name or rename a division
c[reate]Create a new file system on this division
t[ype]Select or Change filesystem type on new filesystem
p[revent]Prevent a new filesystem from being created on this  
                                    division
s[tart]Start a division on a different block
e[nd]End a division on a different block
r[estore]Restore the original division table
Enter your choices or q to quit:
                 根据提示 按  'e' 设定分区的结尾的块值。
           'n' 给相应分区命名。
           'r' 恢复原分区。
                  分区划分满意后，按 q 并回车。
(20)屏幕显示:
  I[nstall] Install the division Set Up shown
    R[return] Return the previous menu
          Please enter your choice:
          按i并回车
(21)屏幕显示:
          root file system is large enough that fsck will require a scratch
          division of 936 blocks to clean it, Would you like a scratch division to
          be allocated for you?  (y/n)
          敲入y并回车
(22)屏幕显示:
          Remove the floppy disk from the drive, then Press any key
          取出软盘,按任意键，退出依系统提示重新链接内核并reboot, 第二块逻辑
          盘就安装成功了。

  31.   设置显示卡和分辨率
          以系统维护状态（单用户装态）下进入UNIX系统，在，键入命令 ‘ scoadmin’，
          进入管理菜单。
（1）在管理菜单中选择‘Video Configuration Manager’，进入‘显示设置管理’
（2）选择‘Add adapter’项，在显示卡驱动库中选中‘Cirrus Logic GD5446’一项。
（3）用户如果是14’显示器，‘Monitor’选择’other 14 inch’一项。
（4）Resolution’可以设成‘VGA 640*480 256 color 60Hz’。
（5）重新连接内核。重新启动，显示卡设置完成。

天明700

收下
谢谢！