boot net 问题

mtykillyou

使用jumpstart安装的时候 在server 使用 snoop client 出现到如下就停止了\r\n\r\nclient -> server       TFTP Ack  block 309\r\n    server  -> client   TFTP Data block 310 (512 bytes)\r\n client -> server        TFTP Ack  block 310\r\n    server  -> client    TFTP Data block 311 (512 bytes)\r\n client -> server       TFTP Ack  block 311\r\n    server  -> client   TFTP Data block 312 (512 bytes)\r\n client -> server        TFTP Ack  block 312\r\n    server  -> client    TFTP Data block 313 (256 bytes) (last block)\r\n client -> server       TFTP Ack  block 313\r\n client -> BROADCAST    BPARAM C WHOAMI? 192.168.0.1\r\n    server  -> client   BPARAM R WHOAMI? client in\r\nclient -> server      BPARAM C GETFILE root\r\n    server  -> client   BPARAM R GETFILE File=/install/Solaris_8/Tools/Boot\r\n\r\n在client端就停止了 请问。。。。。

briangao

Make sure your install directory is NFS shared on the server

mtykillyou

bash-2.03# dfshares\r\nRESOURCE                                  SERVER ACCESS    TRANSPORT\r\n    server:/install                          server  -         -\r\n    server:/jump/sysid                    server  -         -\r\n    server:/jump/jumpstart_sample         server  -         -

race

该文件系统（分区）上只能NFS共享安装服务器目录，你得把多余的禁止掉。

briangao

If /install is already NFS shared, then the problem is your bootparams file, which is updated when you issued add_install_client. Couple of things to check.\r\n\r\n1. ls   /install/Solaris_8/Tools/Boot to verify the directory is your miniroot (You should see the contents as you would see in a root directory) \r\n2. rm_install_client client_name and redo add_install_client. Make sure you have the right path for sysidcfg file, install directory and class file directory. Make sure machine architecture such as sun4u is right

mtykillyou

Rebooting with command: boot net -v - install\r\nBoot device: /pci@1f,4000/network@1,1  File and args: -v - install\r\nTimeout waiting for ARP/RARP packet\r\n2b000 Using RARP/BOOTPARAMS...\r\nInternet address is: 192.168.0.1\r\nhostname: client\r\nFound 192.168.0.99@ 0:3:ba:68:6c:9a\r\nroot server: server (127.0.0.1)\r\nroot directory: /install/Solaris_8/Tools/Boot\r\nFound 127.0.0.1 @ 0:e0:fc:61:30:4e\r\n\r\n然后就停止了 其中0:e0:fc:61:30:4e代表的网卡地址用arp -a 查看 是server上的default 路由\r\n192.168.0.99 是server

nus

原帖由 mtykillyou 于 2007-2-27 16:48 发表\r\nRebooting with command: boot net -v - install\r\nBoot device: /pci@1f,4000/network@1,1  File and args: -v - install\r\nTimeout waiting for ARP/RARP packet\r\n2b000 Using RARP/BOOTPARAMS...\r\nInternet addr ...

\r\n\r\n\r\n貌似boot server和client必须在同一个广播域（同一网段）， 难道现在不是？\r\n\r\npf一下briangao

briangao

Good point from nus. Boot server and client must be on the same subnet.