系统报错！！！！！急

ims2002

大哥，小弟是新来的，现在有急事求救

Mar 25 17:42:32 nttmgmt dmfe: NOTICE: dmfe1: PHY 1 link up 100 Mbps Full-Duplex
Mar 25 17:46:58 nttmgmt in.mpathd[36]: Improved failure detection time 1000 ms
Mar 25 17:47:39 nttmgmt uxwdog[286]: server initialization failed (Interrupted s
ystem call)
Mar 25 17:42:46 nttmgmt lom: 3/26/2003 1:42:46 GMT LOM time reference
Mar 25 17:42:49 nttmgmt inetd[147]: 100153/rpc/udp version 1: rpcb_set: not star
ted
Mar 25 17:42:49 nttmgmt automountd[148]: svc_create: cannot register 100099 vers
4 on ticotsord
Mar 25 17:46:58 nttmgmt in.mpathd[36]: Improved failure detection time 1680 ms
Mar 25 17:45:57 nttmgmt in.mpathd[36]: Cannot meet requested failure detection t
ime of 1000 ms on (inet dmfe0) new failure detection time is 3360 ms
Mar 25 17:42:49 nttmgmt automountd[148]: unable to create service
Mar 25 17:42:06 nttmgmt genunix: Copyright 1983-2001 Sun Microsystems, Inc. All
rights reserved.
Mar 25 17:42:24 nttmgmt genunix: WARNING: forceload of misc/md_trans failed
Mar 25 17:42:24 nttmgmt genunix: WARNING: forceload of misc/md_raid failed
Mar 25 17:42:32 nttmgmt dmfe: NOTICE: dmfe0: PHY 1 link up 100 Mbps Full-Duplex
Mar 25 17:43:34 nttmgmt login: ROOT LOGIN /dev/pts/1 FROM 47.153.178.140
Mar 25 17:42:32 nttmgmt dmfe: NOTICE: dmfe1: PHY 1 link up 100 Mbps Full-Duplex
Mar 25 17:46:58 nttmgmt in.mpathd[36]: Improved failure detection time 1000 ms

SUN V100机器，SOLARIS 8操作系统，系统启动后不停的报上面的错，任何指令都无法执行，包括break,/var区很快就满了，那位大哥给看看，很急。小弟先谢了

feng4321

Possibly the switch port that V100 is plugged into is hard set to
half/full duplex, where as your NIC card is set to autonegotiate. Check
your ndd settings to see how the NIC is set and make sure it is the same
(either both are hard coded, or both are auto detect) as the switch port.

-----

Is duplexing set to 100 FDX or auto on your switch?  It could be
something as lame as a bad cable too.
能进入ok>;么？

johnyou

boot cdrom -s 看看。

Philmoon

in.mpathd是检测网卡的daemon，它不停报错说明网卡有问题。按feng4321的方法试试。

ims2002

多谢个位指点。

ims2002

能详细点吗？如何用ndd命令，谢谢

power off/power on后可以进ok，但用户也可以

feng4321

看看man  ndd
ndd /dev/ip \?查看设备

实在不行,就stop-n
恢复默认值试试。没办法再做呀

Philmoon

# ndd /dev/hme link_status     检查连接状态，1=ON
# ndd /dev/hme link_speed      检查连接速度，1=100M
# ndd -set /dev/hme link_speed 1    如果不是1，设置为1（如果你是用100M网的话）

# ndd /dev/hme \?   列出关于网卡的参数

ims2002

谢谢