请高手执教呀！急！！！！！！！！（在线等）

duron_1g

我要通过26路由器拨号到36路由器上面，可是运行这个配置。我的想法是如果有数据包比如PING的时候AUX口就启动拨号，可是现在就是无法启动拨号，当我在特权模式输入错误的命令后，如果启动了广播，这个时候拨号也启动而且能正常的拨号到36上面去了，不知道哪里有问题！我写了以下2个配置请看看：

Current configuration : 1052 bytes
!
version 12.2
service timestamps debug uptime
service timestamps log uptime
service password-encryption
!
hostname jjshkjb
!
enable secret 5 $1$Q5bF$6BLAwYnEnYB1iBad.Z/gJ.
!
username jj3640 password 7 08395D4200151C
memory-size iomem 25
ip subnet-zero
!
!
!
chat-script ddr ABORT ERROR "" "AT Z" OK "ATDT\T" TIMEOUT 60 "CONNECT"\P
!
!
interface FastEthernet0/0
ip address 192.50.1.10 255.255.255.0
duplex auto
speed auto
!
interface Serial0/0
no ip address
shutdown
!
interface Async65
ip address 198.10.1.20 255.255.255.0
encapsulation ppp
dialer in-band
dialer map ip 198.1.1.1 name jj3640 modem-script ddr broadcast 8138202
dialer-group 1
dialer idle-timeout 120
async default routing
async mode dedicated
ppp authentication chap
!
ip classless
ip route 0.0.0.0 0.0.0.0 198.1.1.1 100
no ip http server
ip pim bidir-enable



!
!
dialer-list 1 protocol ip permit
!
line con 0
line aux 0
modem InOut
transport input all
flowcontrol hardware
line vty 0 3
password 7 095F4B0A0B00035201061722202E2A
login
line vty 4
password 7 141D1818040F2029
login
!
!!
end




Current configuration : 1183 bytes
!
version 12.2
service timestamps debug uptime
service timestamps log uptime
service password-encryption
!
hostname jjhk
!
enable secret 5 $1$V7tO$jQq3F9YL13L.QboHcpyA3/
!
username jj3640 password 7 04431A0A062D55
memory-size iomem 25
ip subnet-zero
!
!
!
chat-script cisco-default "" "AT" TIMEOUT 30 OK "ATDT \T" TIMEOUT 30 CONNECT \c

chat-script reset atz
!
!
!
interface FastEthernet0/0
ip address 192.50.1.10 255.255.255.0
duplex auto
speed auto
!
interface Serial0/0
backup delay 5 10
backup interface Async65
no ip address
encapsulation ppp
no ip mroute-cache
no fair-queue
!
interface Async65
ip address 198.10.1.20 255.255.255.0
encapsulation ppp
keepalive 145
dialer in-band
dialer idle-timeout 60
dialer map ip 198.1.1.1 name jj3640 modem-script ddr broadcast 8138202
dialer-group 1
async default routing
async mode dedicated
ppp authentication chap
!
ip classless
ip route 0.0.0.0 0.0.0.0 198.1.1.1 100
no ip http server
ip pim bidir-enable
!
!
dialer-list 1 protocol ip permit
!
line con 0
line aux 0
modem InOut
transport input all
flowcontrol hardware
line vty 0 3
password 7 1044030A0D
login
line vty 4
password 7 01190C1753
login
!
!
end



Building configuration...

Current configuration : 1183 bytes
!
version 12.2
service timestamps debug uptime
service timestamps log uptime
service password-encryption
!
hostname jjhk
!
enable secret 5 $1$V7tO$jQq3F9YL13L.QboHcpyA3/
!
username jj3640 password 7 04431A0A062D55
memory-size iomem 25
ip subnet-zero
!
!
!
chat-script cisco-default "" "AT" TIMEOUT 30 OK "ATDT \T" TIMEOUT 30 CONNECT \c

chat-script reset atz
!
!
!
interface FastEthernet0/0
ip address 192.50.1.10 255.255.255.0
duplex auto
speed auto
!
interface Serial0/0
backup delay 5 10
backup interface Async65
no ip address
encapsulation ppp
no ip mroute-cache
no fair-queue
!
interface Async65
ip address 198.10.1.20 255.255.255.0
encapsulation ppp
keepalive 145
dialer in-band
dialer idle-timeout 60
dialer map ip 198.1.1.1 name jj3640 modem-script ddr broadcast 8138202
dialer-group 1
async default routing
async mode dedicated
ppp authentication chap
!
ip classless
ip route 0.0.0.0 0.0.0.0 198.1.1.1 100
no ip http server
ip pim bidir-enable
!
!
dialer-list 1 protocol ip permit
!
line con 0
line aux 0
modem InOut
transport input all
flowcontrol hardware
line vty 0 3
password 7 1044030A0D
login
line vty 4
password 7 01190C1753
login
!
!
end

xigua

"我的想法是如果有数据包比如PING的时候AUX口就启动拨号"

没弄明白
你是想按需拨号吗?
那你没有定义呀
你可以用ACL.