SUN的机器在把光驱取下来重装了之后就起不来了!

sun_cu

公司有台老的SUN 机器!  前两天因为需要把光驱下了,后来装上去 系统就起不来了!

提示:

Can't clear FAS interrupts; Check SCSI Term. Power Fuse.

Can't clear FAS interrupts; Check SCSI Term. Power Fuse.
sd st SUNW,hme SUNW,bpp
Probing /sbus@1f,0 at 0,0 cgsix
Probing /sbus@1f,0 at 0,0 Nothing there


...........................................省略
...........................................省略
Ethernet address ee:cf:ff:bf:ff:ff, Host  ID : efbefeff.

The IDPROM conterts are invalid

Power On  Self  Test Failed .  Cause;

OK


请各位帮忙看看!!
因为这台机器的确太老了,PROM 本来就没电了!  导致Ethernet  ddress  错误!
每次开机都需要boot disk

但现在boot disk   显示:
Boot  device :  /sbus/SUNW,fas@e. 8800000/sd@0,0  File  and args:

Can't  clear  FAS  interrupts; Check  SCSI  Term, Power Fuse.

Can't  clear  FAS  interrupts; Check  SCSI  Term, Power Fuse.

Can't  clear  FAS  interrupts; Check  SCSI  Term, Power Fuse.

Can't  clear  FAS  interrupts; Check  SCSI  Term, Power Fuse.

Can't  clear  FAS  interrupts; Check  SCSI  Term, Power Fuse.

Can't  clear  FAS  interrupts; Check  SCSI  Term, Power Fuse.

Can't  clear  FAS  interrupts; Check  SCSI  Term, Power Fuse.

Cant' open boot device

OK

lyh003473

什么机器呀

suncookie

scsi线插进了吗？

sun_cu

Ultra 1 ... 老机器了!  
..........................
scsi 线插进去了啊!
..........................
我把光驱卸了,系统又起来了! 可是这样,光驱就没法用了啊!!

这是哪里的原因了??

liuhao75926

scsi跳线问题？电源问题？

sun_cu

原帖由 liuhao75926 于 2006-8-23 13:42 发表
scsi跳线问题？电源问题？

I don't know!

sun_cu

问题还没解决!!
高手们帮我看看哈!!  

启动信息:
Can't clear FAS interrupts; Check SCSI Term. Power Fuse.

Can't clear FAS interrupts; Check SCSI Term. Power Fuse.
sd st SUNW,hme SUNW,bpp
Probing /sbus@1f,0 at 0,0 cgsix
Probing /sbus@1f,0 at 0,0 Nothing there


...........................................省略
...........................................省略
Ethernet address ee:cf:ff:bf:ff:ff, Host  ID : efbefeff.

The IDPROM conterts are invalid

Power On  Self  Test Failed .  Cause;

OK


请各位帮忙看看!!
因为这台机器的确太老了,PROM 本来就没电了!  导致Ethernet  ddress  错误!
每次开机都需要boot disk

但现在boot disk   显示:
Boot  device :  /sbus/SUNW,fas@e. 8800000/sd@0,0  File  and args:

Can't  clear  FAS  interrupts; Check  SCSI  Term, Power Fuse.

Can't  clear  FAS  interrupts; Check  SCSI  Term, Power Fuse.

Can't  clear  FAS  interrupts; Check  SCSI  Term, Power Fuse.

Can't  clear  FAS  interrupts; Check  SCSI  Term, Power Fuse.

Can't  clear  FAS  interrupts; Check  SCSI  Term, Power Fuse.

Can't  clear  FAS  interrupts; Check  SCSI  Term, Power Fuse.

Can't  clear  FAS  interrupts; Check  SCSI  Term, Power Fuse.

Cant' open boot device

OK

race

看看硬盘接好了没有？

sun_cu

原帖由 race 于 2006-9-6 14:28 发表
看看硬盘接好了没有？

硬盘 接好了!

我把光驱拔下来 系统就能正常启动了!

插上去之后 就是这个样子的了!!

race

那就是光驱线出问题了。