请问cx600 Event Code:0x71310008是什么类型的信息？急

zuobaoyu

1.
Date:01/11/2008
Time:03:41:00 下午
Event Code:0x71310008
Description:CMID Transport Device 2: Gate 0 connects to SP ID 0x9b03609060010650:0 (Signature 0xac26b)   00 00 04 00 06 00 4e 00 d3 04 00 00 08 00 31 61 08 00 31 61 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 71 31 00 08
Subsystem:CK200024500227
Device:N/A
SP:N/A
Host:SHTAX-MAIN-SPA
Source:cmid
Category:NT System Log
Log:NT System Log
Sense Key:N/A
Ext Code1:N/A
Ext Code2:N/A
Type:Information


2.
Date:01/11/2008
Time:03:41:00 下午
Event Code:0x71310008
Description:CMID Transport Device 2: Gate 0 connects to SP ID 0x9b03609060010650:0 (Signature 0xac26b)   00 00 04 00 06 00 4e 00 d3 04 00 00 08 00 31 61 08 00 31 61 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 71 31 00 08
Subsystem:CK200024500227
Device:N/A
SP:N/A
Host:SHTAX-MAIN-SPA
Source:cmid
Category:NT System Log
Log:NT System Log
Sense Key:N/A
Ext Code1:N/A
Ext Code2:N/A
Type:Information

zuobaoyu

最近发现CX600不断地有Event Code:0x71310008提示信息，请教此类信息的含义，以及什么条件下会触发这类的信息的产生，请知道的兄弟告诉一下，多谢多谢。

tyr1

Event Code:0x71310008　故障代码手册没有，此类代码为信息代码，一般的正常信息，不代表任何故障问题代码。

星海夜航

"Logs filled with '(71310007)CMID Transport Device 1: 0 gate(s) found. or: (71180009)CMI Transport Device 1: 0 gate(s) found' messages"

Knowledgebase Solution   
   

Environment:  Product: CLARiiON CX-Series
Environment:  EMC SW: MirrorVIew
Problem:  Logs filled with '(71310007)CMID Transport Device 1: 0 gate(s) found. or: (71180009)CMI Transport Device 1: 0 gate(s) found' messages
Problem:  Event logs filling up 7131007 or 71180009 errors.
Problem:  11/20/2005 16:03:35 (71310007)CMID Transport Device 2: 0 gate(s) found. 00 00 04 00 03 00 4e 00 d3 04 00 00 07 00 31 61 07 00 31 61 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 71 31 00 07 cmid

11/20/2005 16:03:35 (71310007)CMID Transport Device 2: 0 gate(s) found. 00 00 04 00 03 00 4e 00 d3 04 00 00 07 00 31 61 07 00 31 61 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 71 31 00 07 cmid

Change:  Battery test 16 hours ago.
Root Cause:  These are MirrorView messages. This site has Cisco switches and the Cisco Fibre Channel Protocol (FCP) pings the MirrorView ports when Fabric Manager or Device Manager is enabled and licensed. FCP tries to log in on all known initiators. When MirrorView is enabled on the array, the MirrorView ports are initiators and targets. FCP reaches the MirrorView ports and then the CMI Transport Device checks whether the initiator is a valid array. If it is not, the "0 gate(s) found" messages are returned. The messages can provide important information at MirrorView sites where fabric problems exist. Often these events are the only information that allows serious switch configuration problems to be identified.
Fix:  These are informational messages returned by the CLARiiON array that the CMI Transport Device found. The messages can usually be ignored and no action is required. A future release of FLARE/MirrorView may reduce the number of messages returned.
Notes:  FCP is a storage interface mapping protocol.

[ 本帖最后由 星海夜航 于 2008-1-15 15:27 编辑 ]

xiaomao2006

shoudao