[求助]安装系统的时候碰到系统不支持的scsi卡

coolzsb

其实就是在装vmware esx啦，它默认的不支持我的那块该死的scsi卡，每次安装到检测scsi卡的情况下就只能退出安装。所以要请教一下，如何在安装过程中添加该scsi卡的驱动？

我看vmware esx的系统也就是一个改过的redhat，请有经验的朋友谈谈

fushuyong

你是从SCSI启动吗？ 如果不是的话，你可以先把SCSI拔掉，将系统安装完毕后，安装SCSI的驱动，再将SCSI插上去，这样就OK了。如果你的系统上只有SCSI，而且要从SCSI启动的话，就有点麻烦了。

coolzsb

原帖由 "fushuyong"]你是从SCSI启动吗？ 如果不是的话，你可以先把SCSI拔掉，将系统安装完毕后，安装SCSI的驱动，再将SCSI插上去，这样就OK了。如果你的系统上只有SCSI，而且要从SCSI启动的话，就有点麻烦了。

[list 发表：



我想知道的就是该怎么做那个“有点麻烦”

fushuyong

既然你要麻烦的，那就给你个麻烦的，我打出来都麻烦哦，只好给你复制一个过来，是安装promise的，其他的一样的做法，自己麻烦点，先将就着看吧。
1.) Start the Red Hat Linux Installation with CD-ROM booting.

  2.) At the "Welcome to Red Hat Linux ..." installation screen, a prompt
      labeled "boot:" will appear at the bottom of the screen.

  3.) Please append parameters (see Note 1 below) at the "boot:" prompt,
      then press the Enter key.

  4.) At the "Devices" dialog box, insert the FastTrak Driver Disk in the
      floppy drive and then select "OK" or "Yes" to continue install.

  5.) Enable "Configure advanced boot loader options" box at Boot Loader
      Configuration menu, and type kernel parameters (see NOTE 2 below)
      in the General kernel parameters field.

  6.) Continue with the installation as normal.

  7.) If the installer occur warning message about "The kernel was unable
      to re-read the partition table on /dev/sd(x), (Device or resource
      busy)...", Please do not click skip, just click Ignore bottom to
      continue the install.

  8.) Press Ctrl-Alt-F2 when installation at the "Congratulations" menu.

  9.) Insert the FastTrak Driver Disk floppy, Issue commands to load FastTrak
      driver.
                # umount /tmp/fd0        (Just in case if RedHat forgot this)

                # chroot /mnt/sysimage
                # mount /dev/fd0 /mnt       
        (If USB Floppy, Please choose USB floppy device such as /dev/sdb)
                # cd /mnt
                # sh setup-ft
                    
  10.) Choose your selection here, after FastTrak driver setup successful.
                # cd /
                # umount /mnt
                # exit

  11.) Please press Ctrl-Alt-F7 and click "Exit" button to finish installation.


[NOTE]

   Linux Kernels 2.4.x misidentiy Promise ATA-RAID controllers as simple
IDE controllers. This results in the built-in Linux IDE driver trying to
handle the controller and can prevent the proper FastTrak ATA RAID driver
from loading.
   Follow the installation instructions AND the parameter commands referred
to below section. This status we called "IDE issue".

   1.) "linux ide0=0x1f0,0x3f6,14 ide1=0x170,0x376,15 ide2=0 ide3=0 ide4=0
        ide5=0 ide6=0 ide7=0 ide8=0 ide9=0 expert"

   2.) "ide0=0x1f0,0x3f6,14 ide1=0x170,0x376,15 ide2=0 ide3=0 ide4=0 ide5=0
        ide6=0 ide7=0 ide8=0 ide9=0"

   3.) Occasionally, during bootup, you may see Unresolved Symbols, followed
       by an OK or a FAILED. In either case, this is a cosmetic error and
       does not affect RedHat Linux 7.3 or the FastTrak RAID Controller card.

   4.) Rarely, during bootup, you may see a HUSH (humble shell) message. This
       is also a cosmetic error and does not affect RedHat Linux 7.3 or the
       FastTrak RAID Controller card.

   5.) To see information on your array(s) and the Driver version number:

       a. Launch your terminal emulation program.

       b. Type "cat /proc/scsi/FastTrak/(x)" then press Enter, x is a SCSI
          register number in your system.

coolzsb

多谢，能不能给个相关的链接，还有一些具体的东西还不是很清楚

fushuyong

这个已经讲的很具体了啊。 这就是一个具体的安装步骤。
你看看你的SCSI是什么品牌，然后到网站上去找到他的驱动程序，
看看里面的readme文件不就可以了。