论坛徽章:: 0

电梯直达

1楼 [收藏(0)] [报告]

发表于 2005-06-21 09:45 |只看该作者 |倒序浏览

两台E250同时链接至A1000，一台设备可以正常连接并已经可以用rm6配置A1000。在OK状态下，probe-scsi-all正常可以检测A1000。\r\n\r\n但在另外一台设备上使用probe-scsi-all时，检测到/pci@1f,4000/scsi@2时就无响应（第一台机器是关着的），在这台机器上仅比第一台设备多一个内置磁带机。\r\nprobe-scsi可以正常结束，DVD-rom和Tape的Target分别是6和4，已经修改了scsi-initiator-id 至5，并编辑了nvedit，5 encode-int \" scsi-initiator-id\" property。\r\n如果启动系统则会报connected command timeout for target 12.0\r\n和get scsi bus reset。\r\n\r\n进入系统后dmesg，得到以下Log\r\n\r\nscsi: [ID 365881 kern.info] /pci@1f,4000/scsi@2 (glm2):\r\n cdb=[ 0x12 0x0 0x0 0x0 0x30 0x0 ]\r\nscsi: [ID 365881 kern.info] /pci@1f,4000/scsi@2 (glm2):\r\n pkt_flags=0x808 pkt_statistics=0x60 pkt_state=0x7\r\nscsi: [ID 365881 kern.info] /pci@1f,4000/scsi@2 (glm2):\r\n pkt_scbp=0x0 cmd_flags=0x2860\r\nscsi: [ID 107833 kern.warning] WARNING: /pci@1f,4000/scsi@2 (glm2):\r\n Connected command timeout for Target 12.0\r\ngenunix: [ID 408822 kern.info] NOTICE: glm2: fault detected in device; service still available\r\ngenunix: [ID 611667 kern.info] NOTICE: glm2: Connected command timeout for Target 12.0\r\nglm: [ID 280919 kern.warning] WARNING: ID[SUNWpd.glm.cmd_timeout.6017]\r\nscsi: [ID 107833 kern.warning] WARNING: /pci@1f,4000/scsi@2 (glm2):\r\n got SCSI bus reset\r\ngenunix: [ID 408822 kern.info] NOTICE: glm2: fault detected in device; service still available\r\ngenunix: [ID 611667 kern.info] NOTICE: glm2: got SCSI bus reset\r\nswapgeneric: [ID 308332 kern.info] root on /pci@1f,4000/scsi@3/disk@0,0:a fstype ufs\r\nkrtld: [ID 469452 kern.info] NOTICE: sf: 64-bit driver module not found\r\nlast message repeated 1 time\r\npcipsy: [ID 370704 kern.info] PCI-device: ebus@1, ebus0\r\ngenunix: [ID 936769 kern.info] ebus0 is /pci@1f,4000/ebus@1\r\nebus: [ID 521012 kern.info] envctrltwo0 at ebus0: offset 14,600000\r\ngenunix: [ID 936769 kern.info] envctrltwo0 is /pci@1f,4000/ebus@1/SUNW,envctrltwo@14,600000\r\nebus: [ID 521012 kern.info] su0 at ebus0: offset 14,3083f8\r\ngenunix: [ID 936769 kern.info] su0 is /pci@1f,4000/ebus@1/su@14,3083f8\r\nebus: [ID 521012 kern.info] su1 at ebus0: offset 14,3062f8\r\ngenunix: [ID 936769 kern.info] su1 is /pci@1f,4000/ebus@1/su@14,3062f8\r\npcipsy: [ID 370704 kern.info] PCI-device: TSI,gfxp@1, gfxp0\r\ngenunix: [ID 936769 kern.info] gfxp0 is /pci@1f,2000/TSI,gfxp@1\r\ngfxp: [ID 722914 kern.notice] TSI: gfxp0 is GFX8P @ 640x480\r\nunix: [ID 987524 kern.info] cpu0: SUNW,UltraSPARC-II (upaid 0 impl 0x11 ver 0xa0 clock 400 MHz)\r\nebus: [ID 521012 kern.info] se0 at ebus0: offset 14,400000\r\ngenunix: [ID 936769 kern.info] se0 is /pci@1f,4000/ebus@1/se@14,400000\r\nebus: [ID 521012 kern.info] se1 at ebus0: offset 14,200000\r\ngenunix: [ID 936769 kern.info] se1 is /pci@1f,4000/ebus@1/se@14,200000\r\nhme: [ID 517527 kern.info] SUNW,hme0 : PCI IO 2.0 (Rev Id = c1) Found\r\npcipsy: [ID 370704 kern.info] PCI-device: network@1,1, hme0\r\ngenunix: [ID 936769 kern.info] hme0 is /pci@1f,4000/network@1,1\r\ngenunix: [ID 454863 kern.info] dump on /dev/dsk/c0t0d0s1 size 2001 MB\r\nhme: [ID 517527 kern.info] SUNW,hme0 : Internal Transceiver Selected.\r\nhme: [ID 517527 kern.info] SUNW,hme0 : 10 Mbps Half-Duplex Link Up\r\npseudo: [ID 129642 kern.info] pseudo-device: devinfo0\r\ngenunix: [ID 936769 kern.info] devinfo0 is /pseudo/devinfo@0\r\npseudo: [ID 129642 kern.info] pseudo-device: tod0\r\ngenunix: [ID 936769 kern.info] tod0 is /pseudo/tod@0\r\npseudo: [ID 129642 kern.info] pseudo-device: pm0\r\ngenunix: [ID 936769 kern.info] pm0 is /pseudo/pm@0\r\nThere are no devices (controllers) in the system; nvutil terminated.\r\nThere are no devices (controllers) in the system.\r\n\r\nfwutil failed!\r\nArray Monitor initiated\r\n/usr/lib/osa/bin/arraymon: [ID 712306 user.error] No RAID devices found to check.\r\nRDAC daemons initiated\r\nrdriver: [ID 400281 kern.notice] ID[RAIDarray.rdaemon.1001] RDAC Resolution Daemon locked in memory\r\npseudo: [ID 129642 kern.info] pseudo-device: vol0\r\ngenunix: [ID 936769 kern.info] vol0 is /pseudo/vol@0\r\nebus: [ID 521012 kern.info] se0 at ebus0: offset 14,400000\r\ngenunix: [ID 936769 kern.info] se0 is /pci@1f,4000/ebus@1/se@14,400000\r\nebus: [ID 521012 kern.info] se1 at ebus0: offset 14,200000\r\ngenunix: [ID 936769 kern.info] se1 is /pci@1f,4000/ebus@1/se@14,200000\r\npseudo: [ID 129642 kern.info] pseudo-device: pm0\r\ngenunix: [ID 936769 kern.info] pm0 is /pseudo/pm@0\r\nreboot: [ID 662345 auth.crit] rebooted by root\r\nsyslogd: going down on signal 15\r\ngenunix: [ID 672855 kern.notice] syncing file systems...\r\ngenunix: [ID 904073 kern.notice] done\r\ngenunix: [ID 540533 kern.notice] ^MSunOS Release 5.9 Version Generic 64-bit\r\ngenunix: [ID 172905 kern.notice] Copyright 1983-2002 Sun Microsystems, Inc. All rights reserved.\r\nUse is subject to license terms.\r\ngenunix: [ID 678236 kern.info] Ethernet address = 0:3:ba:2:30:8a\r\nunix: [ID 389951 kern.info] mem = 1048576K (0x40000000)\r\nunix: [ID 930857 kern.info] avail mem = 1021526016\r\nrootnex: [ID 466748 kern.info] root nexus = Sun (TM) Enterprise 250 (UltraSPARC-II 400MHz)\r\nrootnex: [ID 349649 kern.info] pcipsy0 at root: UPA 0x1f 0x4000\r\ngenunix: [ID 936769 kern.info] pcipsy0 is /pci@1f,4000\r\nrootnex: [ID 349649 kern.info] pcipsy1 at root: UPA 0x1f 0x2000\r\ngenunix: [ID 936769 kern.info] pcipsy1 is /pci@1f,2000\r\nscsi: [ID 365881 kern.info] /pci@1f,4000/scsi@3 (glm0):\r\n initiator SCSI ID now 5\r\nscsi: [ID 365881 kern.info] /pci@1f,4000/scsi@3 (glm0):\r\n Rev. 5 Symbios 53c876 found.\r\nscsi: [ID 365881 kern.info] /pci@1f,4000/scsi@3 (glm0):\r\n target1-scsi-options=0x5f8\r\nscsi: [ID 365881 kern.info] /pci@1f,4000/scsi@3 (glm0):\r\n target2-scsi-options=0x5f8\r\nscsi: [ID 365881 kern.info] /pci@1f,4000/scsi@3 (glm0):\r\n target3-scsi-options=0x5f8\r\nscsi: [ID 365881 kern.info] /pci@1f,4000/scsi@3 (glm0):\r\n target4-scsi-options=0x5f8\r\nscsi: [ID 365881 kern.info] /pci@1f,4000/scsi@3 (glm0):\r\n target5-scsi-options=0x5f8\r\nscsi: [ID 365881 kern.info] /pci@1f,4000/scsi@3 (glm0):\r\n target6-scsi-options=0x5f8\r\npcipsy: [ID 370704 kern.info] PCI-device: scsi@3, glm0\r\ngenunix: [ID 936769 kern.info] glm0 is /pci@1f,4000/scsi@3\r\nscsi: [ID 365881 kern.info] /pci@1f,4000/scsi@3,1 (glm1):\r\n initiator SCSI ID now 5\r\nscsi: [ID 365881 kern.info] /pci@1f,4000/scsi@3,1 (glm1):\r\n Rev. 5 Symbios 53c876 found.\r\npcipsy: [ID 370704 kern.info] PCI-device: scsi@3,1, glm1\r\ngenunix: [ID 936769 kern.info] glm1 is /pci@1f,4000/scsi@3,1\r\nscsi: [ID 365881 kern.info] /pci@1f,4000/scsi@2 (glm2):\r\n initiator SCSI ID now 6\r\nscsi: [ID 365881 kern.info] /pci@1f,4000/scsi@2 (glm2):\r\n Rev. 5 Symbios 53c876 found.\r\npcipsy: [ID 370704 kern.info] PCI-device: scsi@2, glm2\r\ngenunix: [ID 936769 kern.info] glm2 is /pci@1f,4000/scsi@2\r\nscsi: [ID 365881 kern.info] /pci@1f,4000/scsi@2,1 (glm3):\r\n initiator SCSI ID now 6\r\nscsi: [ID 365881 kern.info] /pci@1f,4000/scsi@2,1 (glm3):\r\n Rev. 5 Symbios 53c876 found.\r\npcipsy: [ID 370704 kern.info] PCI-device: scsi@2,1, glm3\r\ngenunix: [ID 936769 kern.info] glm3 is /pci@1f,4000/scsi@2,1\r\nscsi: [ID 193665 kern.info] sd0 at glm0: target 0 lun 0\r\ngenunix: [ID 936769 kern.info] sd0 is /pci@1f,4000/scsi@3/sd@0,0\r\nscsi: [ID 193665 kern.info] sd6 at glm0: target 6 lun 0\r\ngenunix: [ID 936769 kern.info] sd6 is /pci@1f,4000/scsi@3/sd@6,0\r\nscsi: [ID 193665 kern.info] sd7 at glm0: target 8 lun 0\r\ngenunix: [ID 936769 kern.info] sd7 is /pci@1f,4000/scsi@3/sd@8,0\r\nscsi: [ID 365881 kern.info] /pci@1f,4000/scsi@2 (glm2):\r\n Cmd (0xbdbd20) dump for Target 12 Lun 0:\r\nscsi: [ID 365881 kern.info] /pci@1f,4000/scsi@2 (glm2):\r\n cdb=[ 0x12 0x0 0x0 0x0 0x30 0x0 ]\r\nscsi: [ID 365881 kern.info] /pci@1f,4000/scsi@2 (glm2):\r\n pkt_flags=0x808 pkt_statistics=0x60 pkt_state=0x7\r\nscsi: [ID 365881 kern.info] /pci@1f,4000/scsi@2 (glm2):\r\n pkt_scbp=0x0 cmd_flags=0x2860\r\nscsi: [ID 107833 kern.warning] WARNING: /pci@1f,4000/scsi@2 (glm2):\r\n Connected command timeout for Target 12.0\r\ngenunix: [ID 408822 kern.info] NOTICE: glm2: fault detected in device; service still available\r\ngenunix: [ID 611667 kern.info] NOTICE: glm2: Connected command timeout for Target 12.0\r\nglm: [ID 280919 kern.warning] WARNING: ID[SUNWpd.glm.cmd_timeout.6017]\r\nscsi: [ID 107833 kern.warning] WARNING: /pci@1f,4000/scsi@2 (glm2):\r\n got SCSI bus reset\r\ngenunix: [ID 408822 kern.info] NOTICE: glm2: fault detected in device; service still available\r\ngenunix: [ID 611667 kern.info] NOTICE: glm2: got SCSI bus reset\r\nscsi: [ID 365881 kern.info] /pci@1f,4000/scsi@2 (glm2):\r\n Cmd (0xbdbd20) dump for Target 12 Lun 0:\r\nscsi: [ID 365881 kern.info] /pci@1f,4000/scsi@2 (glm2):\r\n cdb=[ 0x12 0x0 0x0 0x0 0x30 0x0 ]\r\nscsi: [ID 365881 kern.info] /pci@1f,4000/scsi@2 (glm2):\r\n pkt_flags=0x808 pkt_statistics=0x60 pkt_state=0x7\r\nscsi: [ID 365881 kern.info] /pci@1f,4000/scsi@2 (glm2):\r\n pkt_scbp=0x0 cmd_flags=0x2860\r\nscsi: [ID 107833 kern.warning] WARNING: /pci@1f,4000/scsi@2 (glm2):\r\n Connected command timeout for Target 12.0\r\ngenunix: [ID 408822 kern.info] NOTICE: glm2: fault detected in device; service still available\r\ngenunix: [ID 611667 kern.info] NOTICE: glm2: Connected command timeout for Target 12.0\r\nglm: [ID 280919 kern.warning] WARNING: ID[SUNWpd.glm.cmd_timeout.6017]\r\nscsi: [ID 107833 kern.warning] WARNING: /pci@1f,4000/scsi@2 (glm2):\r\n got SCSI bus reset\r\ngenunix: [ID 408822 kern.info] NOTICE: glm2: fault detected in device; service still available\r\ngenunix: [ID 611667 kern.info] NOTICE: glm2: got SCSI bus reset\r\nswapgeneric: [ID 308332 kern.info] root on /pci@1f,4000/scsi@3/disk@0,0:a fstype ufs\r\nkrtld: [ID 469452 kern.info] NOTICE: sf: 64-bit driver module not found\r\nlast message repeated 1 time\r\npcipsy: [ID 370704 kern.info] PCI-device: ebus@1, ebus0\r\ngenunix: [ID 936769 kern.info] ebus0 is /pci@1f,4000/ebus@1\r\nebus: [ID 521012 kern.info] envctrltwo0 at ebus0: offset 14,600000\r\ngenunix: [ID 936769 kern.info] envctrltwo0 is /pci@1f,4000/ebus@1/SUNW,envctrltwo@14,600000\r\nebus: [ID 521012 kern.info] su0 at ebus0: offset 14,3083f8\r\ngenunix: [ID 936769 kern.info] su0 is /pci@1f,4000/ebus@1/su@14,3083f8\r\nebus: [ID 521012 kern.info] su1 at ebus0: offset 14,3062f8\r\ngenunix: [ID 936769 kern.info] su1 is /pci@1f,4000/ebus@1/su@14,3062f8\r\npcipsy: [ID 370704 kern.info] PCI-device: TSI,gfxp@1, gfxp0\r\ngenunix: [ID 936769 kern.info] gfxp0 is /pci@1f,2000/TSI,gfxp@1\r\ngfxp: [ID 722914 kern.notice] TSI: gfxp0 is GFX8P @ 640x480\r\nunix: [ID 987524 kern.info] cpu0: SUNW,UltraSPARC-II (upaid 0 impl 0x11 ver 0xa0 clock 400 MHz)\r\nebus: [ID 521012 kern.info] se0 at ebus0: offset 14,400000\r\ngenunix: [ID 936769 kern.info] se0 is /pci@1f,4000/ebus@1/se@14,400000\r\nebus: [ID 521012 kern.info] se1 at ebus0: offset 14,200000\r\ngenunix: [ID 936769 kern.info] se1 is /pci@1f,4000/ebus@1/se@14,200000\r\nhme: [ID 517527 kern.info] SUNW,hme0 : PCI IO 2.0 (Rev Id = c1) Found\r\npcipsy: [ID 370704 kern.info] PCI-device: network@1,1, hme0\r\ngenunix: [ID 936769 kern.info] hme0 is /pci@1f,4000/network@1,1\r\ngenunix: [ID 454863 kern.info] dump on /dev/dsk/c0t0d0s1 size 2001 MB\r\nhme: [ID 517527 kern.info] SUNW,hme0 : Internal Transceiver Selected.\r\nhme: [ID 517527 kern.info] SUNW,hme0 : 10 Mbps Half-Duplex Link Up\r\npseudo: [ID 129642 kern.info] pseudo-device: devinfo0\r\ngenunix: [ID 936769 kern.info] devinfo0 is /pseudo/devinfo@0\r\npseudo: [ID 129642 kern.info] pseudo-device: tod0\r\ngenunix: [ID 936769 kern.info] tod0 is /pseudo/tod@0\r\npseudo: [ID 129642 kern.info] pseudo-device: pm0\r\ngenunix: [ID 936769 kern.info] pm0 is /pseudo/pm@0\r\nThere are no devices (controllers) in the system; nvutil terminated.\r\nThere are no devices (controllers) in the system.\r\n\r\nfwutil failed!\r\nArray Monitor initiated\r\n/usr/lib/osa/bin/arraymon: [ID 712306 user.error] No RAID devices found to check.\r\nRDAC daemons initiated\r\nrdriver: [ID 400281 kern.notice] ID[RAIDarray.rdaemon.1001] RDAC Resolution Daemon locked in memory\r\npseudo: [ID 129642 kern.info] pseudo-device: vol0\r\ngenunix: [ID 936769 kern.info] vol0 is /pseudo/vol@0\r\nebus: [ID 521012 kern.info] se0 at ebus0: offset 14,400000\r\ngenunix: [ID 936769 kern.info] se0 is /pci@1f,4000/ebus@1/se@14,400000\r\nebus: [ID 521012 kern.info] se1 at ebus0: offset 14,200000\r\ngenunix: [ID 936769 kern.info] se1 is /pci@1f,4000/ebus@1/se@14,200000\r\npseudo: [ID 129642 kern.info] pseudo-device: pm0\r\ngenunix: [ID 936769 kern.info] pm0 is /pseudo/pm@0\r\n\r\n\r\n搞了两天了，还没有什么结果，希望大家帮帮忙，谢谢各位啦。