全双工与半双工

dnfszbd

请大家告诉我下面两台路由器是不是用了相同的工作模式。我只知道3640是全双工，但不知道2600是什么，还是他采用默然的工作模式？？？\r\n3640\r\nPassword:\r\nR_INMS_KEL>;enable\r\nPassword:\r\nR_INMS_KEL#show interface\r\nEthernet0/0 is up, line protocol is up\r\n& Hardware is AmdP2, address is 0008.2175.eec0 (bia 0008.2175.eec0)\r\n& Internet address is 192.168.196.253/24\r\n& MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec,\r\n&&&& reliability 253/255, txload 1/255, rxload 3/255\r\n& Encapsulation ARPA, loopback not set\r\n& Keepalive set (10 sec)\r\n& ARP type: ARPA, ARP Timeout 04:00:00\r\n& Last input 00:00:03, output 00:00:00, output hang never\r\n& Last clearing of \"show interface\" counters 2w2d\r\n& Queueing strategy: fifo\r\n& Output queue 0/40, 0 drops; input queue 0/75, 0 drops\r\n& 5 minute input rate 155000 bits/sec, 52 packets/sec\r\n& 5 minute output rate 17000 bits/sec, 35 packets/sec\r\n&&&& 70644331 packets input, 1246023953 bytes, 0 no buffer\r\n&&&& Received 83786 broadcasts, 0 runts, 0 giants, 0 throttles\r\n&&&& 980164 input errors, 980164 CRC, 858441 frame, 0 overrun, 0 ignored\r\n&&&& 0 input packets with dribble condition detected\r\n&&&& 39058674 packets output, 2485416406 bytes, 0 underruns\r\n&&&& 0 output errors, 0 collisions, 0 interface resets\r\n&&&& 0 babbles, 0 late collision, 0 deferred\r\n&&&& 0 lost carrier, 0 no carrier\r\n&&&& 0 output buffer failures, 0 output buffers swapped out\r\n\r\n2600\r\n\r\nR_INMS_KEL#show interface\r\nEthernet0/0 is up, line protocol is up\r\n  Hardware is AmdP2, address is 0008.2175.eec0 (bia 0008.2175.eec0)\r\n  Internet address is 192.168.196.253/24\r\n  MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec,\r\n     reliability 253/255, txload 1/255, rxload 3/255\r\n  Encapsulation ARPA, loopback not set\r\n  Keepalive set (10 sec)\r\n  ARP type: ARPA, ARP Timeout 04:00:00\r\n  Last input 00:00:03, output 00:00:00, output hang never\r\n  Last clearing of \"show interface\" counters 2w2d\r\n  Queueing strategy: fifo\r\n  Output queue 0/40, 0 drops; input queue 0/75, 0 drops\r\n  5 minute input rate 155000 bits/sec, 52 packets/sec\r\n  5 minute output rate 17000 bits/sec, 35 packets/sec\r\n     70644331 packets input, 1246023953 bytes, 0 no buffer\r\n     Received 83786 broadcasts, 0 runts, 0 giants, 0 throttles\r\n     980164 input errors, 980164 CRC, 858441 frame, 0 overrun, 0 ignored\r\n     0 input packets with dribble condition detected\r\n     39058674 packets output, 2485416406 bytes, 0 underruns\r\n     0 output errors, 0 collisions, 0 interface resets\r\n     0 babbles, 0 late collision, 0 deferred\r\n     0 lost carrier, 0 no carrier\r\n     0 output buffer failures, 0 output buffers swapped out

dnfszbd

应该是这个\r\nPassword:\r\nR_INMS_WLMQ#show interface\r\nFastEthernet0/0 is up, line protocol is up\r\n& Hardware is AmdFE, address is 0007.eb48.f340 (bia 0007.eb48.f340)\r\n& Internet address is 192.192.192.254/24\r\n& MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,\r\n&&&& reliability 255/255, txload 1/255, rxload 1/255\r\n& Encapsulation ARPA, loopback not set\r\n& Keepalive set (10 sec)\r\n& Full-duplex, 100Mb/s, 100BaseTX/FX\r\n& ARP type: ARPA, ARP Timeout 04:00:00\r\n& Last input 00:00:00, output 00:00:00, output hang never\r\n& Last clearing of \"show interface\" counters never\r\n& Queueing strategy: fifo\r\n& Output queue 0/40, 0 drops; input queue 2/75, 11311750 drops\r\n& 5 minute input rate 343000 bits/sec, 223 packets/sec\r\n& 5 minute output rate 521000 bits/sec, 186 packets/sec\r\n&&&& 3034262403 packets input, 3243525806 bytes\r\n&&&& Received 271398218 broadcasts, 0 runts, 0 giants, 0 throttles\r\n&&&& 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored\r\n&&&& 0 watchdog, 0 multicast\r\n&&&& 0 input packets with dribble condition detected\r\n&&&& 6832327 packets output, 678491584 bytes, 0 underruns\r\n&&&& 0 output errors, 0 collisions, 1 interface resets\r\n&&&& 0 babbles, 0 late collision, 600048 deferred\r\n&&&& 0 lost carrier, 0 no carrier\r\n&&&& 0 output buffer failures, 0 output buffers swapped out

dnfszbd

兄弟们帮我看看这两个的工作模式了，拜托！

cnadl

原帖由 \"dnfszbd\" 发表：\n\r\n& Encapsulation ARPA, loopback not set \r\n& Keepalive set (10 sec) \r\n& Full-duplex, 100Mb/s, 100BaseTX/FX \r\n& ARP type: ARPA, ARP Timeout 04:00:00 \r\n& Last input 00:00:00, output 00:00:00, output hang never\r\n

\r\n\r\nethernet口则全为半双工

dnfszbd

3640\r\nR_INMS_WLMQ#show interface\r\n     ...\r\n     ...\r\nEncapsulation ARPA, loopback not set\r\n  Keepalive set (10 sec)\r\n  Full-duplex, 100Mb/s, 100BaseTX/FX\r\n  ARP type: ARPA, ARP Timeout 04:00:00\r\n  Last input 00:00:00, output 00:00:00, output hang never\r\n  Last clearing of \"show interface\" counters never\r\n\r\n2600\r\nR_INMS_KEL#show interface\r\n      .......\r\n      ......\r\nEncapsulation ARPA, loopback not set\r\n  Keepalive set (10 sec)\r\n  ARP type: ARPA, ARP Timeout 04:00:00\r\n  Last input 00:00:03, output 00:00:00, output hang never\r\n  Last clearing of \"show interface\" counters 2w2d\r\n\r\n兄弟还要请教一下，也就是我的3640是全半双工模式工作的对吗，那我的2600  是怎么样的工作模式工作的了，因为现在这两个地方出现数据传输不稳定有丢失的现象怀疑可能就是因为这两台的工作模式不一样导致的

cnadl

ethernet口则全为半双工\r\n\r\n如果担心是双工问题，可以在36上指定。

dnfszbd

cnadl      \r\n天使\r\n\r\nFull-duplex, 100Mb/s, 100BaseTX/FX \r\n\r\nethernet口则全为半双工\r\n\r\n你是不是写错了啊，这个是全双工才对吧