- 论坛徽章:
- 0
|
回复 2楼 SunGod 的帖子
肯定是加了的!!!
郁闷死了……整整搞了一天,找不着原因……
DEBUG信息如下:
---------------------------------------------
* The following section contains information about your system
Fri Nov 18 05:52:18 UTC 2005
Output of uname -a
---------------------------------------------
* The following section contains information about your network
* interfaces. The one you chose for PPPoE should contain the words:
* 'UP' and 'RUNNING'. If it does not, you probably have an Ethernet
* driver problem.
Output of ifconfig -a
eth0 Link encap:Ethernet HWaddr 00:E0:4C:E8:09:4F
inet addr:88.88.88.44 Bcast:88.88.88.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
Interrupt:12 Base address:0xb000
eth1 Link encap:Ethernet HWaddr 00:E0:4C:E9:03:89
inet addr:192.168.0.10 Bcast:192.168.0.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
Interrupt:11 Base address:0xd000
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
---------------------------------------------
* The following section lists your routing table.
* If you have an entry which starts with '0.0.0.0', you probably
* have defined a default route and gateway, and pppd will
* not create a default route using your ISP. Try getting
* rid of this route.
Output of netstat -n -r
---------------------------------------------
Contents of /etc/resolv.conf
* The following section lists DNS setup.
* If you can browse by IP address, but not name, suspect
* a DNS problem.
---------------------------------------------
* The following section lists /etc/ppp/options.
* You should have NOTHING in that file.
Contents of /etc/ppp/options
---------------------------------------------
* The following section identifies your Ethernet interface
* and user name. Some ISP's need 'username'; others
* need 'username@isp.com'. Try both
ETH=eth0; USER=test
---------------------------------------------
* The following section shows the pppd command we will invoke
pppd invocation
/usr/sbin/pppd pty '/usr/sbin/pppoe -p /var/run/pppoe.conf-adsl.pid.pppoe -I eth0 -T 80 -U -m 1412 -S dddd ' noipdefault noauth default-asyncmap defaultroute hide-password nodetach mtu 1492 mru 1492 noaccomp nodeflate nopcomp novj novjccomp user test lcp-echo-interval 20 lcp-echo-failure 3 debug
---------------------------------------------
Couldn't allocate pseudo-tty
---------------------------------------------*
The following section is an extract from your log.
* Look for error messages from pppd, such as
* a lack of kernel support for PPP, authentication failure
* etc.
Extract from /var/log/messages
Fri Nov 18 05:52:18 UTC 2005
---------------------------------------------
* The following section is a dump of the packets
* sent and received by rp-pppoe. If you don't see
* any output, it's an Ethernet driver problem. If you only
* see three PADI packets and nothing else, check your cables
* and modem. Make sure the modem lights flash when you try
* to connect. Check that your Ethernet card is in
* half-duplex, 10Mb/s mode. If all else fails,
* try using pppoe-sniff.
rp-pppoe debugging dump
[ 本帖最后由 独孤九贱 于 2005-11-18 15:59 编辑 ] |
|