Chinaunix

标题: 机器上接了一个scsi硬盘盒我要怎么才能找到？ [打印本页]

作者: luotianshou 时间: 2008-07-05 18:11
标题: 机器上接了一个scsi硬盘盒我要怎么才能找到？
是170的机器

通过lscfg可以看到

# lscfg
INSTALLED RESOURCE LIST
The following resources are installed on the machine.
+/- = Added or deleted from Resource List.
* = Diagnostic support not available.

  Model Architecture: chrp
  Model Implementation: Uni-Processor, PCI bus

+ sys0                      System Object
+ sysplanar0                System Planar
* pci1          P1       PCI Bus
* pci0          P1       PCI Bus
* isa0          P1       ISA Bus
+ fda0          P1/D1    Standard I/O Diskette Adapter
* siokma0       P1/K1    Keyboard/Mouse Adapter
+ sioka0          P1/K1    Keyboard Adapter
+ kbd0          P1-K1    PS/2 keyboard
+ sioma0          P1/K1    Mouse Adapter
+ mouse0          P1-O1    3 button mouse
+ siota0          P1/Q1    Tablet Adapter
+ paud0          P1/Q2    Ultimedia Integrated Audio
+ ppa0          P1/R1    CHRP IEEE1284 (ECP) Parallel Port Adapter
+ sa0             P1/S1    Standard I/O Serial Port
+ sa1             P1/S2    Standard I/O Serial Port
+ scsi0          P1/Z1    Wide/Ultra-2 SCSI I/O Controller
+ cd0             P1/Z1-A1  16 Bit SCSI Multimedia CD-ROM Drive (650 MB)
+ hdisk0          P1/Z1-A2  16 Bit LVD SCSI Disk Drive (18200 MB)
+ rmt0          P1/Z1-A5  SCSI 4mm Tape Drive (12000 MB)
+ hdisk1          P1/Z1-A6  16 Bit LVD SCSI Disk Drive (18200 MB)
+ scsi1          P1/Z2    Wide/Ultra-2 SCSI I/O Controller
+ ent1          P1-I3/E1  IBM 10/100 Mbps Ethernet PCI Adapter (23100020)
+ mg20          P1-I5/G1  GXT130P Graphics Adapter
+ ent0          P1/E1    IBM 10/100 Mbps Ethernet PCI Adapter (23100020)
+ L2cache0                L2 Cache
+ mem0                      Memory
+ proc0          P1-C1    Processor

我要怎么才能找到硬盘盒里面的硬盘呢？

作者: jaix 时间: 2008-07-05 19:56
#cfgmgr -v

作者: luotianshou 时间: 2008-07-06 17:02
标题: 回复 #2 jaix 的帖子
#cfgmgr -v

我用了这个命令然后lspv 还是找不到呢

作者: jaix 时间: 2008-07-06 20:15
From your #lscfg output,I find your 170 only have self inner scsi device (scsi0 scsi1),
+ scsi0          P1/Z1    Wide/Ultra-2 SCSI I/O Controller
+ scsi1          P1/Z2    Wide/Ultra-2 SCSI I/O Controller

and your hdisk0 and hdisk1 are connected to the scsi0.
+ hdisk0          P1/Z1-A2  16 Bit LVD SCSI Disk Drive (18200 MB)
+ hdisk1          P1/Z1-A6  16 Bit LVD SCSI Disk Drive (18200 MB)

do you connect the disk box to the scsi1 which port is on the back of 170 ?
please use command :
#cfgmgr -l scsi1

if you can't configure out the new disk in the box,
please check your scsi cable and disk box,
Maybe one of them is bad.

作者: luotianshou 时间: 2008-07-08 14:57
标题: 回复 #4 jaix 的帖子
我是连接到170自带的scsi卡上的。

连上后运行cfgmgr（cfgmgr -l scsi1也用了）,然后lsdev -Cc disk还是只能发现hdisk0 hdisk1

scsi id 没有冲突。

线缆也是2条都试了。。还是找不到。

难道盒子是坏的？

作者: chalylau 时间: 2008-07-08 15:18

原帖由 luotianshou 于 2008-7-8 14:57 发表
我是连接到170自带的scsi卡上的。

连上后运行cfgmgr（cfgmgr -l scsi1也用了）,然后lsdev -Cc disk还是只能发现hdisk0 hdisk1

scsi id 没有冲突。

线缆也是2条都试了。。还是找不到。

难道盒子是坏的？

硬盘盒需要加电吗？

作者: jaix 时间: 2008-07-08 15:33
From your #lscfg output,
can't find any other scsi port,
scsi0 and scsi1 are your system self port,

check your scsi adapter,it didn't been configure on your system.

作者: zlwww1227 时间: 2008-07-08 17:32
提示: 作者被禁止或删除内容自动屏蔽

作者: luotianshou 时间: 2008-07-08 17:56
标题: 回复 #7 jaix 的帖子
硬盘盒需要加电。电源肯定是开了的。

# lsdev
L2cache0 Available             L2 Cache
aio0    Defined                Asynchronous I/O (Legacy)
cd0       Available 10-60-00-1,0  16 Bit SCSI Multimedia CD-ROM Drive
en0       Defined 10-80       Standard Ethernet Network Interface
en1       Available 10-68       Standard Ethernet Network Interface
ent0    Available 10-80       IBM 10/100 Mbps Ethernet PCI Adapter (23100020)
ent1    Available 10-68       IBM 10/100 Mbps Ethernet PCI Adapter (23100020)
et0       Defined 10-80       IEEE 802.3 Ethernet Network Interface
et1       Defined 10-68       IEEE 802.3 Ethernet Network Interface
fd0       Available 01-D1-00-00 Diskette Drive
fda0    Available 01-D1       Standard I/O Diskette Adapter
gxme0    Defined                Graphics Data Transfer Assist Subsystem
hd1       Defined                Logical volume
hd2       Defined                Logical volume
hd3       Defined                Logical volume
hd4       Defined                Logical volume
hd5       Defined                Logical volume
hd6       Defined                Logical volume
hd8       Defined                Logical volume
hd10opt Defined                Logical volume
hd9var    Defined                Logical volume
hdisk0    Available 10-60-00-0,0  16 Bit LVD SCSI Disk Drive
hdisk1    Available 10-60-00-8,0  16 Bit LVD SCSI Disk Drive
inet0    Available             Internet Network Extension
isa0    Available 10-58       ISA Bus
iscsi0    Available             iSCSI Protocol Device
kbd0    Defined 01-K1-00-00 PS/2 keyboard
lft0    Available             Low Function Terminal Subsystem
lo0       Available             Loopback Network Interface
lvdd    Available             LVM Device Driver
mem0    Available             Memory
mg20    Defined 10-78       GXT130P Graphics Adapter
mg21    Available 10-88       GXT130P Graphics Adapter
mouse0    Defined 01-K1-01-00 3 button mouse
paud0    Available 01-Q2       Ultimedia Integrated Audio
pci0    Available             PCI Bus
pci1    Available             PCI Bus
posix_aio0 Defined                Posix Asynchronous I/O
ppa0    Available 01-R1       CHRP IEEE1284 (ECP) Parallel Port Adapter
proc0    Available 00-00       Processor
pty0    Available             Asynchronous Pseudo-Terminal
rcm0    Available             Rendering Context Manager Subsystem
rmt0    Available 10-60-00-5,0  SCSI 4mm Tape Drive
rootvg    Defined                Volume group
sa0       Available 01-S1       Standard I/O Serial Port
sa1       Available 01-S2       Standard I/O Serial Port
scsi0    Available 10-60       Wide/Ultra-2 SCSI I/O Controller
scsi1    Available 10-61       Wide/Ultra-2 SCSI I/O Controller
sioka0    Available 01-K1-00    Keyboard Adapter
siokma0 Available 01-K1       Keyboard/Mouse Adapter
sioma0    Available 01-K1-01    Mouse Adapter
siota0    Available 01-Q1       Tablet Adapter
sys0    Available             System Object
sysplanar0 Available             System Planar
tmscsi0 Defined 10-61-00-0,0  Other SCSI Initiator Device
tmscsi1 Defined 10-61-00-0,1  Other SCSI Initiator Device
tmscsi2 Defined 10-61-00-1,0  Other SCSI Initiator Device
tmscsi3 Defined 10-61-00-1,1  Other SCSI Initiator Device
tmscsi4 Defined 10-61-00-3,0  Other SCSI Initiator Device
tmscsi5 Defined 10-61-00-3,1  Other SCSI Initiator Device
tmscsi6 Defined 10-61-00-4,0  Other SCSI Initiator Device
tmscsi7 Defined 10-61-00-4,1  Other SCSI Initiator Device
tmscsi8 Defined 10-61-00-5,0  Other SCSI Initiator Device
tmscsi9 Defined 10-61-00-5,1  Other SCSI Initiator Device
tmscsi10 Defined 10-61-00-6,0  Other SCSI Initiator Device
tmscsi11 Defined 10-61-00-6,1  Other SCSI Initiator Device
tmscsi12 Defined 10-61-00-8,0  Other SCSI Initiator Device
tmscsi13 Defined 10-61-00-8,1  Other SCSI Initiator Device
tmscsi14 Defined 10-61-00-9,0  Other SCSI Initiator Device
tmscsi15 Defined 10-61-00-9,1  Other SCSI Initiator Device
tmscsi16 Defined 10-61-00-10,0 Other SCSI Initiator Device
tmscsi17 Defined 10-61-00-10,1 Other SCSI Initiator Device
tmscsi18 Defined 10-61-00-11,0 Other SCSI Initiator Device
tmscsi19 Defined 10-61-00-11,1 Other SCSI Initiator Device
tmscsi20 Defined 10-61-00-7,0  SCSI I/O Controller Initiator Device

用lsdev就发现这些

scsi0 and scsi1 are your system self port,

那连接盒子的端口用那个命令能够看到？

我是连接到机器自带的SCSI口

[ 本帖最后由 luotianshou 于 2008-7-8 18:06 编辑 ]

作者: jaix 时间: 2008-07-08 18:34
#lsdev -C |grep scsi
iscsi0    Available             iSCSI Protocol Device
scsi0    Available 10-60       Wide/Ultra-2 SCSI I/O Controller
scsi1    Available 10-61       Wide/Ultra-2 SCSI I/O Controller
scsi2    Available 20-58-00    Ultra320 SCSI RAID Adapter Physical bus
scsi3    Available 20-58-01    Ultra320 SCSI RAID Adapter Physical bus

if your system can configure the scsi adapter well,you can see the scsi2 or scsi3.

作者: jaix 时间: 2008-07-08 18:36
the cause maybe your scsi card is bad.

作者: luotianshou 时间: 2008-07-08 23:27
标题: 回复 #11 jaix 的帖子
谢谢你的回复。

我用的试验机是44- 170 自带的scsi接口。

我有2台机器，2根线缆。但是都还是不能找到硬盘盒。

难道2台的scsi接口都坏了？

我想得重找一个盒子来试试。。。

估计盒子出问题的几率大一些吧？

千万别scsi接口是坏的，那样就麻烦了。

那目前的情况可以判断2种可能，是吧？

1可能是scsi接口坏了

2可能是硬盘盒子是有问题的？

[ 本帖最后由 luotianshou 于 2008-7-8 23:29 编辑 ]

作者: chalylau 时间: 2008-07-08 23:59

1可能是scsi接口坏了

2可能是硬盘盒子是有问题的？

看下来只有这2种可能了

欢迎光临 Chinaunix (http://bbs.chinaunix.net/)