Chinaunix
标题:
求助高手:VA7110更换一块硬盘执行rbld成功后此硬盘状态仍为Previously Used是否正常
[打印本页]
作者:
dong_root
时间:
2012-06-27 10:31
标题:
求助高手:VA7110更换一块硬盘执行rbld成功后此硬盘状态仍为Previously Used是否正常
本帖最后由 dong_root 于 2012-06-27 10:33 编辑
1、环境:一台HP rp4440安装的B.11.11,主机上没有安装SDM软件,无法通过系统管理VA7110,只能通过串口的方式管理。(尝试安装SDM,但因为是在线系统,牵涉到JRE的相关东西,无法更改,所以安装SDM的想法是行不通了。)VA7110共有10块硬盘,做的raid1.
2、问题:
前几日发现第8块硬盘黄灯告警,采购到配件以后进行了更换,在更换过硬盘后大概20秒,告警灯就消失了。
信息如下:
Warning State > dsp -d
DISK AT M/D1:
Drive State: Included
Vendor ID: HP 73.4G
Product ID: ST373307FC
Product Revision: HP05
Capacity: 68096 MB
Loop Address: 111
Node WWN: 0x2000000c505aabf5
Initialization State: Ready
Volume Set Serial No: 000029B500000004
Block Size: 520
Serial Number: 3HZ60M26
DISK AT M/D2:
Drive State: Included
Vendor ID: HP 73.4G
Product ID: ST373307FC
Product Revision: HP05
Capacity: 68096 MB
Loop Address: 112
Node WWN: 0x2000000c505ab5b0
Initialization State: Ready
Volume Set Serial No: 000029B500000004
Block Size: 520
Serial Number: 3HZ60Z2W
Recovery Maps are on this disk.
DISK AT M/D3:
Drive State: Included
Vendor ID: HP 73.4G
Product ID: ST373405FC
Product Revision: HP09
Capacity: 68096 MB
Loop Address: 113
Node WWN: 0x20000004cf6b2bac
Initialization State: Ready
Volume Set Serial No: 000029B500000004
Block Size: 520
Serial Number: 3EK0ZA30
DISK AT M/D4:
Drive State: Included
Vendor ID: HP 73.4G
Product ID: ST373307FC
Product Revision: HP05
Capacity: 68096 MB
Loop Address: 114
Node WWN: 0x20000004cf30ca99
Initialization State: Ready
Volume Set Serial No: 000029B500000004
Block Size: 520
Serial Number: 3HZ0NGW5
Recovery Maps are on this disk.
DISK AT M/D5:
Drive State: Included
Vendor ID: HP 73.4G
Product ID: ST373405FC
Product Revision: HP0A
Capacity: 68096 MB
Loop Address: 115
Node WWN: 0x20000004cf5ee0db
Initialization State: Ready
Volume Set Serial No: 000029B500000004
Block Size: 520
Serial Number: 3EK1FVY9
DISK AT M/D6:
Drive State: Included
Vendor ID: HP 73.4G
Product ID: ST373405FC
Product Revision: HP0A
Capacity: 68096 MB
Loop Address: 116
Node WWN: 0x2000001862fcff50
Initialization State: Ready
Volume Set Serial No: 000029B500000004
Block Size: 520
Serial Number: 3EK2PL49
DISK AT M/D7:
Drive State: Included
Vendor ID: HP 73.4G
Product ID: ST373307FC
Product Revision: HP05
Capacity: 68096 MB
Loop Address: 117
Node WWN: 0x2000000c5025d75f
Initialization State: Ready
Volume Set Serial No: 000029B500000004
Block Size: 520
Serial Number: 3HZ1AJHR
DISK AT M/D8:
Drive State: Previously Used
Vendor ID: HP 73.4G
Product ID: ST373307FC
Product Revision: HP03
Capacity: 68096 MB
Loop Address: 118
Node WWN: 0x2000000c50a70b50
Initialization State: Ready
Volume Set Serial No: 0000CE0C00000009
Block Size: 520
Serial Number: 3HZ6T6C0
Recovery Maps are on this disk.
DISK AT M/D9:
Drive State: Included
Vendor ID: HPQ
Product ID: BD1465822C
Product Revision: HP04
Capacity: 136704 MB
Loop Address: 119
Node WWN: 0x20000011c6a7c84c
Initialization State: Ready
Volume Set Serial No: 000029B500000004
Block Size: 520
Serial Number: 3KS0P3JD0000
DISK AT M/D10:
Drive State: Included
Vendor ID: HPQ
Product ID: BD1465822C
Product Revision: HP04
Capacity: 136704 MB
Loop Address: 120
Node WWN: 0x20000014c39dd083
Initialization State: Ready
Volume Set Serial No: 000029B500000004
Block Size: 520
Serial Number: 3KS3XCVK0000
Total capacity of physical disks in array = 799 GB
Warning State > dsp -L
LUN 0:
Capacity: 120.0 GB
Number of Snapshots: 0
RGID: 1
LUN 1:
Capacity: 135.0 GB
Number of Snapshots: 0
RGID: 1
LUN 2:
Capacity: 133.0 GB
Number of Snapshots: 0
RGID: 1
Warning State > dsp -e
Enclosure at M:
Loop Pair: 255
Enclosure ID: 0
Enclosure Status: OK
Enclosure Type: MAIN
Serial Number: 0x00USR000037L
Warning State > dsp -f
FRU LOCATION HARDWARE COMPONENT IDENTIFICATION STATUS
=========================================================================
M Main Enclosure 00USR000037L Warning State
M/C1 AutoRaid Controller 1 00PR00D10677 Good
M/C2 AutoRaid Controller 2 00PR00D10340 Good
M/C1.B1 NVRAM Battery 000000000054 Good
M/C2.B1 NVRAM Battery 000000042490 Good
M/C1.M1 Memory DIMM Not Applicable Good
M/C2.M1 Memory DIMM Not Applicable Good
M/C1.H1 Host Port1 0x50060b00001b78c6 Good
M/C2.H1 Host Port1 0x50060b00001b75a6 Good
M/D1 Disk 1 3HZ60M26 Included
M/D2 Disk 2 3HZ60Z2W Included
M/D3 Disk 3 3EK0ZA30 Included
M/D4 Disk 4 3HZ0NGW5 Included
M/D5 Disk 5 3EK1FVY9 Included
M/D6 Disk 6 3EK2PL49 Included
M/D7 Disk 7 3HZ1AJHR Included
M/D8 Disk 8 3HZ6T6C0 Previously Used
M/D9 Disk 9 3KS0P3JD0000 Included
M/D10 Disk 10 3KS3XCVK0000 Included
Warning State > dsp -s
SUBSYSTEM SETTINGS:
Capacity Depletion Threshold: 0
Subsystem Level RAID Control: RAID 1
Enable Manual Override: FALSE
Manual Override Destination: FALSE
Enable Optimize Policy: TRUE
Read Cache Disable: FALSE
Write Cache Enable: FALSE
Enable Prefetch: TRUE
Rebuild Priority: LOW
Unit Attention: TRUE
Disabl Sec Path Presentation: FALSE
Volume Set Partitioning: FALSE
Write Working Set Interval: 0x21C0
RESILIENCY SETTINGS
Enable Secure Mode: TRUE
Disable NVRAM on UPS Absent: FALSE
Disable NVRAM on WCE False: FALSE
Disable Read Hits: FALSE
Force Unit Access Response: 1
Lock Write Cache On: TRUE
Resiliency Threshold: 4 s
Single Controller Warning: TRUE
DISK SETTINGS
Auto Include: TRUE
Auto Rebuild: TRUE
Hot Spare Mode: Automatic
Max Drives per Subsystem: 45
LUN SETTINGS
LUN Creation Limit: 1024
Maximum LUN Creation Limit: 1024
Migrating Write Destination: FALSE
Security Enabled: FALSE
PORT SETTINGS
Controller 1 Host Port1
Loop ID: 110
Link Topology: Private Loop
OS Behavior: HP-UX
Port WWN: 0x50060b00001b78c6
Queue Full Threshold: 750
Data Rate: 2 GB/sec
Controller 1 JBOD Port1
Data Rate: 2 GB/sec
Controller 2 Host Port1
Loop ID: 118
Link Topology: Private Loop
OS Behavior: HP-UX
Port WWN: 0x50060b00001b75a6
Queue Full Threshold: 750
Data Rate: 2 GB/sec
Controller 2 JBOD Port1
Data Rate: 2 GB/sec
STATUS
Subsystem State: 1
WARNINGS
Hot Spare Unavailable
Capacity Depletion
Warning State > dsp -c
CONTROLLER AT M/C1
Controller State: Good
Serial Number: 00PR00D10677
Vendor ID: HP
Product ID: A6189B
Product Revision: A120
Battery Charger FW Revision: 5.0
HOST PORT1 INFORMATION
Status: Good
Host OS: HPUX
Port WWN: 0x50060b00001b78c6
Link State: Up
Port Data Rate: 2 GB/sec
Queue Full Threshold: 750
Topology: Private Loop
Loop ID: 110
JBOD PORT1 INFORMATION
Status: Good
Link State: Up
Port Data Rate: 2 GB/sec
-----------------------------------------------------------
CONTROLLER AT M/C2
Controller State: Good
Serial Number: 00PR00D10340
Vendor ID: HP
Product ID: A6189B
Product Revision: A120
Battery Charger FW Revision: 5.0
HOST PORT1 INFORMATION
Status: Good
Host OS: HPUX
Port WWN: 0x50060b00001b75a6
Link State: Up
Port Data Rate: 2 GB/sec
Queue Full Threshold: 750
Topology: Private Loop
Loop ID: 118
JBOD PORT1 INFORMATION
Status: Good
Link State: Up
Port Data Rate: 2 GB/sec
-----------------------------------------------------------
Warning State > recover -s
Volume Set Serial Number: 0000000018001e80
No Recovery in progress.
未完看回复
作者:
dong_root
时间:
2012-06-27 10:32
因为前期查看此磁阵的配置信息是显示自动rbld的,等到第二天连进去一看,发现第8块硬盘的状态:
M/D8 Disk 8 3HZ6T6C0 Previously Used
Warning State > dsp -f
FRU LOCATION HARDWARE COMPONENT IDENTIFICATION STATUS
=========================================================================
M Main Enclosure 00USR000037L Warning State
M/C1 AutoRaid Controller 1 00PR00D10677 Good
M/C2 AutoRaid Controller 2 00PR00D10340 Good
M/C1.B1 NVRAM Battery 000000000054 Good
M/C2.B1 NVRAM Battery 000000042490 Good
M/C1.M1 Memory DIMM Not Applicable Good
M/C2.M1 Memory DIMM Not Applicable Good
M/C1.H1 Host Port1 0x50060b00001b78c6 Good
M/C2.H1 Host Port1 0x50060b00001b75a6 Good
M/D1 Disk 1 3HZ60M26 Included
M/D2 Disk 2 3HZ60Z2W Included
M/D3 Disk 3 3EK0ZA30 Included
M/D4 Disk 4 3HZ0NGW5 Included
M/D5 Disk 5 3EK1FVY9 Included
M/D6 Disk 6 3EK2PL49 Included
M/D7 Disk 7 3HZ1AJHR Included
M/D8 Disk 8 3HZ6T6C0 Previously Used
M/D9 Disk 9 3KS0P3JD0000 Included
M/D10 Disk 10 3KS3XCVK0000 Included
怀疑可能是设备过老,同步进程出了问题,于是又手工执行了一次同步:
Warning State > rbld -a on
Rebuild Enabled.
Warning State > rbld -p
REBUILD STATUS:
Auto Rebuild: Enabled
Rebuild Priority: Low
No rebuild in progress.
Warning State > recover -?
Performs NVRAM recovery operations.
Usage:
recover [-ps <on|off>] [-s] [-?]
-ps: Set parity scan and start recovering process.
-s: Returns the recovery status of the disk array
as well as the status of the recovery progress.
-?: Displays help.
No option: Start recovering process with parity scan.
Warning State > recover -ps on
Volume Set Serial Number: 0000000017fe1688
Attempt to Recover this Volume Set (yes/no)?:
yes
Attempting to reconstruct NVRAM.
This process can take up to several hours.
Use 'vfprecover -s' to view Recovery progress.
No Map > vfpreconver -s
Volume Set Serial Number: 0000000018001e88
Recovery Progress: 0 %
No Map > rbld -p
REBUILD STATUS:
Auto Rebuild: Enabled
Rebuild Priority: Low
No rebuild in progress.
No Map > recover -?
Performs NVRAM recovery operations.
Usage:
recover [-ps <on|off>] [-s] [-?]
-ps: Set parity scan and start recovering process.
-s: Returns the recovery status of the disk array
as well as the status of the recovery progress.
-?: Displays help.
No option: Start recovering process with parity scan.
No Map > recover -s
Volume Set Serial Number: 0000000018001e88
Recovery Progress: 0 %
No Map > dsp -f
FRU LOCATION HARDWARE COMPONENT IDENTIFICATION STATUS
=========================================================================
M Main Enclosure 00USR000037L No Map
M/C1 AutoRaid Controller 1 00PR00D10677 Good
M/C2 AutoRaid Controller 2 00PR00D10340 Good
M/C1.B1 NVRAM Battery 000000000054 Good
M/C2.B1 NVRAM Battery 000000042490 Good
M/C1.M1 Memory DIMM Not Applicable Good
M/C2.M1 Memory DIMM Not Applicable Good
M/C1.H1 Host Port1 0x50060b00001b78c6 Good
M/C2.H1 Host Port1 0x50060b00001b75a6 Good
M/D1 Disk 1 3HZ60M26 Included
M/D2 Disk 2 3HZ60Z2W Included
M/D3 Disk 3 3EK0ZA30 Included
M/D4 Disk 4 3HZ0NGW5 Included
M/D5 Disk 5 3EK1FVY9 Included
M/D6 Disk 6 3EK2PL49 Included
M/D7 Disk 7 3HZ1AJHR Included
M/D8 Disk 8 3HZ6T6C0 Previously Used
M/D9 Disk 9 3KS0P3JD0000 Included
M/D10 Disk 10 3KS3XCVK0000 Included
No Map > dsp -d M/D8
Disk at M/D8:
Drive State: Previously Used
Vendor ID: HP 73.4G
Product ID: ST373307FC
Product Revision: HP03
Capacity: 68096 MB
Loop Address: 118
Node WWN: 0x2000000c50a70b50
Initialization State: Ready
Volume Set Serial No: 0000CE0C00000009
Block Size: 520
Serial Number: 3HZ6T6C0
Recovery Maps are on this disk.
No Map > recover -s
Volume Set Serial Number: 0000000018001e88
Recovery Progress: 1 %
No Map > recover -s
Volume Set Serial Number: 0000000018001e88
Recovery Progress: 2 %
No Map >
No Map > recover -s
Volume Set Serial Number: 0000000018001e88
Recovery Progress: 13 %
No Map >
让它自己同步了,今天早上又过去看,更换的硬盘状态仍然是Previously Used。
Warning State > dsp -s
SUBSYSTEM SETTINGS:
Capacity Depletion Threshold: 0
Subsystem Level RAID Control: RAID 1
Enable Manual Override: FALSE
Manual Override Destination: FALSE
Enable Optimize Policy: TRUE
Read Cache Disable: FALSE
Write Cache Enable: FALSE
Enable Prefetch: TRUE
Rebuild Priority: LOW
Unit Attention: TRUE
Disabl Sec Path Presentation: FALSE
Volume Set Partitioning: FALSE
Write Working Set Interval: 0x21C0
RESILIENCY SETTINGS
Enable Secure Mode: TRUE
Disable NVRAM on UPS Absent: FALSE
Disable NVRAM on WCE False: FALSE
Disable Read Hits: FALSE
Force Unit Access Response: 1
Lock Write Cache On: TRUE
Resiliency Threshold: 4 s
Single Controller Warning: TRUE
DISK SETTINGS
Auto Include: TRUE
Auto Rebuild: TRUE
Hot Spare Mode: Automatic
Max Drives per Subsystem: 45
LUN SETTINGS
LUN Creation Limit: 1024
Maximum LUN Creation Limit: 1024
Migrating Write Destination: FALSE
Security Enabled: FALSE
PORT SETTINGS
Controller 1 Host Port1
Loop ID: 110
Link Topology: Private Loop
OS Behavior: HP-UX
Port WWN: 0x50060b00001b78c6
Queue Full Threshold: 750
Data Rate: 2 GB/sec
Controller 1 JBOD Port1
Data Rate: 2 GB/sec
Controller 2 Host Port1
Loop ID: 118
Link Topology: Private Loop
OS Behavior: HP-UX
Port WWN: 0x50060b00001b75a6
Queue Full Threshold: 750
Data Rate: 2 GB/sec
Controller 2 JBOD Port1
Data Rate: 2 GB/sec
STATUS
Subsystem State: 1
The Subsystem is TESTING.
WARNINGS
Hot Spare Unavailable
Capacity Depletion
Warning State > dsp -f
FRU LOCATION HARDWARE COMPONENT IDENTIFICATION STATUS
=========================================================================
M Main Enclosure 00USR000037L Warning State
M/C1 AutoRaid Controller 1 00PR00D10677 Good
M/C2 AutoRaid Controller 2 00PR00D10340 Good
M/C1.B1 NVRAM Battery 000000000054 Good
M/C2.B1 NVRAM Battery 000000042490 Good
M/C1.M1 Memory DIMM Not Applicable Good
M/C2.M1 Memory DIMM Not Applicable Good
M/C1.H1 Host Port1 0x50060b00001b78c6 Good
M/C2.H1 Host Port1 0x50060b00001b75a6 Good
M/D1 Disk 1 3HZ60M26 Included
M/D2 Disk 2 3HZ60Z2W Included
M/D3 Disk 3 3EK0ZA30 Included
M/D4 Disk 4 3HZ0NGW5 Included
M/D5 Disk 5 3EK1FVY9 Included
M/D6 Disk 6 3EK2PL49 Included
M/D7 Disk 7 3HZ1AJHR Included
M/D8 Disk 8 3HZ6T6C0 Previously Used
M/D9 Disk 9 3KS0P3JD0000 Included
M/D10 Disk 10 3KS3XCVK0000 Included
Warning State > recover -s
Volume Set Serial Number: 0000000018001e80
No Recovery in progress.
Warning State > recover -s
Volume Set Serial Number: 0000000018001e80
No Recovery in progress.
Warning State > dsp -d
DISK AT M/D1:
Drive State: Included
Vendor ID: HP 73.4G
Product ID: ST373307FC
Product Revision: HP05
Capacity: 68096 MB
Loop Address: 111
Node WWN: 0x2000000c505aabf5
Initialization State: Ready
Volume Set Serial No: 000029B500000004
Block Size: 520
Serial Number: 3HZ60M26
DISK AT M/D2:
Drive State: Included
Vendor ID: HP 73.4G
Product ID: ST373307FC
Product Revision: HP05
Capacity: 68096 MB
Loop Address: 112
Node WWN: 0x2000000c505ab5b0
Initialization State: Ready
Volume Set Serial No: 000029B500000004
Block Size: 520
Serial Number: 3HZ60Z2W
Recovery Maps are on this disk.
DISK AT M/D3:
Drive State: Included
Vendor ID: HP 73.4G
Product ID: ST373405FC
Product Revision: HP09
Capacity: 68096 MB
Loop Address: 113
Node WWN: 0x20000004cf6b2bac
Initialization State: Ready
Volume Set Serial No: 000029B500000004
Block Size: 520
Serial Number: 3EK0ZA30
DISK AT M/D4:
Drive State: Included
Vendor ID: HP 73.4G
Product ID: ST373307FC
Product Revision: HP05
Capacity: 68096 MB
Loop Address: 114
Node WWN: 0x20000004cf30ca99
Initialization State: Ready
Volume Set Serial No: 000029B500000004
Block Size: 520
Serial Number: 3HZ0NGW5
Recovery Maps are on this disk.
DISK AT M/D5:
Drive State: Included
Vendor ID: HP 73.4G
Product ID: ST373405FC
Product Revision: HP0A
Capacity: 68096 MB
Loop Address: 115
Node WWN: 0x20000004cf5ee0db
Initialization State: Ready
Volume Set Serial No: 000029B500000004
Block Size: 520
Serial Number: 3EK1FVY9
DISK AT M/D6:
Drive State: Included
Vendor ID: HP 73.4G
Product ID: ST373405FC
Product Revision: HP0A
Capacity: 68096 MB
Loop Address: 116
Node WWN: 0x2000001862fcff50
Initialization State: Ready
Volume Set Serial No: 000029B500000004
Block Size: 520
Serial Number: 3EK2PL49
DISK AT M/D7:
Drive State: Included
Vendor ID: HP 73.4G
Product ID: ST373307FC
Product Revision: HP05
Capacity: 68096 MB
Loop Address: 117
Node WWN: 0x2000000c5025d75f
Initialization State: Ready
Volume Set Serial No: 000029B500000004
Block Size: 520
Serial Number: 3HZ1AJHR
DISK AT M/D8:
Drive State: Previously Used
Vendor ID: HP 73.4G
Product ID: ST373307FC
Product Revision: HP03
Capacity: 68096 MB
Loop Address: 118
Node WWN: 0x2000000c50a70b50
Initialization State: Ready
Volume Set Serial No: 0000CE0C00000009
Block Size: 520
Serial Number: 3HZ6T6C0
Recovery Maps are on this disk.
DISK AT M/D9:
Drive State: Included
Vendor ID: HPQ
Product ID: BD1465822C
Product Revision: HP04
Capacity: 136704 MB
Loop Address: 119
Node WWN: 0x20000011c6a7c84c
Initialization State: Ready
Volume Set Serial No: 000029B500000004
Block Size: 520
Serial Number: 3KS0P3JD0000
DISK AT M/D10:
Drive State: Included
Vendor ID: HPQ
Product ID: BD1465822C
Product Revision: HP04
Capacity: 136704 MB
Loop Address: 120
Node WWN: 0x20000014c39dd083
Initialization State: Ready
Volume Set Serial No: 000029B500000004
Block Size: 520
Serial Number: 3KS3XCVK0000
Total capacity of physical disks in array = 799 GB
Warning State > dsp -e
Enclosure at M:
Loop Pair: 255
Enclosure ID: 0
Enclosure Status: OK
Enclosure Type: MAIN
Serial Number: 0x00USR000037L
Warning State > dsp -a
Invalid option: -a
Warning State > dsp -s
SUBSYSTEM SETTINGS:
Capacity Depletion Threshold: 0
Subsystem Level RAID Control: RAID 1
Enable Manual Override: FALSE
Manual Override Destination: FALSE
Enable Optimize Policy: TRUE
Read Cache Disable: FALSE
Write Cache Enable: FALSE
Enable Prefetch: TRUE
Rebuild Priority: LOW
Unit Attention: TRUE
Disabl Sec Path Presentation: FALSE
Volume Set Partitioning: FALSE
Write Working Set Interval: 0x21C0
RESILIENCY SETTINGS
Enable Secure Mode: TRUE
Disable NVRAM on UPS Absent: FALSE
Disable NVRAM on WCE False: FALSE
Disable Read Hits: FALSE
Force Unit Access Response: 1
Lock Write Cache On: TRUE
Resiliency Threshold: 4 s
Single Controller Warning: TRUE
DISK SETTINGS
Auto Include: TRUE
Auto Rebuild: TRUE
Hot Spare Mode: Automatic
Max Drives per Subsystem: 45
LUN SETTINGS
LUN Creation Limit: 1024
Maximum LUN Creation Limit: 1024
Migrating Write Destination: FALSE
Security Enabled: FALSE
PORT SETTINGS
Controller 1 Host Port1
Loop ID: 110
Link Topology: Private Loop
OS Behavior: HP-UX
Port WWN: 0x50060b00001b78c6
Queue Full Threshold: 750
Data Rate: 2 GB/sec
Controller 1 JBOD Port1
Data Rate: 2 GB/sec
Controller 2 Host Port1
Loop ID: 118
Link Topology: Private Loop
OS Behavior: HP-UX
Port WWN: 0x50060b00001b75a6
Queue Full Threshold: 750
Data Rate: 2 GB/sec
Controller 2 JBOD Port1
Data Rate: 2 GB/sec
STATUS
Subsystem State: 1
The Subsystem is TESTING.
WARNINGS
Hot Spare Unavailable
Capacity Depletion
Warning State > dsp -c
CONTROLLER AT M/C1
Controller State: Good
Serial Number: 00PR00D10677
Vendor ID: HP
Product ID: A6189B
Product Revision: A120
Battery Charger FW Revision: 5.0
HOST PORT1 INFORMATION
Status: Good
Host OS: HPUX
Port WWN: 0x50060b00001b78c6
Link State: Up
Port Data Rate: 2 GB/sec
Queue Full Threshold: 750
Topology: Private Loop
Loop ID: 110
JBOD PORT1 INFORMATION
Status: Good
Link State: Up
Port Data Rate: 2 GB/sec
-----------------------------------------------------------
CONTROLLER AT M/C2
Controller State: Good
Serial Number: 00PR00D10340
Vendor ID: HP
Product ID: A6189B
Product Revision: A120
Battery Charger FW Revision: 5.0
HOST PORT1 INFORMATION
Status: Good
Host OS: HPUX
Port WWN: 0x50060b00001b75a6
Link State: Up
Port Data Rate: 2 GB/sec
Queue Full Threshold: 750
Topology: Private Loop
Loop ID: 118
JBOD PORT1 INFORMATION
Status: Good
Link State: Up
Port Data Rate: 2 GB/sec
-----------------------------------------------------------
Warning State > dsp -e
Enclosure at M:
Loop Pair: 255
Enclosure ID: 0
Enclosure Status: OK
Enclosure Type: MAIN
Serial Number: 0x00USR000037L
Warning State > dsp -L
LUN 0:
Capacity: 120.0 GB
Number of Snapshots: 0
RGID: 1
LUN 1:
Capacity: 135.0 GB
Number of Snapshots: 0
RGID: 1
LUN 2:
Capacity: 133.0 GB
Number of Snapshots: 0
RGID: 1
Warning State > rbld -p
REBUILD STATUS:
Auto Rebuild: Enabled
Rebuild Priority: Low
No rebuild in progress.
请问高手,我这块硬盘的状态显示成Previously Used是不是正常的?怎样解决呀?
作者:
dong_root
时间:
2012-06-27 11:01
HP上说是要用手工加入,但装不了SDM软件,无法执行armcfg 的命令。
作者:
lbseraph
时间:
2012-06-27 17:13
在串口中的话可以用vfpcfg,效果和armcfg一样,LZ可以先查一下它的用法。
作者:
dong_root
时间:
2012-07-02 12:01
其他故障在处理,耽误了,等忙完马上去机房试下。
作者:
dong_root
时间:
2012-07-05 19:02
联系供货商重发了一块格式化过的硬盘,今天换上后做了个同步,终于OK了。
问题总结:老设备已经没有全新的配件了,供货商发的拆机件的硬盘没做格式化,导致同步异常。
fmt是万万不能做的,那是format全盘,数据会挂的,神经会崩溃的。
欢迎光临 Chinaunix (http://bbs.chinaunix.net/)
Powered by Discuz! X3.2