2. 当屏幕提示:
Please insert the fd(60)amird volume and press <Return>;,
Or ‘q’ to quit:
插入标注: ‘amird’ Drivers-SCO UNIX 5.0.4 - LH-3 的软盘, 敲 Enter
3. 当屏幕提示:
Please insert the fd(60)symha volume and press <Return>;,
Or ‘q’ to quit:
插入标注: ‘symha’Drivers-SCO UNIX 5.0.4 - LH-3 的软盘,敲 Enter。
4. 当屏幕显示:
Which routine (0-41) to replace (‘?’ to list),
‘a’ to add “slhainit” at the end [default],
‘n’ to do nothing, or ‘q’ to quit:
选择slhainit, (可能为28) 回车
5. 当屏幕显示:
Which routine (0-2) to replace (‘?’ to list),
‘a’ to add “slhapoll” at the end [default],
‘n’ to do nothing, or ‘q’ to quit:
敲 2, 回车
机器提示:‘Insert the Boot Disk and press ’,插入Boot盘,按回车。
当屏幕显示:‘Press <Enter>; to begin installation’时,按回车开始安装。
机器提示:‘Please insert (amird) package BTLD disk into the floppy drive so
that it can be extracted onto the hard disk for incorporation into
the link-kit.’
插入标注: ‘amird’ Drivers-SCO UNIX 5.0.4 - LH-3 的软盘,按回车。
选择’Contiue’,按回车。
10. 机器提示: Media device to be used:
IDE CD ROM
IDE Controller: Primary
Master or Slave: master
Accept above choices
时,将光标移至Accept above choice 敲 ENTER
11. 出现 To reset your media choice, select cancel
OK Cancel
确认Sco unix 5.0.4的光盘已经放入Cd-rom中, 将光标置于 OK ,敲 Enter
出现 keyboard: US English:
Accept above choices
选择回 车。
17. 出现
System Name: SCOSYSV
Domain name: UUCP.com
Security Profile: Traditional
Time Zone: Eastern standard/Summer Time
Language: Standard C (English)
Accept above choices
选 自 己 满 意 的 系 统 名, 若 在 网 络 上 须 选 用 网 络 管 理 员 给 定 的 域
名。选择’Accept above choices’继续。
18. 出现
Stand Enterprise System Configuration; Yes
lightweight character terminal configuration: No
If you run large data base products, choose the following:
Database Services: NO
如果需大 型 数 据 库 如 Informix,Database Service: 要 变 为 YES。
19. 出现:
Hard disk setup: Unix only: BadTracking Off
Optional Software: SCO OpenServer Enterprise system 241MB
Accept above choices
‘Hard disk setup’不需要改动,但可以将BadTracking一项置成on,检
测硬盘有没有坏道。用户可以在Optional Software项中选择需要安装的
软件,但是要注意一点:如果用户的机器配置了双CPU,千万不要选择安
装”ARCserver/Open Lite from Cheyenne (23.5 MB)”这个软件,它和
SCO 的SMP包相冲突,这是SCO Unix5.0.4系统的问题。
选择‘Accept above choices’,按回车继续。
21. 出现Root Password: Type in
Accept above choice
敲 入 你 定 的 root 口 令, 然 后 回 车。
22. 出现 Please type again to confirm, 回 车。
再次 敲 入 root 口 令, 回 车。
23. 出现Select Cancel to review or change your answer
OK Cancel
选 OK, 然 后 回 车。
24. 系统提示: extracting BTLD distribution for amird…Done
Please select the floppy device you are using
/dev/fd0
/dev/fd1
选择1,回车。系统提示:
‘Please insert the floppy for BTLD package: symha’ and Press <ENTER>;,
这时插入标注: ‘symha’Drivers-SCO UNIX 5.0.4 - LH-3 的软盘,回车。
系统开始安装。
系统安装完毕后,重启机器出现 boot:, 按回车,第一次启动系统。
配置网卡:
# scoadmin
software manager à software à Install New Software à select “scosysv” à 在Media Device 下用空格select “Floppy disk” à continue à读盘后屏幕出现“Hewlett-Packard Network Drivers (ver 1.4.6)”àselect “Install”à出现“Installation complete”选择<OK>;
NetworksàNetwork configuration manager à hardwareàAdd new adapter à找到“HP Netserver 10/100 TX Lan Adapter -pci Bus# 2,Device# 3,Function 0”àcontinueàAdd protocol时选择相应协议à”Add”à按照相应协议要求输入相应项目àConfiguration networking product “The following products were successfully configured into the system sco TCP/IP”
HP Netserver 10/100 TX LAN Adapter -pci bus#2,Device# 3,function 0àOK
重新连接核心并重启系统。
键入q
键入q,屏幕显示:
键入y,屏幕显示:
键入 y,屏幕显示:
键入 y
安装完毕,重新引导系统,即可使用磁带机。
常用的磁带机读写命令
tar tvf /dev/rct0
tar cvf /dev/rct0 directory _name or filename
tar xvf /dev/rct0
cpio -icuvdmB
30. 附加逻辑盘安装
Sco Unix不能自动识别附加逻辑盘,需要手动安装,有以下步骤:
(1)进入UNIX系统,在系统维护状态(单用户装态)下,键入命令
# mkdev hd
(2)屏幕显示
Add a hard disk to IDE controller
Add a hard disk to SCSI controller
Add a hard disk to IDA controller
(3)选择2
(4)屏幕显示:
Enter the prefix of the SCSI host adapter that supports this
Device Or press <Return>; for the default: ‘slha’
Enter h for a list of host adapters or enter q to quit:
输入amird,然后敲Enter
(5)屏幕显示:
Which ‘amird’ SCSI host adapter supports this device?
Select 0-6, or enter q to quit :
敲 0
(6)屏幕显示:
The Host Adapter parameters will be automatically configured
What SCSI Bus is this device attached to ?
Press <Return>; to use the default:0
Select 0-6, or h for help, or q to quit :
敲 0
(7)屏幕显示:
What is the Target ID for this device?
Select 0-15, or h for help, or q to quit :
敲 0
(屏幕显示:
What is the LUN of this device ?
Press <Return>; to use the default:0
Select 0-7, or h for help, or q to quit :
敲 1
(9)屏幕显示:
You are about to add the following SCSI device:
Host Adapter Adapter
Type Device Number ID LUN BUS
amird sdsk 0 0 1 0
Update SCSI configuration?(y/n) , 键入y
(10)屏幕显示:
The SCSI configuration file has been updated.
A new kernel must be built and rebooted before disk configuration can
continue.Would you like to relink at this time ? (y/n)
敲y,系统重新链接内核,并reboot。
(11) 因为加一块逻辑盘需要’mkdev hd’两次,所以重复过程(1)-(9),
屏幕显示:Do you wish to continue? (y/n) ,敲y
(12) 屏幕显示:
Display Partition Table.
Use Entire Disk for Unix
Use Rest of Disk for Unix
Create Unix Partition
Activate Partition
Delete Partition
Create Partition
Enter your choice or q to quit:
选择2,此时系统激活第二块逻辑盘
(13) 出 现 (1) Print Current Bad Track Table
(2) Scan Disk
(3) Add Entries to Current Bad Table by Cylinder/Head number
(4) Add Entries to Current Bad Track Table by sector number.
(5) Delete Entries Individually from current Bad Track Table.
Enter your choice or q to quit.
敲 回 车。
出现Bad tracks have been identified
Enter the number of bad tracks to allocate space for (or press
<return>; to use the recommended valve of 19)
敲 回 车。
出 please enter swap-space allocation, or press <return>; to get the
default allocation of 49000 1K block;
敲 回 车 (这 个 数 值 下 面 可 调, 它 指 的 是 内 存 的 对 换 区 的 大 小)
出 Please enter boot-space allocation, or press <return>; to get the default allocation of 15000 1K block.
敲 回 车
出 Do you wish to make any manual adjustments to the sizes or names of the file systems on swap area before they are create on the hard disk? (Y/N)
敲 回 车 ( 提 示 是 否 要 对 上 面 参 数 进 行 调 整)
(1屏幕显示:
Do you wish to make any manual adjustments to the size or name of the
file systems or Swap area before they are create on the hard disk? (y/n)
输入: y 并按 Enter
(19)屏幕显示:
Name Type New FS # First Block Last Block
Root Swap Root Scratch Recover Hd0a EAFS NON FS HTFS NOT USED NOT USED NON FS NON FS Whole disk no no no no no no no no 0 1 2 3 4 5 6 7 0 20000 118000 - - 2062395 2064342 0 19999 117999 2062394 - - 2064341 2064351 2072352
n[ame] Name or rename a division
c[reate] Create a new file system on this division
t[ype] Select or Change filesystem type on new filesystem
p[revent] Prevent a new filesystem from being created on this
division
s[tart] Start a division on a different block
e[nd] End a division on a different block
r[estore] Restore the original division table
Enter your choices or q to quit:
根据提示 按 'e' 设定分区的结尾的块值。
'n' 给相应分区命名。
'r' 恢复原分区。
分区划分满意后,按 q 并回车。
(20)屏幕显示:
I[nstall] Install the division Set Up shown
R[return] Return the previous menu
Please enter your choice:
按i并回车
(21)屏幕显示:
root file system is large enough that fsck will require a scratch
division of 936 blocks to clean it, Would you like a scratch division to
be allocated for you? (y/n)
敲入y并回车
(22)屏幕显示:
Remove the floppy disk from the drive, then Press any key
取出软盘,按任意键,退出依系统提示重新链接内核并reboot, 第二块逻辑
盘就安装成功了。