各位有时间帮我看看这个post输出

体元主人

@(#)OBP 4.5.21 2003/02/24 17:23 Sun Fire 280R
BBC AID Register 0000.0000.0000.0000
Power-On Reset
Executing Power On SelfTest

0>@(# )  Excalibur POST 4.7.4 2002/12/23 17:04
       /dat/fw/work/staff/firmware_re/post/post-build-4.7.4/Camelot/excal/integr
ated  (firmware_re)
0>Jump from OBP->;POST.
0>CPUs present in system: 0
0>diag-switch? configuration variable set TRUE.
0>Diag level set to MIN.
0>MFG scrpt mode set to NONE
0>I/O port set to serial TTYA.
0>Done with First Init, reset system.
0>Current CPU frequency is 400 MHz.
0>      Resetting to 1200
0>Clock Synth Reset.
0>
0>Start selftest...
0>Init CPU
0>      Cheetah_plus Version 11.0
0>DMMU Registers Access
0>DMMU TLB DATA RAM Access
0>DMMU TLB TAGS Access
0>IMMU Registers Access
0>IMMU TLB DATA RAM Access
0>IMMU TLB TAGS Access
0>;Probe Ecache
0>      Size = 00000000.00800000...
0>Ecache Data Bitwalk
0>Ecache Address Bitwalk
0>Scrub and Setup Ecache
0>Setup and Enable DMMU
0>Setup DMMU Miss Handler
0>Test and Init Temp Mailbox
0>Initializing Scan Database
0>BBC:          1483203b
0>SCSI:         15060045
0>ICHIP:        0d1e203b
0>RIO:          13e5d03b
0>IO-Bridge:    307be06d
0>CPMS0:        1142903b
0>CPMS1:        1142903b
0>CPMS2:        1142903b
0>CPMS3:        1142903b
0>CPMS4:        1142903b
0>CPMS5:        1142903b
0>Init I2C
0>Unquiesce Safari
0>Blast Fans
0>Set Trip Temp CPU 0 to 110C
0>WED JAN  2 5:57:52 GMT 8
0>Safari quick check
0>       to IO-bridge_0
0>Safari full  check
0>       to IO-bridge_0
0>;Probe and Setup Memory
0>INFO:    512MB Bank 0
0>INFO:    512MB Bank 1
0>INFO:    512MB Bank 2
0>INFO:    512MB Bank 3
0>
0>Data Bitwalk on Master
0>      Test Bank 0.
0>      Test Bank 1.
0>      Test Bank 2.
0>      Test Bank 3.
0>Address Bitwalk on Master
0>INFO: Addr walk mem test on CPU 0 Bank 0: 00000000.00000000 to 00000000.200000
00.
0>INFO: Addr walk mem test on CPU 0 Bank 1: 00000001.00000000 to 00000001.200000
00.
0>INFO: Addr walk mem test on CPU 0 Bank 2: 00000002.00000000 to 00000002.200000
00.
0>INFO: Addr walk mem test on CPU 0 Bank 3: 00000003.00000000 to 00000003.200000
00.
0>Set Mailbox
0>Setup Final DMMU Entries
0> ;P ost Image Region Scrub
0>Run POST from Memory
0>Verifying checksum on copied image.
0>The Memory's CHECKSUM value is 2844.
0>The Memory's Content Size value is 8faa2.
0>Success...  Checksum on Memory Validated.
0>Safari quick check
0>       to IO-bridge_0
0>Safari full  check
0>       to IO-bridge_0
0>;Print Mem Config
0>Caches : Icache is ON, Dcache is ON, Wcache is OFF, Pcache is ON.
0>Memory in non-interleave config:
0>      Bank 0    512MB : 00000000.00000000 -> 00000000.20000000.
0>      Bank 1    512MB : 00000001.00000000 -> 00000001.20000000.
0>      Bank 2    512MB : 00000002.00000000 -> 00000002.20000000.
0>      Bank 3    512MB : 00000003.00000000 -> 00000003.20000000.
0>Scrub Memory
0>Quick Block Mem Test
0>Quick Test 16777216 bytes at 00000000.00600000
0>40% Done...
0>Flush Caches
0>IO-Bridge unit 0 init      test
0>IO-Bridge unit 0 reg       test
0>IO-Bridge unit 0 mem       test
0>IO-Bridge unit 0 PCI DMA A test
0>IO-Bridge unit 0 PCI DMA B test
0>IO-Bridge unit 0 PCI merg  test
0>IO-Bridge unit 0 PCI iommu test
0>IO-Bridge unit 0 PCI stc   test
0>IO-Bridge unit 0 interrupt test
0>FPU Registers and Data Path
0>FPU Move Registers
0>FSR Read/Write
0>FPU Branch Instructions
0>FPU Functional Test
0>FPU BLOCK REG TEST
0>
0>Turn IO-Bridge 0 errors on
0>Turn error traps on
0>INFO:
0>      POST Passed all devices.
0>;POST: Return to OBP.
0>Return to OBP, PASS

@( # )OBP 4.5.21 2003/02/24 17:23 Sun Fire 280R
BBC AID Register 0000.0000.0000.0000
POST Results: Cpu 0
  %o0  0000.0000.0000.0000
  %o1  0000.0000.0000.0000
  %o2  0000.0000.0000.0000
CPU seeprom format: 0000.0000.0000.0002
Membase: 0000.0000.0000.0000
MemSize: 0000.0000.0010.0000
Clearing TLBs Done
Init CPU arrays Done
Init E$ tags Done
Setup TLB Done
MMUs ON
Copy Done
PC = 0000.07ff.f008.5970
PC = 0000.0000.0000.59e8
Decompressing Done
Size = 0000.0000.0006.fd20
ttya initialized
Start Reason: Initialize Machine
Configuring the machine:
?
  @(# )OBP 4.5.21 2003/02/24 17:23 Sun Fire 280R
BBC AID Register 0000.0000.0000.0000
Loading Configuration
Membase: 0000.0000.0000.0000
MemSize: 0000.0000.8000.0000
Clearing TLBs Done
Init CPU arrays Done
Init E$ tags Done
Setup TLB Done
MMUs ON
Block Scrubbing Done
Copy Done
PC = 0000.07ff.f008.5970
PC = 0000.0000.0000.59e8
Decompressing Done
Size = 0000.0000.0006.fd20
ttya initialized
Start Reason: First start after Power On
System Reset: (SPOR) (PLL)
Probing gptwo at 0,0 SUNW,UltraSPARC-III+ (1200 MHz @ 8:1, 8 MB)
   memory-controller
Probing gptwo at 1,0 Nothing there
Probing gptwo at 8,0 pci pci
Loading Support Packages: kbd-translator
Loading onboard drivers: ebus flashprom bbc power i2c dimm-fru dimm-fru
   dimm-fru dimm-fru dimm-fru dimm-fru dimm-fru dimm-fru nvram idprom
   i2c cpu-fru temperature fan-control motherboard-fru ioexp ioexp
   ioexp fcal-backplane remote-system-console power-distribution-board
   power-supply power-supply rscrtc beep rtc gpio pmc parallel
   rsc-control rsc-console serial
CPU 0 set ambient power off temperature to 70 degrees C
CPU 0 set junction power off temperature to 110 degrees C
Start Reason: First start after Power On
System Reset: (SPOR) (PLL)
Probing gptwo at 0,0 SUNW,UltraSPARC-III+ (1200 MHz @ 8:1, 8 MB)
   memory-controller
Probing gptwo at 1,0 Nothing there
Probing gptwo at 8,0 pci pci
Loading Support Packages: kbd-translator
Loading onboard drivers: ebus flashprom bbc power i2c dimm-fru dimm-fru
   dimm-fru dimm-fru dimm-fru dimm-fru dimm-fru dimm-fru nvram idprom
   i2c cpu-fru temperature fan-control motherboard-fru ioexp ioexp
   ioexp fcal-backplane remote-system-console power-distribution-board
   power-supply power-supply rscrtc beep rtc gpio pmc parallel
   rsc-control rsc-console serial
CPU 0 set ambient power off temperature to 70 degrees C
CPU 0 set junction power off temperature to 110 degrees C

Sun Fire 280R (UltraSPARC-III+) , No Keyboard
Copyright 1998-2002 Sun Microsystems, Inc.  All rights reserved.
OpenBoot 4.5, 2048 MB memory installed, Serial #54825385.
Ethernet address 0:3:ba:44:91:a9, Host ID: 834491a9.




Resetting ...


@(# )OBP 4.5.21 2003/02/24 17:23 Sun Fire 280R
BBC AID Register 0000.0000.0000.0000
Reset: 0000.0000.0000.0010SPOR
Loading Configuration
Membase: 0000.0000.0000.0000
MemSize: 0000.0000.8000.0000
Clearing TLBs Done
Init CPU arrays Done
Init E$ tags Done
Setup TLB Done
MMUs ON
Block Scrubbing Done
Copy Done
PC = 0000.07ff.f008.5970
PC = 0000.0000.0000.59e8
Decompressing Done
Size = 0000.0000.0006.fd20
ttya initialized
Start Reason: Soft Reset
System Reset: (SPOR)
Probing gptwo at 0,0 SUNW,UltraSPARC-III+ (1200 MHz @ 8:1, 8 MB)
   memory-controller
Probing gptwo at 1,0 Nothing there
Probing gptwo at 8,0 pci pci
Loading Support Packages: kbd-translator
Loading onboard drivers: ebus flashprom bbc power i2c dimm-fru dimm-fru
   dimm-fru dimm-fru dimm-fru dimm-fru dimm-fru dimm-fru nvram idprom
   i2c cpu-fru temperature fan-control motherboard-fru ioexp ioexp
   ioexp fcal-backplane remote-system-console power-distribution-board
   power-supply power-supply rscrtc beep rtc gpio pmc parallel
   rsc-control rsc-console serial
CPU 0 set ambient power off temperature to 70 degrees C
CPU 0 set junction power off temperature to 110 degrees C
Start Reason: Soft Reset
System Reset: (SPOR)
Probing gptwo at 0,0 SUNW,UltraSPARC-III+ (1200 MHz @ 8:1, 8 MB)
   memory-controller
Probing gptwo at 1,0 Nothing there
Probing gptwo at 8,0 pci pci
Loading Support Packages: kbd-translator
Loading onboard drivers: ebus flashprom bbc power i2c dimm-fru dimm-fru
   dimm-fru dimm-fru dimm-fru dimm-fru dimm-fru dimm-fru nvram idprom
   i2c cpu-fru temperature fan-control motherboard-fru ioexp ioexp
   ioexp fcal-backplane remote-system-console power-distribution-board
   power-supply power-supply rscrtc beep rtc gpio pmc parallel
   rsc-control rsc-console serial
CPU 0 set ambient power off temperature to 70 degrees C
CPU 0 set junction power off temperature to 110 degrees C

Sun Fire 280R (UltraSPARC-III+) , No Keyboard
Copyright 1998-2002 Sun Microsystems, Inc.  All rights reserved.
OpenBoot 4.5, 2048 MB memory installed, Serial #54825385.
Ethernet address 0:3:ba:44:91:a9, Host ID: 834491a9.



Rebooting with command: boot

到这就不动了，但是按ctrl+break可以到ok模式！
大家帮我看看硬件有问题么？

[ 本帖最后由 race 于 2008-1-3 07:53 编辑 ]

race

没看出问题，用光盘看看能不能引导启动机器

solaris_unix

先用900mhz的cpu试试，如果行的话，把opb升的高一点，再试1.2g的cpu!

westlife521

CPU 0 set ambient power off temperature to 70 degrees C
CPU 0 set junction power off temperature to 110 degrees C


cpu的风扇有问题了吧！

[ 本帖最后由 westlife521 于 2008-1-3 10:04 编辑 ]

体元主人

就是说 cpu温度过高？

体元主人

CPU 0 set ambient power off temperature to 70 degrees C
当周围温度达到70度 cpu关闭？
CPU 0 set junction power off temperature to 110 degrees C
当核心温度达到110度 cpu关闭

是不是这么翻译?

ilinch

没看出什么问题
0>Return to OBP, PASS

这里至少提示 post过了

yuhuohu

STOP-A
OK boot disk
boot disk0
boot disk1

boot cdrom

....试试看吧

Lainhearter

原帖由 westlife521 于 2008-1-3 10:01 发表
CPU 0 set ambient power off temperature to 70 degrees C
CPU 0 set junction power off temperature to 110 degrees C


cpu的风扇有问题了吧！

不要误导啊，这个是系统设置的温度阀值，很正常
post没看出啥问题，CPU频率太高了？

zhdss

prtenv boot-device
prtenv diag-device
devalias
看看这些设置是不是都对。