求助HP双机CLUSTER问题！工程中，急！！！！！

liz2003

# cmcheckconf -v -C /etc/cmcluster/rac.ascii
Checking cluster file: /etc/cmcluster/rac.ascii
Checking nodes ... Done
Checking existing configuration ... Done
Network interface lan0 on node host1 couldn't talk to itself.
Network interface lan1 on node host1 couldn't talk to itself.
Network interface lan0 on node host2 couldn't talk to itself.
Network interface lan1 on node host2 couldn't talk to itself.
lan0 on node host1 cannot be configured in the cluster
because it does not have an IP address, and it is not a standby lan for any other lan.
lan1 on node host1 cannot be configured in the cluster
because it does not have an IP address, and it is not a standby lan for any other lan.
lan0 on node host2 cannot be configured in the cluster
because it does not have an IP address, and it is not a standby lan for any other lan.
lan1 on node host2 cannot be configured in the cluster
because it does not have an IP address, and it is not a standby lan for any other lan.
Failed to evaluate network
cmcheckconf: Unable to reconcile configuration file /etc/cmcluster/rac.ascii
with discovered configuration information

liz2003

各位大老，有没有知道是怎么回事的啊？原来双机是好的，我修改了IP之后再检测就出现这类问题了。

disy

改ip还要改rac.ascii文件中的ip，另外hosts文件也要改。

liz2003

#

127.0.0.1       localhost       loopback

10.19.71.189  host2
10.0.0.6      host2_heart
10.19.71.188  host1
10.0.0.5      host1_heart
10.19.71.190  hostname_service
#
这是hosts中的配置，另外：
# STATIONARY_IP. They cannot be HEARTBEAT_IP.


NODE_NAME               host1
  NETWORK_INTERFACE     lan2
    HEARTBEAT_IP        10.19.71.188
  NETWORK_INTERFACE     lan0
  NETWORK_INTERFACE     lan1
  NETWORK_INTERFACE     lan3
    STATIONARY_IP       10.0.0.5
  FIRST_CLUSTER_LOCK_PV /dev/dsk/c6t0d1
# List of serial device file names
# For example:
# SERIAL_DEVICE_FILE    /dev/tty0p0

# Possible standby Network Interfaces for lan2,lan3: lan0,lan1.

NODE_NAME               host2
  NETWORK_INTERFACE     lan2
    HEARTBEAT_IP        10.19.71.189
  NETWORK_INTERFACE     lan0
  NETWORK_INTERFACE     lan1
  NETWORK_INTERFACE     lan3
    STATIONARY_IP       10.0.0.6
  FIRST_CLUSTER_LOCK_PV /dev/dsk/c6t0d1
# List of serial device file names

配置有问题吗？

liz2003

# cmruncl -v
cmruncl: Validating network configuration...
cmruncl: Failed to validate the network configuration as reported above but will try to start the cluster anyway.
cmruncl: Network validation complete
Waiting for cluster to form .............. timed out
Check the syslog files for information.
cmruncl failed: timed out waiting for cluster to form

levine

双机环境，IP地址可不是随便能改的，不行的话先改回来吧。

levine

这有个类似的案例：http://bbs.chinaunix.net/viewthr ... p;page=1#pid8051735

五“宅”一生

双机环境中如果改IP的话。
不仅需要修改网卡上的IP，还需要修改/etc/hosts文件。双机配置文件中的IP等等

然后还需要重新分发一下cluster的配置文件才能生效
cmapplyconf一下。

ts99

建议你要确认下你的那个业务ip和心跳地址是配置在了lan2和lan3上了么？（在你的集群配置文件中业务ip和心跳ip分别是lan2和lan3）
lanscan 看下ip是否配置在lan0和lan1上了，而你在集群上却配置的是lan2和lan3.

lan0 on node host1 cannot be configured in the cluster
because it does not have an IP address, and it is not a standby lan for any other lan.
lan1 on node host1 cannot be configured in the cluster
because it does not have an IP address, and it is not a standby lan for any other lan.


NODE_NAME               host1
  NETWORK_INTERFACE     lan2
    HEARTBEAT_IP        10.19.71.188
  NETWORK_INTERFACE     lan0
  NETWORK_INTERFACE     lan1
  NETWORK_INTERFACE     lan3
    STATIONARY_IP       10.0.0.5

将lanscan和netstat -rn的结果也贴出来看下，呵呵。

也可以尝试将业务ip和心跳ip分别改到lan0和lan1上，lan2和lan3做备用网卡。

liz2003

现在我的双机是好的，我把配置文件给大家看一下，我应该怎么样更改IP地址？谢谢
more /etc/hosts
#

127.0.0.1       localhost       loopback

192.168.12.98  host1
192.168.12.99  host2
192.168.12.90  hostname_service

#
#ROUTE_COUNT[0]="1"
ROUTE_GATEWAY[0]="15.104.97.14"
ROUTE_DESTINATION[0]="default"
ROUTE_COUNT[0]="1"
IP_ADDRESS[2]=192.168.12.98
SUBNET_MASK[2]=255.255.255.0
INTERFACE_NAME[2]=lan2
BROADCAST_ADDRESS[2]=192.168.12.255
INTERFACE_STATE[2]=up
IP_ADDRESS[3]=10.0.0.98
SUBNET_MASK[3]=255.255.255.0
INTERFACE_NAME[3]=lan3
BROADCAST_ADDRESS[3]=10.0.0.255
INTERFACE_STATE[3]=up
#
more /etc/cmcluster/rac.ascii
# STATIONARY_IP. They cannot be HEARTBEAT_IP.


NODE_NAME               host1
  NETWORK_INTERFACE     lan2
    HEARTBEAT_IP        192.168.12.98
  NETWORK_INTERFACE     lan0
  NETWORK_INTERFACE     lan1
  NETWORK_INTERFACE     lan3
    STATIONARY_IP       10.0.0.98
  FIRST_CLUSTER_LOCK_PV /dev/dsk/c6t0d1
# List of serial device file names
# For example:
# SERIAL_DEVICE_FILE    /dev/tty0p0

# Possible standby Network Interfaces for lan2,lan3: lan0,lan1.

NODE_NAME               host2
  NETWORK_INTERFACE     lan2
    HEARTBEAT_IP        192.168.12.99
  NETWORK_INTERFACE     lan0
  NETWORK_INTERFACE     lan1
  NETWORK_INTERFACE     lan3
    STATIONARY_IP       10.0.0.99
  FIRST_CLUSTER_LOCK_PV /dev/dsk/c6t0d1
# List of serial device file names