免费注册 查看新帖 |

Chinaunix

  平台 论坛 博客 文库
最近访问板块 发新帖
查看: 2245 | 回复: 0

[安装配置] 实际操作:SSA卡微码升级 [复制链接]

论坛徽章:
0
发表于 2006-03-30 12:03 |显示全部楼层


SSA卡升级微码
1. Login as Root
2. Select the download type - SSA Device Driver, Adapter microcode, or SSA Disk Drive microcode (see the download documents "SSA Host Software and Adapter Microcode for AIX x" where x is
4.3.3
, or
5.1.0
, or
5.2.0
, and "
SSA Disk Drive and Enclosure Microcode for AIX
"
[/url]

o Create a temporary directory
o Save the file ssaXXX.tar onto your system in your temporary directory
o cd into your temporary directory
3. Type tar -xvf ssaXXX.tar
4. If you untar more than 1 file at a time , you must run 'inutoc .' to create a new .toc file
5. Run smitty install
6. Select install & update software
7. Select install & update from ALL available software
8. Use the directory that you saved and unpacked the ssaXXX.tar file into as the install device
9. Select all filesets in this directory for install
10. Execute the command
11. Exit Smit
12. Run cfgmgr to install the microcode to adapters of the correct type
(Note that some consideration may be needed when doing this in an active HA environment, particularly if you are not going to reboot immediately.)
13. To complete the device driver upgrade you must now reboot your system
To confirm that the upgrade was a success:
Type lscfg -vl ssaX where X is 0,1... for all SSA adapters
Check that the microcode level shown in ROS Level and ID, matches the level shown in the
[url=http://www.storage.ibm.com/hardsoft/products/ssa/rs6k/adapters.html]

document "
SSA Adapters and Disk Drives - latest firmware levels (AIX)
".
Run lslpp -l|grep SSA and check that the fileset levels you have match or are above the levels shown in the document "
SSA Host Software for AIX - latest levels
".
If any of the SSA filesets are at a lower level to those shown in the above document, please repeat the whole upgrade procedure again. If after repeating the procedure, the code levels do not match the latest ones, place a call with your local IBM Service Center
14. If the adapters are in SSA loops which contain other adapters in other systems, please repeat steps 1 to 12 of this procedure on all systems as soon as possible
15. If you have 7133 D40 or T40 disk drive enclosures
[/url]
type the following commands
cd /etc/microcode
ssa_sesdld -u -f coralXXX.hex (where XXX is the highest number that you have in /etc/microcode)
16. To install latest level microcode to all SSA drives, run ssadload -u from each system in turn.
NOTE: ALLOW SSADLOAD TO COMPLETE ON ONE SYSTEM BEFORE RUNNING IT ON ANOTHER.




本文来自ChinaUnix博客,如果查看原文请点:[url]http://blog.chinaunix.net/u/16493/showart_92763.html
您需要登录后才可以回帖 登录 | 注册

本版积分规则 发表回复

  

北京盛拓优讯信息技术有限公司. 版权所有 京ICP备16024965号-6 北京市公安局海淀分局网监中心备案编号:11010802020122 niuxiaotong@pcpop.com 17352615567
未成年举报专区
中国互联网协会会员  联系我们:huangweiwei@itpub.net
感谢所有关心和支持过ChinaUnix的朋友们 转载本站内容请注明原作者名及出处

清除 Cookies - ChinaUnix - Archiver - WAP - TOP