dataware for linux的安装

yhm1980

     *****  DataWare Version 5.1 , ProWare Corp.  *****
     *****     Information about Installation     *****
  This file contains the key information about the installation
  of DataWare.
  (1) System floppy
      The system floppy (1 diskette) of this version(5.1) contains
      5 major files for installation of DataWare:
     1. dwinst
     2. cfg.a
     3. cfg.b
     4. waredata
     5. install.doc
      (Notes: Since structure changes & bugs correction, old files
          dwdaemon, wareadm.. no longer use)
  (2) Installation procedures
      1. Check if hardware (i.e. RAID) is properly set and connect
     to your servers.
      2. Power on 2 servers.
      3. If your server not yet build file system for RAId, build it
     from  one of your server (check with your UNIX supplier for
     more information about creation of devices & format a disk)
      4. Make sure your SCSI id setting in RAID is the same to each
     host.
      Under "/tmp" directory:
      1. Change dir to "/tmp"
      2. Insert DataWare system floppy in floppy drive, using tar to
     retrieve the content of diskette to "/tmp"  (e.g. use "tar xv6"
     under SCO system)
      3. Copy one of "cfg.a" or "cfg.b" to dw.cfg (depends on your host
     e.g. copy cfg.a to dw.cfg if in host A), the change dw.cfg
     (could use vi to edit)to match to your host configuration.
      4. If dw.cfg configuration is correct with your server,
     run "./dwinst" under /tmp
      Notes: 1. Be sure dw.cfg matchs your server configurations
        before running "dwinst", examples are listed
        at end of this file (Appendix).
         2. Another server takes the same procedures as stated
        above.
  (3) Finish the installation
      When you finish the installation (i.e. after run "./dwinst"),
      you can restart each server (with RAID ready), DataWare will
      be started automatically.
  (4) DataWare status/configuration check
      The status of DataWare can be checked by typing the following
      commands (dwcheck in /usr/lib/dataware/exec & /usr/bin):
      1. "dwcheck"   : No argument means to check running mode,
             role, running status.
      2. "dwcheck c" : With argument 'c', it shows the configurations.
      3. "dwcheck n" : With argument 'n', it shows the Serial Number
             of DataWare.( it is used to inform ProWare to
             get password)
  (5) Setting password
      After installation, program file "dwsetpsw" will be in
     "/usr/lib/dataware/exec"
      It is for the user to set password, the password should be set
      within 30 days after installation (password can be obtained
      from Distribution Site of ProWare Corp. by giving your Serial
      Number generated from "dwcheck n", see previous item.)
      "dwsetpsw" is an interactive inquiry program, you can run
      it without parameters.
  APPENDIX:
   The following are examples of configuration file "dw.cfg" in
   host A & host B (standby mode) respectively.
   ** Notes: 1. The title length of each field is 14 chars(include
        the ':' char)
        
         2. Leave the fields blank (like field in ts_tables) if you
        don't need, but keep the title.
        
         3. '@' character is used for a continue line of an item,   
        must be the first character in that row.(see below)
   Configure examples (HOT STANDBY)
   ******************* host A (PRIMARY SERVER)
   host_id  :A
   scsi_device  :/dev/sdb1
   ip_tables    :Real_IP1 eth0:1 192.168.0.2 255.255.255.0 192.0.0.255
   @        :Virtual_IP1 eth0:1 192.168.0.11 255.255.255.0 192.0.0.255
   fs_tables    :A /dev/sdb2 /dat1 ext2
   ap_tables    :
   ctl_ap   :A:apname
   pager_setup  :Disable
   modem_device :/dev/tty00
   pager_tables :
   reference_ip :
   ts_tables    :
   private_net  :scsi
   private_ip   :Own 192.0.0.1 Other 192.0.0.2
   public_ip    :Own 192.168.152.80 Other 192.168.152.81
   use_port1    :33864
   use_port2    :33865
   ******************* host B (STNADBY SERVER)
   host_id  :B
   scsi_device  :/dev/sdb1
   ip_tables    :Real_IP1 eth0:1 192.168.0.3 255.255.255.0 192.0.0.255
   @        :Virtual_IP1 eth0:1 192.168.0.11 255.255.255.0 192.0.0.255
   fs_tables    :A /dev/sdb2 /dat1 ext2
   ap_tables    :
   ctl_ap   :A:apname
   pager_setup  :Disable
   modem_device :/dev/tty00
   pager_tables :
   reference_ip :
   ts_tables    :
   private_net  :scsi
   private_ip   :Own 192.0.0.2 Other 192.0.0.1
   public_ip    :Own 192.168.152.81 Other 192.168.152.82
   use_port1    :33865
   use_port2    :33864
   (B)  Configure examples (DUAL ACTIVE)
   ******************* host A
   host_id  :A
   scsi_device  :/dev/sdb1
   ip_tables    :Real_IP1 eth0:1 192.168.0.2 255.255.255.0 192.168.0.255
   @        :Virtual_IP1 eth0:1 192.168.0.11 255.255.255.0 192.168.0.255
   @(back_up)   :Real_IP2 eth1:1 192.1.0.2 255.255.255.0 192.1.0.255
   @        :Virtual_IP2 eth1:1 192.1.0.11 255.255.255.0 192.1.0.255
   fs_tables    :B /dev/sdc1 /dat2 ext2
   @(this)  :A /dev/sdb2 /dat1 ext2
   ap_tables    :
   ctl_ap   :A:apname
   @        :B:apname
   pager_setup  :Disable
   modem_device :/dev/tty00
   pager_tables :
   reference_ip :
   ts_tables    :
   private_net  :scsi
   private_ip   :Own 192.0.0.1 Other 192.0.0.2
   public_ip    :Own 192.168.0.2 Other 192.168.0.3
   use_port1    :33864
   use_port2    :33865
   ******************* host B
   host_id  :B
   scsi_device  :/dev/sdc1
   ip_tables    :Real_IP1 eth0:1 192.1.0.3 255.255.255.0 192.1.0.255
   @        :Virtual_IP1 eth0:1 192.1.0.11 255.255.255.0 192.1.0.255
   @(back_up)   :Real_IP2 eth1:1 192.168.0.3 255.255.255.0 192.168.0.255
   @        :Virtual_IP2 eth1:1 192.168.0.11 255.255.255.0 192.168.0.255
   fs_tables    :A /dev/sdc2 /dat1 ext2
   @(this)  :B /dev/sdb1 /dat2 ext2
   ap_tables    :
   ctl_ap   :A:apname
   @        :B:apname
   pager_setup  :Disable
   modem_device :/dev/tty00
   pager_tables :
   reference_ip :
   ts_tables    :
   private_net  :scsi
   private_ip   :Own 192.0.0.2 Other 192.0.0.1
   public_ip    :Own 192.168.0.3 Other 192.168.0.2
   use_port1    :33865
   use_port2    :33864



本文来自ChinaUnix博客，如果查看原文请点：http://blog.chinaunix.net/u/26811/showart_317803.html