免费注册 查看新帖 |

Chinaunix

  平台 论坛 博客 文库
最近访问板块 发新帖
查看: 964 | 回复: 0
打印 上一主题 下一主题

Cisco 路由器语句汇总 [复制链接]

论坛徽章:
0
跳转到指定楼层
1 [收藏(0)] [报告]
发表于 2006-11-28 11:39 |只看该作者 |倒序浏览


Cisco 路由配置语句汇总
启动接口,分配IP地址:
router>
router> enable
router#
router# configure terminal
router(config)#
router(config)# interface Type Port
router(config-if)# no shutdown
router(config-if)# ip address IP-Address Subnet-Mask
router(config-if)# ^z
配置RIP路由协议:30秒更新一次
router(config)# router rip
router(config-if)# network Network-Number  
router(config-if)# ^z
配置IGRP路由协议:90秒更新一次
router(config)# router igrp AS-Number  
router(config-if)# network Network-Number  
router(config-if)# ^z
配置Novell IPX路由协议:Novell RIP 60秒更新一次
router(config)# ipx routing [node address]
router(config)# ipx maximum-paths Paths  
router(config)# interface Type Port
router(config-if)# ipx network Network-Number [encapsulation encapsulation-type] [secondary]  
router(config-if)# ^z
配置DDR:
router(config)# dialer-list Group-Number protocol Protocol-Type permit[list ACL-Number]
router(config)# interface bri 0
router(config-if)# dialer-group Group-Number
router(config-if)# dialer map Protocol-Type Next-Hop-Address name Hostname Telphone-Number
router(config-if)# ^z
配置ISDN:
router(config)# isdn swith-type Swith-Type  
router(config-if)# ^z
配置Frame Relay:
router(config-if)# encapsulation frame-relay [cisco | ietf ]
router(config-if)# frame-relay lmi-type [ansi | cisco | q933a ]
router(config-if)# bandwidth kilobits
router(config-if)# frame-relay invers-arp [ Protocol ] [dlci ]




router(config-if)# ^z
配置标准ACL:
router(config)# access-list Access-List-Number [ permit | deny ] source [ source-mask ]  
router(config)# interface Type Port
router(config-if)# ip access-group Access-List-Number [ in | out ]
router(config-if)# ^z
配置扩展ACL:
router(config)# access-list Access-List-Number [ permit | deny ] [ Protocol | Protocol-Number ] source source-wildcard [ Source-Port ] destination destination-wildcard [ Destination-Port ] [ established ]
router(config)# interface Type Port
router(config-if)# ip access-group Access-List-Number [ in | out ]
router(config-if)# ^z
配置命名ACL:
router(config)# ip access-list [ standard | extended ] ACL-Name
router(config [ std- | ext- ] nacl)# [ permit | deny ] [ IP-Access-List-Test-Conditions ]
router(config [ std- | ext- ] nacl)# no [ permit | deny ] [ IP-Access-List-Test-Conditions ]
router(config [ std- | ext- ] nacl)# ^z
router(config)# interface Type Port
router(config-if)# ip access-group [ACL-Name | 1~199 ] [ in | out ]
router(config-if)# ^z
配置DCE时钟:
router# show controllers Type Port  
router(confin-if)# clock rate 64000  
router(config-if)# ^z
配置PPP协议:
router(config)# username Name password Set-Password-Here  
router(config)# interface Type Port
router(config-if)# encapsulation ppp  
router(config-if)# ppp outhentication [ chap | chap pap | pap chap | pap ]  
router(config-if)# ppp pap sent-username Name password Password  
router(config-if)# ^z
PAP单向认证配置实例:
验证方:
router-server(config)# username Client password 12345  
router-server(config)# interface serial 0
router-server(config-if)# encapsulation ppp
router-server(config-if)# ppp authentication pap  
router-server(config-if)# ^z
被验证方:
router-client(config-if)# encapsulation ppp
router-client(config-if)# ppp pap sent-username Client password 12345  
router-client(config-if)# ^z
PAP双向认证配置实例:
路由器 A:
routerA(config)# username B password 12345
routerA(config)# interface serial 0
routerA(config-if)# encapsulation ppp
routerA(config-if)# ppp authentication pap
routerA(config-if)# ppp pap sent-username A password 54321
routerA(config-if)# ^z
路由器 B:
routerB(config)# username A password 54321
routerB(config)# interface serial 1
routerB(config-if)# encapsulation ppp
routerB(config-if)# ppp authentication pap
routerB(config-if)# ppp pap sent-username B password 12345
routerB(config-if)# ^z
CHAP单向认证配置实例:
验证方:
router-server(config)# username router-client password 12345
router-server(config)# interface serial 0
router-server(config-if)# encapsulation ppp
router-server(config-if)# ppp authentication chap
router-server(config-if)# ^z
被验证方:
router-client(config-if)# encapsulation ppp
router-client(config-if)# ppp authentication chap
router-client(config-if)# ppp chap hostname router-client
router-client(config-if)# ppp chap password 12345
router-client(config-if)# ^z
CHAP双向认证配置实例:
路由器 A:
routerA(config)# username routerB password 12345
routerA(config)# interface serial 0
routerA(config-if)# encapsulation ppp
routerA(config-if)# ppp authentication chap
routerA(config-if)# ppp chap hostname routerA
routerA(config-if)# ppp chap password 54321
routerA(config-if)# ^z
路由器 B:
routerB(config)# username routerA password 54321
routerB(config)# interface serial 1
routerB(config-if)# encapsulation ppp
routerB(config-if)# ppp authentication chap
routerB(config-if)# ppp chap hostname routerB
routerB(config-if)# ppp chap password 12345
routerB(config-if)# ^z
Telnet使用:
routerA# terminal monitor  
routerA# telnet IP-Address [ Router-Name ]  
routerB# [ exit | logout ]  
routerB# ++再按  
routerA# show sessions  
routerA# Connect-Number  
routerA# disconnect IP-Address [ Router-Name ]  
routerA# show user  
routerA# clear line [ 0 | 1 | 2 | 3 | 4 ]  
禁止任何Telnet到本机:
router(config)# line vty 0 4
router(config-line)# access-class ACL-Number
router(config)# ^z
设置主机名:
router(config)# hostname Set-Hostname
router(config)# ^z
router(config)# ^z
设置用户模式密码:
router(config)# line console 0
router(config-line)# login
router(config-line)# password Set-Password
router(config-line)# ^z
设置Telnet密码:
router(config)# line vty 0 4
router(config-line)# login
router(config-line)# password Set-Password
router(config-line)# ^z
设置特权模式密码:
router(config)# enable password Set-Password  
router(config)# enable secret Set-Password  
router(config)# ^z
给所有密码加密:
router(config)# service password-ancryption Set-Password-Here
router(config)# no service password-ancryption  
router(config)# ^z
设置登录Banner:
router(config)# banner motd 分隔符 Set-Banner-InFORMation-Here 分隔符  
设置接口的描述信息:
router(config-if)# description Set-Port-InFORMation-Here
router(config)# ^z
CDP的控制:
router(config-if)# cdp enable  
router(config-if)# no cdp enable  
router(config)# cdp run  
router(config)# no cdp run  
Ping的使用:
router# ping IP-Address
router# ping  
Protocol [ip]:[ Protocol-Type ]  
Target IP address:IP-Address  
Repeat count [5]:  
Datagram size [100]:  
Timeout in seconds [2]:  
Extended commands [n]:y  
Sweep range of sizes [n]:
Tracke的使用:
router# trace IP-Address [ Host-Name ]
为Cisco 4000路由器指定媒体类型:
router(config-if)# media-type 10baset  
router(config-if)# ^z
更改路由器启动顺序:
router(config)# boot system flash IOS-FileName
router(config)# boot system tftp IOS-FileName TFTP-IP-Address
router(config)# boot system rom
router(config)# ^z
修改寄存器数值:
router(config)# config-register value  
在ROM监视器中更改寄存器数值:
> o/r value
路由器密码的恢复:
冷关机,然后再开机并在60秒内按+进入ROM监视器模式
> o/r 0x2142  或 > confreg 0x2142  
router> I
router> n
router> enable
router# copy startup-config running-config
router# configure terminal
router(config)# enable secret New-Password
router(config)# config-register 0x2102
router(config)# ^z
router# copy running-config startup-config
router# reload
配置名称-主机入口:
router(config)# ip host Set-Name [ TCP-Port-Number ] IP-Address [ IP-Address 2 ]...
router(config)# ^z
定义DNS主机:
router(config)# ip name-server Server-Address [ Server-Address 2 ]...
router(config)# ^z
禁用DNS:
router(config)# no ip domain-lookup
router(config)# ^z
配置水平分割:
router(config-if)# ip split-horizon
router(config-if)# no ip split-horizon
router(config-if)# ^z
配置静态路由:
router(config)# ip route IP-Address Subnet-Mask [ Next-Hop-Address | Local-Out-Port ] [Distace ]

router(config)# ^z
配置缺省路由:
router(config)# ip defoult-network IP-Address  
router(config)# ip route 0.0.0.0 0.0.0.0 [ Next-Hop-Address | Local-Out-Port ] [Distace ]  
router(config)# ^z
其它命令:
router# show version
router# show running-config
router# show startup-config
router# show flash
router# show interface [ Type Port ]
router# show buffers
router# show protocol
router# show mem
router# show stacks
router# show processes
router# show cdp entry [ Device-Name ]  
router# show cdp neighbors
router# show cdp neighbors detail  
router# show ip router
router# show ipx router
router# show host
router# show ip protocol
router# show ip interface Type Port
router# show ipx interface Type Port
router# show ipx servers
router# show ipx traffic
router# show access-lists [ ACL-Number ]
router# show isdn status
router# show dialer  
router# show isdn active
router# show frame-relay pvc
router# show frame-relay map
router# show frame-relay lmi
router# erase startup-config
router# reload
router# setup
router# copy running-config startup-config
router# copy startup-config running-config
router# copy tftp running-config
router# copy running-config tftp
router# debug ipx routing activity
router# debug ipx sap
router# debug isdn q921
router# debug isdn q931
router# debug dialer
router# debug ip rip
router# clear interface bri [ 0 | 1 | 2 ]


本文来自ChinaUnix博客,如果查看原文请点:http://blog.chinaunix.net/u/27167/showart_207209.html
您需要登录后才可以回帖 登录 | 注册

本版积分规则 发表回复

  

北京盛拓优讯信息技术有限公司. 版权所有 京ICP备16024965号-6 北京市公安局海淀分局网监中心备案编号:11010802020122 niuxiaotong@pcpop.com 17352615567
未成年举报专区
中国互联网协会会员  联系我们:huangweiwei@itpub.net
感谢所有关心和支持过ChinaUnix的朋友们 转载本站内容请注明原作者名及出处

清除 Cookies - ChinaUnix - Archiver - WAP - TOP